PRODUCT SPECIFICATIONSFor Customer: ___ _____ □: APPROVAL FOR SPECIFICATIONCustomer Model No. _ _ □: APPROVAL FOR SAMPLE Module No.: XH-T070QYH-01CP Date : 2016-09-20T a b l e o f C o n t e n t sNo. Item Page1 Cover Sheet(Table of Contents)2 Revision Record3 General Specifications4 Outline Drawing5 Absolute Maximum Ratings6 Electrical Specifications and Instruction Code7 Optical Characteristics8 Reliability Test Items and Criteria9 Packing ReliabilityF o r C u s t o m e r’s A c c e p t a n c e:Approved By CommentPREPARED CHECKED VERIFIED BY QADEPTVERIFIED BY R&DDEPT杭州旭虹科技有限公司2. Revision RecordDate Rev.No. Page Revision Items Prepared 2016-09-20 V0 The first release ZHP3. General SpecificationsXH-T070QYH-01CP is a TFT-LCD module. It is composed of a TFT-LCD panel, driver IC, FPC, TP a back light unit. The 7.0 display area contains 800 x1280pixels and can display up to 16.7M colors. This product accords with RoHS environmental criterion.Item Contents Unit Note LCD Type TFT(IPS) -Display color 16.7MViewing Direction Free viewing O’Clock Operating temperature 0~+50 ℃Storage temperature -10~+60 ℃Module size Refer to outline drawing mm Active Area(W×H) 94.20X150.72 mmNumber of Dots 800×1280 dotsLCD Controller N/A -CTP Controller GT928 or EQUPower Supply Voltage 3.3VOutline Dimensions Refer to outlinedrawing-Backlight 5X4-LEDs (white) pcs Weight --- g Interface MIPI-4LANES -4. Outline Drawing2.37±0.27.0"T F T 800*R G B *1280V i e w d i re c t i o n : A l l94.20 L C D A .A 96.20 S E N S O R A .A 103.46±0.2 B L & S E N S O R O D 57.95150.72 LCD A.A90.42152.72 SENSOR A.A162.03±0.2 BL 10.859.8515.0614.06C o m p o n e n t0.20 O C A 4.25±0.395.20 C O V E R V .A 10.35115.90±0.05 C O V E R O D 6.22151.72 COVER V.A 180.80±0.05 COVER OD14.5612.031.5 M A X0.30±0.05S T I F F E N E R P IC O N T A C T S ID E44.23±0.537.49±0.50.5±0.10P 0.5*(8-1)=3.5±0.0527.28.30.29.38.40.39.31.32.34.33.36.35.37.R S TG N DM I P I _C K NG N DG N DM I P I _2NM I P I _2PG N DN CP W M ON CV C LL E D -L E D -N CN CA V D DL E D +L E D +M I P I _C K PM I P I _3NM I P I _3PG N DN CN CG N DG N DA V E EN CN C1.V D D4.5±0.100.3±0.053.5±0.30D E T A I L A (4:1)D E T A I L A4.50±0.3S T E E L S T I F F E N E R (T = 0.2M M )B L AC K T A P E (T =0.07M M )C O N N E C T O R :F H 33J -40S -0.5S H (10)1.00±0.05 L E N S 4-R 1.50±0.054.35 M A X (L C M +P C B +C O M P O N E N T )245°-+-+C o m p o n e n tP C BC o m p o n e n t B L A C K P R I N T I N GL E D C I R C U I T D I A G R A M :5*4=20E A I f =80m A1.V C O M2.3.M I P I _0NM I P I _0P5.6.4.G N DN CV D D I N8.9.10.M I P I _1N7.M I P I _1PG N DV D D I N11.12.14.13.16.17.15.20.19.18.23.21.22.24.25.26.2.3.R E S E T5.6.4.I N TG N DG N D8.7.S C LG N DS D A29.07±0.513.57±0.516.00±0.535.36±0.522.81±0.5(90.00)B L A C K T A P E (T =0.07M M )11.506.87161.29 SENSOR OD 12.10 3.31(6.74)6.0060.00C H A N G E T H E C O V E R O F C T P12016.02.24S U K A N G Y A NC H A N G E T H E C O V E R O F C T P22016.04.06S U K A N G Y A N1112222C H A M F E R :0.2M M2L A B E L2-R 0.22-R 0.202-R 2.00Ｈａｎｇｚｈｏｕ　Ｘｕ　Ｈｏｎｇ　Ｔｅｃｈｎｏｌｏｇｙ　Ｃｏ．，ＬｔｄＸＨ－Ｔ０７０ＱＹＨ－０１ＣＰ杭州旭虹科技有限公司5. Absolute Maximum Ratings(Ta=25℃)5.1 Electrical Absolute Maximum Ratings.(Vss=0V ,Ta=25℃)Item Symbol Min. Max. Unit NotePower Supply Voltage V CC-0.3 4.6V1，2 Logic Signal Input/Output VoltageV IOVCC-0.3 3.0VNotes:1. If the module is above these absolute maximum ratings. It may become permanently damaged. Using the module within the following electrical characteristic conditions are also exceeded, the module will malfunction and cause poor reliability.2. V CC >V SS must be maintained.5.2 Environmental Absolute Maximum Ratings.ItemStorage OperatingNote MIN. MAX. MIN. MAX.Ambient Temperature-10℃60℃0℃50℃1,2 Humidity ---- 31. The response time will become lower when operated at low temperature.2. Background color changes slightly depending on ambient temperature.The phenomenon is reversible.3. Ta<=40℃:85%RH MAX.Ta>=40℃:Absolute humidity must be lower than the humidity of 85%RH at 40℃.6. Electrical Specifications and Instruction Code6.1 Electrical characteristics(Vss=0V ,Ta=25℃)ParameterSymbolCondition Min Typ Max Unit Note Power supply VCC Ta=25℃ 2.8 3.3 3.6 V Inputvoltage‘H’ V IH V CC =2.8V 0.7V CC - V CC V ‘L’V IL V CC =2.8V 0 - 0.3V CC V Current ConsumptionI CC1 Normal mode - 80 -mA I CC2 Sleep mode - 1 - mA MIPI CLKPeriod- 4.0 4.44 4.8 ns Frequen cy-208225250MHz6.2 LED backlight specification(VSS=0V ,Ta=25℃)Note:ItemSymbol Condition Min Typ Max Unit Note Supply voltage Vf If=20X4mA - 15 - V Uniformity ΔBp If=20X4mA 75 % Luminance (W/o CTP)LvIf=20X4mA-350Cd/m2I LED VS TEMP6.3 Interface signalPin No. Symbol I/O Function1 VCOM P Common Voltage(-1.756 ±0.3 V)2-3 VDDIN P A power supply for the analog power.4 GND P Ground.5 RESET I Reset pin. Setting either pin low initializes the LSI. Must be reset after power is supplied6 NC - No connection7 GND P Ground.8 MIPI-0N I MIPI-DSI Data differential signal input pins. (Data lane 0)9 MIPI-0P I MIPI-DSI Data differential signal input pins. (Data lane 0)10 GND P Ground.11 MIPI-1N I MIPI-DSI Data differential signal input pins. (Data lane 1)12 MIPI-1P I MIPI-DSI Data differential signal input pins. (Data lane 1)13 GND P Ground.14 MIPI-CLKN I MIPI-DSI CLOCK differential signal input pins.15 MIPI-CLKP I MIPI-DSI CLOCK differential signal input pins.16 GND P Ground.17 MIPI-2N I MIPI-DSI Data differential signal input pins. (Data lane 2)18 MIPI-2P I MIPI-DSI Data differential signal input pins. (Data lane 2)19 GND P Ground.20 MIPI-3N I MIPI-DSI Data differential signal input pins. (Data lane 3)21 MIPI-3P I MIPI-DSI Data differential signal input pins. (Data lane 3)22 GND P Ground.23-24 NC - No connection25 GND P Ground.26 NC - No connection27 PWMO I CABC PWM signal output.28 NC - No connection29 VCL POutput voltage pin,use it to generate vcom voltageby a VR circuit (output voltage -2.5V)30 GND P Ground.31-32 LEDK P LED back light(Cathode)33-34 NC - No connection35 AVEE P Analog supply negative voltage36-37 NC - No connection38 AVDD P Analog supply positive voltage39-40 LEDA P LED back light(Anode)CTP interfacePin No.Symbol I/O Function1 VDD P Power for CTP2-3 GND P Ground4 SCL I Clock signal for Serial interface5 SDA I Data signal for serial interface6 GND P Ground7 INT I Interruption signal8 RESET I Reset the controller7. Optical CharacteristicsItem Symbol Condition Min. Typ. Max. UnitNote Brightness (With CTP) Bp θ=0° Φ=0°- 300 - Cd/m 2 1 Uniformity⊿Bp 75 - %1,2Viewing Angle3:00Cr≥10 - 80 - Deg 36:00 - 80 - 9:00 - 80 - 12:00- 80 - Contrast Ratio Cr θ=0° Φ=0° 650 800 - 4 Response TimeT r - 25 - ms 5T f - 25 - ms Color ofCIE CoordinateW x θ=0° Φ=0° 0.29 - 1,6y 0.33 - Rx 0.66 - y 0.32 - Gx 0.27 - y 0.58 - Bx 0.13 - y 0.12 - NTSC RatioS-70-%Note ：The parameter is slightly changed by temperature, driving voltage and materielNote 1: The data are measured after LEDs are turned on for 5 minutes. LCM displays full white.The brightness is the average value of 9 measured spots. Measurement equipment PR-705 (Φ8mm)Measuring condition:- Measuring surroundings: Dark room. - Measuring temperature: T a=25℃.- Adjust operating voltage to get optimum contrast at the center of the display.Measured value at the center point of LCD panel after more than 5 minutes while backlight turning on.Note 2: The luminance uniformity is calculated by using following formula.⊿Bp = Bp (Min.) / Bp (Max.)×100 (%)Bp (Max.) = Maximum brightness in 9 measured spotsBp (Min.) = Minimum brightness in 9 measured spots.Active areaNote 3: The definition of viewing angle:Refer to the graph below marked by θ and ФNote 4: Definition of contrast ratio.( Test LCD using DMS501)()dotsselected non of Brightness dotsselected of Brightness Cr ratio Contrast -=Note 5: Definition of Response time. (Test LCD using DMS501):The output signals of photo detector are measured when the input signals are changed from “black” to “white”(falling time) and from “white” to “black”(rising t ime), respectively. The response time is defined as the time interval between the 10% and 90% of amplitudes.Refer to figure as below.The definition of response timeNote 6: Definition of Color of CIE Coordinate and NTSC Ratio.Note 7: Definition of cross talk.Cross talk ratio(%)=|pattern A Brightness-pattern B Brightness |/pattern A Brightness*100Electric volume value=3F+/-3HexColor gamut:100%triangleNTSC of area triangleRGB of area S ⨯=Pattern APattern B Measurement point(center)5min 30min 30min 8. Reliability Test Items and CriteriaNo Test ItemTest conditionCriterion1High Temperature Storage60℃±2℃ 96HRestore 2H at 25℃ Power off1. After testing,cosmetic and electrical defects should not happen.2. Total currentconsumption should not be more than twice of initial value.2 Low Temperature Storage-10℃±2℃ 96H Restore 2H at 25℃ Power off3High Temperature Operation 50℃±2℃ 96HRestore 2H at 25℃Power on 4 Low Temperature Operation 0℃±2℃ 96HRestore 4H at 25℃Power on 5High T emperature/Humidity Operation 60℃±2℃ 90%RH 96H Power on6 Temperature Cycle--10℃←-----------------→60℃after 5 cycle, Restore 2H at 25℃ Power off7 Vibration Test 10Hz~150Hz, 100m/s 2, 120min Not allowed cosmetic and electrical defects.8Shock TestHalf- sine wave,300m/s 2,11msNote: Operation: Supply 2.8V for logic system.The inspection terms after reliability test, as below ITEM Inspection Contrast CR>50% IDD IDD<200% Brightness Brightness>60% Color Tone Color Tone+/-0,059. Precautions for Use of LCD Modules9.1 Handling Precautions9.1.1 The display panel is made of glass. Do not subject it to a mechanical shockby dropping it from a high place, etc.9.1.2 If the display panel is damaged and the liquid crystal substance inside itleaks out, be sure not to get any in your mouth, if the substance comes intocontact with your skin or clothes, promptly wash it off using soap and water.9.1.3 Do not apply excessive force to the display surface or the adjoining areassince this may cause the color tone to vary.9.1.4 The polarizer covering the display surface of the LCD module is soft andeasily scratched. Handle this polarizer carefully.9.1.5 If the display surface is contaminated, breathe on the surface and gentlywipe it with a soft dry cloth. If still not completely clear, moisten cloth withone of the following solvents:— Isopropyl alcohol— Ethyl alcoholSolvents other than those mentioned above may damage the polarizer.Especially, do not use the following:— Water— Ketone— Aromatic solvents9.1.6 Do not attempt to disassemble the LCD Module.9.1.7 If the logic circuit power is off, do not apply the input signals.9.1.8 To prevent destruction of the elements by static electricity, be careful tomaintain an optimum work environment.a. Be sure to ground the body when handling the LCD Modules.b. Tools required for assembly, such as soldering irons, must be properlyground.c. To reduce the amount of static electricity generated, do not conductassembly and other work under dry conditions.d. The LCD Module is coated with a film to protect the display surface. Becare when peeling off this protective film since static electricity may begenerated.9.2 Storage precautions9.2.1 When storing the LCD modules, avoid exposure to direct sunlight or to thelight of fluorescent lamps.9.2.2 The LCD modules should be stored under the storage temperature range. Ifthe LCD modules will be stored for a long time, the recommend condition is:Temperature : 0℃～40℃Relatively humidity: ≤80%9.2.3 The LCD modules should be stored in the room without acid, alkali andharmful gas.9.3 The LCD modules should be no falling and violent shocking duringtransportation, and also should avoid excessive press, water, damp and sunshine.。