几种猫路由设置方法合勤P642首先P642是TELNET模式，所以首先在运行里输入TELNET 确定后开启TELNET！然后点击“连接”——“远程系统”——在主机名里添入192.168.1.1这是P642默认IP！然后连接出现Password：在后面输入默认的密码1234回车后进入下面的设置界面Copyright (c) 1994 - 2000 ZyXEL Communications Corp.Prestige 642R Main MenuGetting Started Advanced Management1. General Setup 21. Filter Set Configuration3. Ethernet Setup 22. SNMP Configuration4. Internet Access Setup 23. System Password24. System MaintenanceAdvanced Applications11. Remote Node Setup12. Static Routing Setup15. SUA Server Setup 99. Exit这些都是各功能界面按前面的数字和回车来进入各界面！下面进入1. General Setup 界面，只要输入“1”回车即可，以此类推！我只登出需要更改的界面！-----------------------------------------------------------------------------Menu 1 - General SetupSystem Name= p642 （随便起名）Location=Contact Person's Name=Route IP= Y es （要开启路由这里必须改成YES）Route IPX= NoBridge= No （这里必须NO）Press ENTER to Confirm or ESC to Cancel:----------------------------------------------------------------------设置好后回车存储，然后按ESC回主界面！再进如3. Ethernet Setup 继续进2.TCP/IP and DHCP Setup----------------------------------------------------------------------------- Menu 3.2 - TCP/IP and DHCP Ethernet SetupDHCP SetupDHCP= ServerClient IP Pool Starting Address= 192.168.1.33Size of Client IP Pool= 32Primary DNS Server= 202.97.224.68Secondary DNS Server= 202.97.230.4Remote DHCP Server= N/ATCP/IP Setup:IP Address= 192.168.1.1IP Subnet Mask= 255.255.255.0RIP Direction= BothV ersion= RIP-1202.97.224.68和202.97.230.4为当地电信的2个DNS，各地不同。

只有一个也可其他的按照我的设置改即可回车存储下面回到主菜单进入4. Internet Access Setup----Menu 4 - Internet Access SetupISP's Name= ChangeMe （这个名字也随便了）Encapsulation= ENET ENCAP 必须和电信提供参数一致Multiplexing= LLC-based 必须和电信提供参数一致VPI #= 0 （VPI VCI值问当地电信）VCI #= 35Service Name= N/AMy Login= N/AMy Password= N/ASingle User Account= Y es 为ＮＡＴ开启项，默认为ＹＥＳIP Address Assignment= StaticIP Address= 218.10.165.196 （这是电信给你的IP）ENET ENCAP Gateway= 218.10.165.193（这是电信给你的网关IP，网关每户不同）Press ENTER to Confirm or ESC to Cancel:--------------------------------------------------------------回主菜单进11. Remote Node Setup再继续进1，-----------------------------------------------------------------------Menu 11.1 - Remote Node ProfileRem Node Name= ChangeMe 不是一行Route= IPActive= Y es 不是一行Bridge= NoEncapsulation= ENET ENCAP 不…… Edit PPP Options= N/A Multiplexing= LLC-based 不…… Rem IP Addr= 218.10.165.193 Incoming: 不…… Edit IP/IPX/Bridge= NoRem Login= N/ARem Password= N/AOutgoing: Session Options:My Login= N/A Edit Filter Sets= NoMy Password= N/AAuthen= N/APress ENTER to Confirm or ESC to Cancel:----------------------------------------------------------------------注意上面应该为两列，为防止混淆我用文字夹在中间了，后面的没夹文字自己注意218.10.165.193为网关每户都不同！进12. Static Routing Setup然后续进1，在进1，Menu 12.1.1 - Edit IP Static RouteRoute #: 1Route Name= testActive= Y esDestination IP Address= 0.0.0.0IP Subnet Mask= 0.0.0.0Gateway IP Address= 218.10.165.193Metric= 2Private= NoPress ENTER to Confirm or ESC to Cancel:以上修改后就可开启路由了！另外23. System Password是修改进入密码的！24. System Maintenance 然后继续进4再继续进21就自动重起路由器，这在掉线后恢复连接有用！这跟拔掉路由器电源再插上类似，像重起电脑！另外24. System Maintenance里面有一项是恢复出厂默认的，具体的忘了，自己试吧！记住每页设置完一定要回车存储！下面是关于PPPoE模式路由的开启！用telnet登陆，在运行里输入telnet 192.168.1.1。

密码初始为1234，进入：Copyright (c) 1994 - 2000 ZyXEL Communications Corp.Prestige 642R-11 Main MenuGetting Started Advanced Management1. General Setup 21. Filter Set Configuration3. Ethernet Setup 22. SNMP Configuration4. Internet Access Setup 23. System Password24. System Maintenance25. IP Routing Policy SetupAdvanced Applications11. Remote Node Setup12. Static Routing Setup15. SUA Server Setup 99. Exit设置Router 工作模式:进入菜单1Menu 1 - General SetupSystem Name= hfkjLocation=huafengContact Person's Name=sjzRoute IP= Y esRoute IPX= NoBridge= No注意必须打开Route IP进入菜单3.2Menu 3.2 - TCP/IP and DHCP Ethernet Setup DHCP SetupDHCP= ServerClient IP Pool Starting Address= 192.168.1.33 Size of Client IP Pool= 32Primary DNS Server= 0.0.0.0Secondary DNS Server= 0.0.0.0Remote DHCP Server= N/ATCP/IP Setup:IP Address= 192.168.1.1IP Subnet Mask= 255.255.255.0RIP Direction= BothV ersion= RIP-1Multicast= NoneIP Policies=Edit IP Alias= No进入菜单4Menu 4 - Internet Access SetupISP's Name= ChangeMeEncapsulation= PPPoEMultiplexing= LLC-basedVPI #= 0VCI #= 35Service Name=My Login= 82303#1My Password=******Single User Account= Y esIP Address Assignment= DynamicIP Address=N/AENET ENCAP Gateway= N/A进入菜单11.1Menu 11.1 - Remote Node ProfileRem Node Name= ChangeMe Route= IPActive= Y es Bridge= NoEncapsulation=PPPoE Edit PPP Options=NoMultiplexing= LLC-based Rem IP Addr=0.0.0.0Incoming: Edit IP/IPX/Bridge= NoRem Login=Rem Password=********Outgoing: Session Options:My Login=sjz6852xxx@adsl2 Edit Filter Sets= NoMy Password=********* PPPoE Idle Timeout(sec)=0Authen= CHAP/PAP PPPoE Service Name=现在就好了，在进入菜单第24项— System Maintenance 的第一项检查网络是否通了没有！另：各地VPI，VCI各不相同，自己打电话问电信去！。