当前位置:文档之家› 思科路由模拟器命令大全

思科路由模拟器命令大全

命令要在一行内打完,窗体可以自动拉大。

Aux口这个版本暂不支持。

支持三级Switch网络,需要路由时支持两级Switch。

设置的主机名中不要含有空格。

F2、F3键清屏(为了方便而加)Ctrl+P 历史命令,建议使用方向键。

Ctrl+z 回根,建议使用end命令Ctrl+Break 路由器进入ROM监控状态。

交换机清除特权密码。

双击设备进入终端操作单击设备的接口可以实现画线单击画有线的接口可以删除连线在指定的设备按下鼠标右键可以删除设备。

在指定的设备按下鼠标左键可以实现移动。

按Tab键,可以得到命令全称。

键入"?"可以得到当前状态下的命令帮助。

接收的作业名固定为当前目录下的sim.txt。

系统的配置文件是:sim.ini。

计算测验得分中,ping PCA->PCB;5 表示ping通得5分,SWAf6=2;5表示交换机SwitchA的f0/6在vlan 2时得5分。

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~PCA login:root;使用root用户password:linux;口令是linux# shutdown -hnow ;同init 0 关机# logout# login#ifconfig;显示IP地址# ifconfig eth0 <ip address> netmask <netmask> ;设置IP地址# ifconfig eht0 <ip address> netmask <netmask> down ;删除IP地址# route add 0.0.0.0 gw <ip># route del 0.0.0.0 gw <ip># route add default gw <ip> ;# route del default gw <ip> ;删除网关#route;显示网关# ping <ip># telnet <ip>交换机基本状态:switch:;交换机的ROM状态rommon>;路由器的ROM状态hostname>;用户模式hostname#;特权模式hostname(config)#;全局配置模式hostname(config-if)#;接口状态交换机口令设置:switch>enable;进入特权模式switch#configterminal ;进入全局配置模式switch(config)#hostname <hostname> ;设置交换机的主机名switch(config)#enable secretxxx ;设置特权加密口令switch(config)#enable password xxa ;设置特权非密口令switch(config)#line console 0 ;进入控制台口switch(config-line)#line vty 04 ;进入虚拟终端switch(config-line)#login;允许登录switch(config-line)#passwordxx ;设置登录口令xxswitch#exit;返回命令交换机VLAN设置:switch#vlandatabase;进入VLAN设置switch(vlan)#vlan2 ;建VLAN 2switch(vlan)#no vlan2 ;删vlan 2 switch(config)#intf0/1 ;进入端口1 switch(config-if)#switchport access vlan 2 ;当前端口加入vlan 2switch(config-if)#switchport mode trunk ;设置为干线switch(config-if)#switchport trunk allowed vlan 1,2 ;设置允许的vlan switch(config-if)#switchport trunk encap dot1q ;设置vlan 中继switch(config)#vtp domain<name> ;设置发vtp域名switch(config)#vtp password <word> ;设置发vtp密码switch(config)#vtp mode server ;设置发vtp模式switch(config)#vtp mode client ;设置发vtp模式交换机设置IP地址:switch(config)#interface vlan1 ;进入vlan 1switch(config-if)#ip address <IP> <mask> ;设置IP 地址switch(config)#ip default-gateway <IP> ;设置默认网关switch#dirflash: ;查看闪存交换机显示命令:switch#write;保存配置信息switch#showvtp;查看vtp配置信息switch#showrun;查看当前配置信息switch#showvlan;查看vlan配置信息switch#showinterface ;查看端口信息switch#show intf0/0 ;查看指定端口信息路由器显示命令:router#showrun;显示配置信息router#showinterface ;显示接口信息router#show iproute ;显示路由信息router#show cdpnei ;显示邻居信息router#reload;重新起动路由器口令设置:router>enable;进入特权模式router#configterminal ;进入全局配置模式router(config)#hostname <hostname> ;设置交换机的主机名router(config)#enable secretxxx ;设置特权加密口令router(config)#enable password xxb ;设置特权非密口令router(config)#line console 0 ;进入控制台口router(config-line)#line vty 04 ;进入虚拟终端router(config-line)#login;要求口令验证router(config-line)#passwordxx ;设置登录口令xxrouter(config)#(Ctrl+z);返回特权模式router#exit;返回命令路由器配置:router(config)#ints0/0 ;进入Serail接口router(config-if)#no shutdown ;激活当前接口router(config-if)#clock rate 64000 ;设置同步时钟router(config-if)#ip address <ip> <netmask> ;设置IP地址router(config-if)#ip address <ip> <netmask> second ;设置第二个IP router(config-if)#intf0/0.1 ;进入子接口router(config-subif.1)#ip address <ip> <netmask> ;设置子接口IP router(config-subif.1)#encapsulation dot1q <n> ;绑定vlan中继协议router(config)#config-register 0x2142 ;跳过配置文件router(config)#config-register 0x2102 ;正常使用配置文件router#reload;重新引导路由器文件操作:router#copy running-config startup-config ;保存配置router#copy running-configtftp ;保存配置到tftprouter#copy startup-configtftp ;开机配置存到tftprouter#copy tftpflash: ;下传文件到flashrouter#copy tftpstartup-config ;下载配置文件ROM状态:Ctrl+Break;进入ROM监控状态rommon>confreg0x2142 ;跳过配置文件rommon>confreg0x2102 ;恢复配置文件rommon>reset;重新引导rommon>copy xmodem:<sname> flash:<dname> ;从console 传输文件rommon>IP_ADDRESS=10.65.1.2;设置路由器IPrommon>IP_SUBNET_MASK=255.255.0.0 ;设置路由器掩码rommon>TFTP_SERVER=10.65.1.1;指定TFTP服务器IPrommon>TFTP_FILE=c2600.bin;指定下载的文件rommon>tftpdnld;从tftp下载rommon>dirflash: ;查看闪存内容rommon>boot;引导IOS静态路由:ip route <ip-address> <subnet-mask> <gateway> ;命令格式router(config)#ip route 2.0.0.0 255.0.0.0 1.1.1.2 ;静态路由举例router(config)#ip route 0.0.0.0 0.0.0.0 1.1.1.2 ;默认路由举例动态路由:router(config)#iprouting ;启动路由转发router(config)#routerrip ;启动RIP路由协。

相关主题