连接器群组测试报告c o n n e c t o r t e s t r e p o rtDocument serial number【NL89WT-NY98YT-NC8CB-NNUUT-NUT108】DESCRIPTION：产品说明 CONNECTOR 高度连接器PART NO.：料号DATE：日期2012/12/28DOCUMENT NO.：文件号码REV.：版本AINDEX索引1.SCOPE 3适用范围2.APPLICABLE DOCUMENTS 3适用的文件3.TEST CONDITIONS AND SEQUENCE 3 5测试条件与次序4.TEST METHOD OF INSPECTION 5 10测试检验方法5.SUMMARY OF THE QUALIFICATION 1127TEST RESULT测试结果6. APPENDIX 28附件1. SCOPE适用范围1.1TESTED SAMPLES: 85 pcs.测试样品数: 85个1.2PURPOSEThis qualification test report contains the quality requirements, testprocedures and test results of a qualification test program on the part no:目的这个合格检验报告针对泰强料号: 进行测试，测试内容包含合格测验规范、测验程序和测验的结果2.APPLICABLE DOCUMENTS适用的文件2.1EIA-RS-3642.2Test report of FCN:3. TEST CONDITIONS AND SEQUENCE测试条件与次序3.1TEST CONDITIONSUnless otherwise specified, tests and examinations were conductedunder conditions within the following ranges:Temperature: 20±5℃Atmospheric Pressure: 650 to 800 millimeters to inches) of MercuryRelative Humidity: 40% to 70%测试条件除非额外规定,检验依下面的范围之内的条件下实施：温度: 20 ± 5 ℃大气压力：650至800毫米( 至英寸) 水银柱高。

相对湿度：40%到70%QUALIFICATION TEST SEQUENCE测试检验方法4-1EXAMINATION OF PRODUCTVisual inspection and dimensional examination in compliance withapplicable specifications and documents were performed. The testsamples shall be free from defects such as damage, creep,deformation, blister and burrs that are detrimental to the functionsand appearances of test samples.外观检验目视检查和尺寸的检验依照已实施之规范及文件做其检验内容。

测验样品不应有影响功能性及外观不良等缺陷，如损害、潜变、变形、水泡和毛边等问题。

4-2CONTACT RESISTANCEThe test was performed in accordance with EIA-364-23. Opencircuit voltage is 20 mV maximum and test current is 100 mAmaximum level contact resistance requirement is 40 mΩ (resistance of termination wires shall be deducted from the reading) for initialsamples, ., samples have not been subjected to any environmentaltest, and is 80 mΩ for environmentally stressed samples..接触阻抗此测试依据EIA-364-23.来执行检测。

测试电压是20 mV最大值并且测验电流是 100 mA最大值初始样品最大接触阻抗为40 mΩ(线材的阻抗值应从所得到的电阻值中扣除)样品经过环境的测试最大接触阻抗为80 mΩ。

4-3INSULATION RESISTANCEInsulation resistance was measured between adjacent contacts after applying 500 VDC for 1 minute. The test was performed inaccordance with EIA-364-21. Minimum insulation resistancerequirement is 100 MΩ for initial samples.绝缘阻抗绝缘阻抗为相接连之端子经由500 VDC通过一分钟后，所量测之值。

此测试依据EIA-364-21来执行检测。

样品未受任何环境测验，最小绝缘体阻抗需求对于初始样品为100 MΩ。

4-4DIELECTRIC WITHSTANDING VOLTAGEA 500 V AC was applied between two adjacent contacts of the testsamples for 1 minute. While applying the voltage, the leakagecurrent was monitored and shall be less than mA. The test wasperformed in accordance with EIA-364-20.耐电压相接连之端子经由一 500 V AC流电通过一分钟。

在通过电压时,漏电电流应小于 mA。

此测试依据EIA-364-20.来执行检测。

4-5TEMPERATURE RISINGContact series-wired, apply test current of loaded rating current tothe circuit, and measure the temperature rising by probing onsoldered area of contacts. After the temperature becomes stabilized deduct ambient temperature from the measured value.温升连续接触连线，适用对电路测试装载电流，通过在接触的焊接区域量测所提升温度，当温度变的稳定以后，从测量的温度数值中扣除环境温度。

4-6VIBRATIONThe test was performed in accordance with EIA-364-28B. Matedsamples were subjected to vibration test per axis. Test duration foreach axis was 2 hours (total of 6 hours). The test current was 100 mA for all contacts, which were wired in series and attached to anelectrical discontinuity monitor. Throughout the test, electricaldiscontinuity of 1 microsecond or longer shall not be allowed.振动此测试依据EIA-364-28来执行检测。

将公母配合的连接器受每轴心的振动测验。

每一个轴心的测验持续时间是2 小时 ( 总共6小时) 。

针对每一端子通过100 mA的检测电流，且每一端子需接一串接电路至一电子不连续性监视器。

经由测试，一微秒或者更长的电不连续性将不被允许。

4-7MECHANICAL SHOCKThe test was performed in accordance with EIA-364-27B. Matedsamples were subjected to 6 shocks per axis (total of 18 shocks)complied with half-sine waveform which had a 30G peak level and a normal duration of 11 milliseconds. The test current was 100 mA for all contacts, which were wired in series and attached to an electrical discontinuity monitor. Throughout the test, electrical discontinuity of1 microsecond or longer shall not be allowed机械冲击依据EIA-364-27来执行检测。

紧配的样品以30g’s、半正旋波、11毫秒以及各轴向经过六次的冲击(总共18次)。

针对每一端子通过100 mA的检测电流，且每一端子需接一串接电路至一电子不连续性监视器。

经由测试，一微秒或者更长的电不连续性将不被允许。

4-8TERMINAL RETENTION FORCEThe contact retention force was the peak force measured while the contact of connector was pulled out from the insulator housing of the connector perpendicularly. Upon completion of the test, the contact retention force shall exceed .端子保持力当连接器端子从塑料垂直地被拔出后，端子保持力为量测到的最大值数据。