*2006/06/02 部品規格書料號(P/N)4B5209-D發行版次(Publish Ver)1 發行日期(Publish Date)年Y月M日D樣品料號(Sample P/N)供應商料號(Supplier P/N)部品名稱(Component)TP Half-Finished Products 供應廠商(Supplier)允昌部品說明(Component Description)：下部電極(ITO FILM)/ JA-DA5209H-IBF/允昌特性檢驗(Functional Check)可靠度檢驗(Reliability Check)附件(Attachment)OK NG N/A OKNGN/A廠商規格書(Suppliers Spec)進料檢驗單(Input Check List)尺寸量測記錄/部品測試報告(Measure Report Test Report)特性測試記錄(Functional Test Report)可靠度試驗記錄報告(Reliability TestReport)附註(P.S.)：若廠商提供的相關文件在制程條件或產品材料變更時，則需要另附報告，否則不需要另附!(The test report has to attach, or else not do it. When the process's condition or material of product in the related document was changed by supplier.)核准(Approved)承辦( Undertake)吳奕諼暫時承認(Permit for a time)SAMPLE批號(No.)數量(Quantity)期限(Date)開始(Begin)2012/5/14結束2012年Y6月M14日D(Ver)(Description) (Date) (Revision) 1 新規發行2012 吳奕諼Contents Page 1．部品構造(Structure)： (3)1-1部品規格( Spec)： (3)1-1-2特性規格(Characteristic specification)： (3)1-2實物外觀(Part photo)： (6)2．檢驗規格(Inspection spec): (6)3．包裝規格(Package spec): (6)4．環保要求(Deleterious Substance and Standard of Highest Content): (6)4-1 部品(Component): (6)4-2 包裝(Package)： (6)5．保存條件及有限期限(Storage conditions and life)： (6)6．包裝規格(Package Spec)： (7)7．工程圖(Drawing)： (10)8．客戶端檢驗規格(Customer Inspection spec)： (11)NO品名(Component)供應商(Supplier)供應商型號(Supplier P/N)厚度±公差(mm)(Thickness ±tol.)備註1 保護膜长濑PF-38D 0.057±0.0052 ITO FILM 鈴寅SCP125-BCC-150VS0.13±0.0153 PSA 王子CCL/D1-2/T3T3 0.05±0.0054 離型膜王子CCL/D1-2/T3T30.04±0.01 1-1-2特性規格(Characteristic specification)項目Item 單位Unit規格Specification量測規範Measurement面電阻Sheet resistanceOhm/sq 150±80霧度Haze % ≦1.0 JIS-K-7136 全光穿透率Total luminoustransmittance% ≧88 JIS-K-7361 穿透色度b* - ≦1.5. JIS-Z-8722ITO附著度Adhesion of ITO- 5B 百格測試翹曲Curl mm-6≦H≦+6(如下附件圖面)Appendix 1：百格測試1. 使用Elcometer N-1540百格刀(共11齒, 每齒間隔1mm)於被測物表面之水平、垂直方向各劃1刀, 刀體需與基版傾斜45度角(如下圖1)。

2. 以3M 610膠帶平行黏著於其中一個方向, 黏著5mins後, 以約60度角, 1~2mm/sec.速度撕離膠帶(如下圖2)。

3. 以放大鏡觀察剝離情形，依圖3判定。

圖1圖25B 0% None4B Less than 5%3B5-15%2B15-35%1B 35-65%0B Greater than 65%圖3附件(Attachment)： 捲曲度印刷面以－表示以＋表示印刷面H1-2實物外觀(Part photo)：解析度320x240等角視圖NO 檢驗依據(Examination Basis) 1依產品檢驗規格(LM-I-0001)Note ：Please enclose the customer of inspection specification No.8. Otherwise it will follow the internal incoming inspection standard.3．包裝規格(Package spec):NO 依據(Basis)1TP 中片包裝規格書(500x500)NO 檢驗標準(Examination Basis)1 2 環保要求Environment management standard (C69-6)環境管理物質A 表Table A-Assembly Content Restrictions( (EMS-P-017-01) NO 檢驗標準(Examination Basis)1環境管理物質B 表Table B-Packaging Content Restrictions (EMS-P-017-02)保存條件(Storage Conditions)有效期限 (Expiration Date)溫度(度) Temperature(degree)濕度(%RH) Humidity(%RH)25 ℃± 10 ℃ 55%±15% 自出貨日起 6個月6．包裝規格(Package Spec):珍珠棉真空包装,50片/包,1000片/箱.7．工程圖(Drawing)：4B5209-D98．客戶端檢驗規格(Customer Inspection spec)：保護膜除了有核氣泡之外，其餘不卡控管控方式如下圖:單位(mm)a.區域A剖面線0.6mm範圍內外觀不卡(包含刮痕壓痕凹凸點),但管控缺陷高度≦0.05mm,數量不計b.區域B依據下面所列檢驗規範管控11D e f i n i t i o n o f C o u n t i n g D e f e c t 缺陷計算的定義Defects count method 、number anddistancebetweendefects缺陷計算方式,數量及間隔 1. Linear defects scale by the length / width, dot defects scale by diameter線狀不良以長度/寬度計算,如下圖:2. Dot measurement as below diagram. ψ= ( x + y ) / 2 點狀不良計算方式如下圖, ψ= ( x + y ) / 2I n s p e c t i o n E n v i r o n m e n t 檢驗方式Inspection Environment 檢驗方式1.The luminance in appearance detecting should be between1000LUX~1300LUX, and the luminance in electronical detecting should bebetween 300LUX and 500LUX.外觀檢驗照度規格須介於1000 LUX~1300LUX ，電性檢測照度需介於300~500LUX.2.The detecting distance should be 30cm +/-5cm. 檢驗距離30cm +/- 5cm3.No other objects and raised appearance on the surfance. 光學膠表面不得有異物或凸起感4. Be inspected under general daylight lamp. 檢驗光源：普通日光燈管下光源5. Inspection view-angle: 45 degree of all around view-angle(except the light leakage on side) 檢驗視角：全視角45°X Y01 Black spot, whitespot, internalcontamination,pinholecontamination(internalcontamination),exposedsegments,black/white lines,Light Leakage(clearly visiblespot including litup and non-litup)Fiber黑點、白點、內污、色點、針孔、異物(內污)、裸線、黑白線狀、漏光(明顯可見的點，含點燈及非點燈)Note1: The LED/IR, Spots defects could be ignored if it could not be seen by checking in front of blackboard, base on it would not affect thetransparency.注一:LED/IR孔位置的點不良在黑板前檢查若不可見則可忽略, 但不可以影響穿透率.＊: There is no restriction of the distance between 2 spots. But if there arethree spots, the 3rd spot must have more than 5mm distance from othertwo spots.＊: 3點其中2點可不計距離，第3個需距離另外2點≧5mm。

Area DimensionNumberallowedMinimumseparated distanceView Area(Transparencyarea)ψ≦0.1 Ignored Ignored0.1＜ψ≦0.2 2 Ignoredψ>0.20 NG -02 Black spot, whitespot, internalcontamination,pinholecontamination(internalcontamination),exposedsegments,black/white lines,Light Leakage(clearly visiblespot including litup and non-litup)Fiber黑點、白點、內污、色點、針孔、異物(內污)、裸線、黑白線狀、漏光(明顯可見的點，含點燈及非點燈)2.1線狀Linear shape：(如下圖) (see Fig below)正視角看不見即判定OK。