当前位置:文档之家› 机械工程师常用英语词汇

机械工程师常用英语词汇


圆柱度 cylindricity 线轮廓度 profile of any line 面轮廓度 profile of any plane 位置公差 正齿轮 斜齿轮 轮齿 节圆 齿顶圆 齿顶高 齿根高 齿厚 齿间 齿宽 压力角 交点 销 圆柱销 圆锥销 开口销 键 平键 半圆键 轴承 滚动轴承 向心铀承 密封装置 锁紧装置 粗糙度 基本尺寸 实际尺寸 极限尺寸 零线 凸台 偏差 上偏差 下偏差 垂直度 倾斜度 同轴度 tolerance in position, position tolerances spur gear spiral gear gear tooth pitch circle addendum circle, outside circle height of addendum height of addendum circular thickness tooth space tooth width angle of pressure point of intersection pin round pin taper pin cotter pin, split key flat key half round key, woodruff key bearing rolling bearing radial bearing sealing equipment locking equipment roughness basic size actual size limits size zero line boss deviation upper deviation lower deviation perpendicularity angularity concentricity
中文
圆锥顶 相贯体 相贯线 尺寸 定形尺寸 定位尺寸 左视图 后视图 仰视图 辅助图
英文
conic apex intersecting bodies line of intersection Size size dimension location dimension right view rear view, back view bottom view
run-out cycle run-out tolerance in form, form 形状公差 tolerance 直线度 straightness 圆柱度 cylindricity tolerance in position, 位置公差 position tolerances 投影 三视图 主视图 俯视图 左视图 立体 顶点 棱 点 直线 变形 水平线 铅垂线 正垂线 相交 平行 垂直 内圆角 弹簧 平行线 垂直线 长度 宽度 高度 相接 相交 相切 相贯 肋 轮廓线 截平面 截交线 圆弧 椭圆 双曲线 抛物线 圆 projection three-view drawing frontal view top view left side view solid center vertex edge point line straight line deformation horizontal line vertical line, frontalprofile line horizontal--profile line intersection parallel perpendicular fillet spring parallel line perpendicular line length width height built-up inter section tangent penetration rib outline, contour line cutting plane line of section arc ellipse hyperbola parabola circle
中文
对称度 位置度 跳动 圆跳动 全跳动 轴测图 公差 Ra Cb Ch Fp fzβ fzα ffα F''j Fr f''j 粗糙度 圆度 锥度规 fHβ Fβ Fα
英文
symmetry true position run-out cycle run-out total run-out axonometric drawing tolerance arithmetic medium roughness crowning width of tooth
剖切平面迹线 cutting plane line 箭头 基准 基准线 基准面 中心孔 装配图 性能尺寸 大小尺寸 总体尺寸 外形尺寸 配合尺寸 交线 外圆角 尖角 倒角 轮缘 缘、边、环 轴肩 arrowhead datum datum line datum plane central hole assembly drawing characteristic dimension size dimension outer dimension fit dimension intersecting line, line of intersection round sharp corner chamfer flange of wheel rim shoulder
中文
基轴制 间隙 形状公差 直线度 平面度 圆度
英文
shaft-basic system of fits clearance tolerance in form, form tolerance straightness flatness roundness
间隙配合 clearance fit 同轴度 粗实线 跳动 圆跳动 concentricity continuous thick line, full line, visible line
中文
螺距 牙型 旋向 右旋螺纹 左旋螺纹 头数 导程 粗牙 细牙 螺栓 螺钉 螺柱 螺母 垫片
英文
pitch of thread form of thread direction of turning right-hand thread left-hand thread number of thread lead coarse thread fin thread bolt screw stud nut washer
full section half section partial section, 局部剖视图 broken-out section 斜剖视图 oblique section 旋转剖视图 aligned section echelon section, offset 阶梯剖视 section 复合剖视 compound section 剖面图 重合剖面 section, sectional view coincide section, revolved section
移出剖面 removed section section line symbols for section剖面符号 lining dimensional chain of 零件尺寸链 machinery parts technological dimension 工艺尺寸链 chain 剖面线
相邻齿距 difference between 误差 adjacent pitchs dimensional chain 尺寸链 装配尺寸 assemble dimension chain 链 组成环 减环 comsisting link decreasing link
最大极限尺寸 maximum limit of size 凹坑 轴颈 轮毂 轮辐 直纹滚花 网纹滚花 键槽 退刀槽 拔模斜度 油槽 油封 标准件 螺纹 外螺纹 内螺纹 大径 小径 concave pit shaft neck hub spoke, spoke of wheel straight knurling s hatching knurling key-way escape pattern draft oil groove oil seal standard parts thread external thread internal thread major diameter minor diameter
auxiliary view partial view, broken 局部视图 view 斜视图 旋转视图 剖视图 全剖视 半剖视 oblique view revolved view, aligned view sectional view, section
பைடு நூலகம்
crowning depth of tooth cumulative pitch error MAX. PERM. Tooth alignment variation MAX. PERM. Profile angle variation profile form error radial composite error radial run-out radial tooth-to-tooth composite error roughness; degree of roughness roundness taper gauge tooth alignment error total alignment error total profile error
中文
英文
中文
习惯画法 局部放大图 零件图 对称度 细实线 虚线 点划线 双点划线 波浪线
英文
conventional drawing drawing of partial enlargement detail drawing, working drawing symmetry continuous thin line dot line, dashed line, hidden line dash and dot line double dots line break line
齿距误差fp adjacent pitch error 公差带 tolerance zone 最小极限尺寸 minimum limit of size 标准公差 公差等级 基本偏差 配合 间隙配合 过盈 过盈配合 过渡配合 基孔制 封闭环 增环 standard tolerance tolerance grade fundamental deviation fit clearance fit interference interference fit transition fit hole-basic system of fits closing link increasing link
相关主题