【精编推荐】CombineUserGuide船舶M站操作手册AMOSConnect(7.4.27) – Quick User Guide (EnglishVersion)Table of ContentChapter 1 – Connection between Inmarsat and PC…..……. Page3Chapter 2 - AMOSConnect Quick Installation…………..... Page 42.1 – Verify Connection Page 5Chapter 3 –AMOSConnect simple user guide...………….. Page 73.1 – Start AMOS Connect Page 73.2 – Editing address books Page 73.3 – Compose new email Page 103.4 – Compose FAX (Text Only) Page 143.5 – Compose FAX (Attachment) Page 163.6 - Compose Telex Page 183.7 – Dial and connect Page 203.8 – Check connection status Page 22Chapter 4 – FAQ Session..………………………………... Page 23Appendix I ……………………………………………….. Page 36Important Note:After install AmosConnect, please make sure you backup the folder C:\AM32\AMPO (or C:\AMPO) at least once per month, so you could recovery all your AmosConnect setting and history in case you PC have technical problemHow to Backup AmosConnect and Reinstall in New PC1.Copy the folder C:\AM32\AMPO ( the mail path folder could be found in Help/aboutAmosConnect) at least once per month to other PC or Hard Disk2.If PC with AmosConnect have problem, copy the AMPO folder to the new pc3.Install AmosConnect version 7.4 by click AC-7.4.16 (Setup.exe) from you AmosConnect CD ,the Setup.exe is in the source folder , don’t use setup.bat unless you want to install newdatabase4.After installation , click “Connect to existing post office”5.Chose Local Database and browse to the folder of AMPO6.In C:\Am32, or C:\program file\AmosConnect, find out file “ ResetDeviceComputer.exe “ anddouble click it ( to reset the modem driver)7.Your AmosConnect should be fully recoveredChapter 1 – Connection between Inmarsat and PCInmarsat B:Inmarsat Mini-M:Inmarsat F (RS232 Direct Connection):Inmarsat F( With ISDN TA):ComputerInmarsat B Terminal (DTE Port)(9 Pin COM Port)ComputerMini-M Terminal (9 Pin Data Port)(9 Pin COM Port)Computer(9 Pin COM Port)Inmarsat-F Terminal(ISDN Port)ISDN LineISDN TA Serial LineFAX MachineTelephone(9 Pin or 25 pin )Computer(9 Pin COM Port)Inmarsat-F Terminal(RS232 Port)RS232 SerialFAX MachineTelephoneChapter 2- AMOSConnect Quick installation1.Place AMOSConnect CD in the CDROM drive2.Double click to open ”My Computer” on desktop3.Double click on CD-ROM drive4.Double click “Setup”, a window will pop up, keep waiting during the installation untilyou see the message ‘AMOS-Mail restored. Please try to run AMOS Connect andconfirm’5.After installation has been completed, the window will close automatically.6.For Re-Installation, follows these steps :a)Remove “AMOS Connect” under “Add/Remove Programs” in “Control Panel”b)Delete the whole directory C:\am32c)Start installation from step 12.1 Verify Connection1.Double the icon ‘AMOS Connect’ on desktop2.Click the ‘Dail’ button, follow by the ”Connect” button3.If no error message pop up and you can see statistics count , that means the connection is inprogress.Now, you can start to use AMOS Connect.4.If error message pop up or you cannot make a connection, please refer to Chapter 4 – FAQ Sessionfor troubleshoot for troubleshootChapter 3 – AMOSConnect simple user guide3.1 Start AMOS Connect1.Double click the icon ‘AMOS Connect’ on desktop3.2 Editing Address Books (E-mail, Fax and Telex Service)2.Click the ‘Address’ button, the ‘Address Book’ window will pop up3.Click the ‘New’ button, the ‘New Directory’ will pop up4.Adding contacts in Address Book :a.Adding Email address:i.Select ‘Internet’ in the ‘Template’ pull-down menuii.Input the email address in the Address. (e.g. The Email address is service@ as shown in the following example)b.Adding FAX number:i.Select ‘Fax” in the ‘Template’ pull-down menuii.Input the fax number in the Address. (e.g. The fax number is +852******* as shown in the following example)c.Adding telex number:i.Select ‘Telex’ in the ‘Template’ pull-down menuii.Input the telex number in the Address. (e.g. The telex number is +8533103 as shown in the following example.)3.3 Compose new email1.Click the ‘New’ icon at top-left hand corn, the ‘New Message’ and ‘Address Selection’ windowswill pop up2.Click to select the recipient, click ‘T o’, ‘Cc’ or ‘Bcc’ to put it on the list3.Click ‘Close’ when finish4.Enter the subject and content for the email5.Click ‘Attach’ button if you want to add attachment, the ‘Add Attachment(s)’ window will pop up6.Find and click on the target file, click ‘open’.7.The attachment will be put into the new message8.Click the ‘Send’ button9.The email will be put in ”Send Queue”, pending for delivery10.The email will also make a copy in “SendBox” for record3.4 Compose FAX - Text Only, only send FAX with English content 1.Click the ‘New’ button, the ‘New Message’ and‘Address Selection’ windows will pop up2.Click to select the recipient, click ‘To’, ‘Cc’ or ‘Bcc’ to put it on the list3.Click ‘Close’ when finish4.Enter the subject and content for the email5.Click the ‘Send’ button3.5 Compose FAX - Attachment method, can be used with any printing-capable software1.Start AMOS Connect2.Under any printing-capable software, select ‘AMOS Fax’ for printing. For example : FAX under“MS Word” document :3.Print the document, select to use the printer “AMOS-Mail Fax”4.After press “OK” , The document will be sent to ‘AMOS Connect’ , select the recipient list andpress the ‘Send’ button to send it3.6 Compose Telex1.Click the ‘New’ button, the ‘New Message’ and ‘Address Selection’ windows will pop up2.Click to select the recipient, click ‘To’, ‘Cc’ or ‘Bcc’ to put it on the list3.Click ‘Close’ when finish4. Enter the subject and content for the email。