华为AC+AP无线配置方法组网示意图：前提条件：1)所有设备工作正常2)依据上述组网建立测试环境1)正确配置AC使AP发放SSID:“SSID-Temp1”、“SSID-Temp2”和“SSID-Temp3”，且对应业务vlan为：vlan-1，vlan-2，vlan-3；配置Switch[Switch]vlan batch 100 101 102 103[Switch]interface GigabitEthernet0/0/1[Switch-GigabitEthernet0/0/1]description Link-to-AP[Switch-GigabitEthernet0/0/1]port link-type trunk[Switch-GigabitEthernet0/0/1]port trunk pvid vlan 100[Switch-GigabitEthernet0/0/1]port trunk allow-pass vlan 100 101 102 103 [Switch-GigabitEthernet0/0/1]quit[Switch]interface GigabitEthernet0/0/2[Switch-GigabitEthernet0/0/2]description Link-to-AC[Switch-GigabitEthernet0/0/2]port link-type trunk[Switch-GigabitEthernet0/0/2]port trunk allow-pass vlan 100 101 102 103 [Switch-GigabitEthernet0/0/2]quit配置AC1.配置接口和VLAN信息，AC为DHCP Server，为AP和client分配地址[AC]vlan batch 100 101 102 103[AC]interface GigabitEthernet0/0/1[AC-GigabitEthernet0/0/1]description Link-to-SW[AC-GigabitEthernet0/0/1]port link-type trunk[AC-GigabitEthernet0/0/1]port trunk allow-pass vlan 100 101 102 103[AC-GigabitEthernet0/0/1]quit[AC]dhcp enable[AC]interface vlanif 100[AC -Vlanif100]description for-ap[AC -Vlanif100]ip address 192.168.100.1 24[AC -Vlanif100]dhcp select interface[AC-Vlanif100]quit[AC]interface vlanif 101[AC -Vlanif101]description for-STA[AC -Vlanif101]ip address 192.168.101.1 24[AC -Vlanif101]dhcp select interface[ACVlanif101]quit[AC]interface vlanif 102[AC -Vlanif102]description for-STA[AC -Vlanif102]ip address 192.168.102.1 24[AC -Vlanif102]dhcp select interface[ACVlanif102]quit[AC]interface vlanif 103[AC -Vlanif103]description for-STA[AC -Vlanif103]ip address 192.168.103.1 24[AC -Vlanif103]dhcp select interface[ACVlanif103]quit2. 配置AC WLAN基础配置AC]wlan ac-global ac id 1 carrier id other [AC]wlan ac-global country-code CN[AC]wlan[AC -wlan-view]wlan ac source interface Vlanif 100 [AC-wlan-view]ap-auth-mode no-auth3.配置AC WLAN 业务参数#创建wlan-ess接口[AC]interface Wlan-Ess 0[AC-Wlan-Ess0]port hybrid pvid vlan 101[AC-Wlan-Ess0]port hybrid untagged vlan 101[AC-Wlan-Ess0]quit[AC]interface Wlan-Ess 1[AC -Wlan-Ess1]port hybrid pvid vlan 102[AC -Wlan-Ess1]port hybrid untagged vlan 102[AC -Wlan-Ess1]quit[AC]interface Wlan-Ess 2[AC -Wlan-Ess2]port hybrid pvid vlan 103[AC-Wlan-Ess2]port hybrid untagged vlan 103[AC-Wlan-Ess2]quit#创建WMM模板，采用默认参数[AC-wlan-view]wmm-profile name wmm-profile-0[AC -wlan-wmm-prof-wmm-profile-0]quit#创建安全模板，采用默认参数[AC-wlan-view]security-profile name security-profile-0[AC-wlan-sec-prof-security-profile-0]quit#创建流量模板，采用默认参数[AC-wlan-view]traffic-profile name traffic-profile-0[AC-wlan-traffic-prof-traffic-profile-0]quit#创建服务集并绑定WLAN-ESS接口、安全模板和流量模板[AC-wlan-view]service-set name service-set-0[AC-wlan-service-set-service-set-0]ssid SSID-Temp1[AC-wlan-service-set-service-set-0]wlan-ess 0[AC-wlan-service-set-service-set-0]service-vlan 101[AC-wlan-service-set-service-set-0]security-profile name security-profile-0 [AC-wlan-service-set-service-set-0]traffic-profile name traffic-profile-0[AC-wlan-view]service-set name service-set-1[AC-wlan-service-set-service-set-1]ssid SSID-Temp2[AC-wlan-service-set-service-set-1]wlan-ess 1[AC-wlan-service-set-service-set-1]service-vlan 102[AC-wlan-service-set-service-set-1]security-profile name security-profile-0 [AC-wlan-service-set-service-set-1]traffic-profile name traffic-profile-0[AC-wlan-view]service-set name service-set-2[AC-wlan-service-set-service-set-2]ssid SSID-Temp3[AC-wlan-service-set-service-set-2]wlan-ess 2[AC-wlan-service-set-service-set-2]service-vlan 102[AC-wlan-service-set-service-set-2]security-profile name security-profile-0 [AC-wlan-service-set-service-set-2]traffic-profile name traffic-profile-0 #创建射频模板，并绑定WMM模板[AC-wlan-view]radio-profile name radio-profile-0[AC-wlan-radio-prof-radio-profile-0]wmm-profile name wmm-profile-0[AC-wlan-radio-prof-radio-profile-0]quit#配置VAP并下发[AC-wlan-view]ap 0 radio 0[AC-wlan-radio-0/0]radio-profile name radio-profile-0[AC-wlan-radio-0/0]service-set name service-set-0[AC-wlan-radio-0/0]service-set name service-set-1[AC-wlan-radio-0/0]service-set name service-set-2[AC-wlan-radio-0/0]quit[AC-wlan-view]commit ap 02)查看STA可用的无线网络，有预期结果1；3)STA1、STA2和STA3分别关联“SSID-Temp1”、“SSID-Temp2”和“SSID-Temp3”，并进行ping 网关测试，有预期结果2。

拓展总结业务网关设置在二层交换机上也可以正常工作。