OK
三星SCX-4300一体机芯片解码操作说明
一台4300，显示墨粉用尽，更换墨盒，无法打印，红灯亮。
机器被锁定。
A Samsung SCX 4300 printer, when the screen shows “Toner Empty, Replace Toner cartridge”, the red light is on, the printer is locked.
首先将打印机连上电脑。
然后启动打印机。
等预热完毕后。
电脑应该能检测出打印机的状态。
运行软件.
At first connect your printer with the PC then start your printer. Waiting for your printer finish warm-up, the PC can detect the status of your printer, running the software.
点击开始进入 Click “开始” enter：
打印机应该依次显示：
Your printer should show in turn:
PC TO DRAM IS OK (如果显示PC TO DRAM IS NG不能传输到打印机。
打
印机主板芯片的版本不对）
PC TO DRAM IS OK (If it shows PC TO DRAM IS NG are not able to transfer to the printer. Then the version of motherboard chip is not right.）
FLASH IS ERASING
FLASH PROGRMMING
然后打印机重新预热。
预热完成后修改完成。
Then the printer will warm-up again. When it finish, the modification
is finished too.
清零操作：Clearing zero operation:
菜单（Menu）->10.Maintenance（维护）-->Clear Settings（清除设置）-->All Settings（所有设置）-->OK(确定)
操作后打印机灯会闪几下，然后恢复正常的绿色，电脑墨粉状态条满格，完成清零。
The printer’s light will be flashing after the operation, then turn into normal green, it’s full at toner bar on computer, finish clearing zero.
以后当机子显示粉墨不足或刚加粉时就操作一次。
机子就恢复成满粉状态。
In future when the printer shows short of toner or after adding toner, operate it as above, the printer will return to full toner.
当打印变淡时注意及时加墨粉。
Remember to add toner when the printing turn into light color.
加粉必须自己操作。
打印机可没有自动加粉的功能。
You need to add toner by yourself. Printer have not the function of adding toner automatically.
QQ 604769802
重要说明Important specifications：
破解的方法：
1、将打印机连接到电脑。
2、启动打印机并等预热完毕。
这时电脑应能检测到打印机状态。
3、运行"SCX4300计数解码固件.exe",点击开始。
然后程序自动运行。
过两分钟左右，当退出按钮生效后点击退出。
完成破解。
1. Connect the printer to a computer.
2. Turn on the printer and waiting for finishing the warm up. At this time, the computer can check out the printer’s status.
3. Run”SCX4300 Counting Decode firmware.exe”. click “start”, then the program will run automatically. After two minutes, click “ exit“ when it turns up. Finish decoding.
清零操作：
连续按菜单（Menu）->10.Maintenance（维护）-->Clear Settings（清除设置）
-->All Settings（所有设置）--> 按OK（确定）键
注：每清零一次大约可以打印1千页。
一般鼓内的粉可打印约2-3千页。
Remark: It can print 1000 pages after clearing zero. Usually it can print 2000-3000 pages with the toner in the cartridge.
破解并清零后仍显示粉末不足的解决办法：
After cracking and clearing the printer still show the toner is not enough, what should you do:
1、连续按菜单键到8.报告(report) 再按确定打印一份系统报告。
查看第二条横线下的内容：
Firmware Version : 1.16fix（方法见附表）
如果不是则未破解，请重新破解。
2、请检查硒鼓内是否有芯片，如果有请取出芯片，或用透明胶封掉芯片触点。
3、如果前面2点没有问题，则检查清零操作是否正确。
1.Click the menu button continuously to 8 “report”then click OK to printer out a copy of
system report. Then check the content in the second line:
Firmware Version : 1.16fix（the method in the addendum）
2. Please check if there is a chip in your toner cartridge, if so please take out the chip or seal the
contact point of the chip by using the scotch tapes.
3. If there is not problem in the above two, please check if clearing zero is correct.
按菜单MENU键到8.report system data 确定。
打印一份系统资料
Press MENU to 8.report system data; and confirm to print a system document.
上面显示Firmware version :1.16fix 则表示修改成功，可以清零。
如果没用fix则没能修改，清零无效。
It shows successful modification and returns zero if the window displayed “Firmware version: 1.16fix”, or it can not be modified and invalid to return zero if not use “fix”.
如何封闭芯片How to close chip：
芯片在这个位置the position of chip
直接用透明胶粘死即可。
Directly blind the chip with scotch tape。