网络设备维护手册第一章交换机操作手册此部分档使用本项目交换机型号如下：S7506E/S5120/S5130/WX3024E设备登陆 Con sole 登陆1、通过交换机 Con sole 口进行本地登录是登录交换机的最基本的方式，也是配置通过 其他方式登录交换机的基础。

连接示意图如下:2、把电脑和交换机连接好后，交换机上电开机，然后在电脑上进行如下操作，首先点击开 始— ＞程序— ＞附件— ＞通讯— ＞超级终端输入完成点击确定，出现下面界面，连接时使用选择 COM 口，一般台式机为COM1或COM2 ,[Mie衽，凸储曲工且囱甘理工貝 卜 <■重 i*土社辛网将甘靳爭茕匚了葫林就笊卜 o 事折工貝 已聆想倍自妄全卜 &堆手己副•惮卜 riueiytMia^Tyff _（宙in 血於序遵営耳器心启动f画阴 G 实用工且卜L^fa I. K-亠 .计髓 ：i-s ■士亠IffPCConsclol I□思師埒庶.二]RF二 ErM 匚5 ntft__新連直甫向辱9 Euetwtr 丈件传辰片寻＜|HETxtCa 亠钞HS^.e 口 If IMi-A 应元在甲万问和默讪佰 SflcwsCT.TS.S ■-打幵讯“亢占痂建Office 交老打开后出现下面图示，输入名称，可以任意输而笔记本经过转接，可能会产生COM3或COM4，也有可能是其他的，你可以在下面的选择项里看到，选择完成后点击确定。

通过上面的选择，现在到了对端口属性进行设置，一般情况下没有进行过修改，默认只要点击还原为默认值就可以了，然后再单击确定。

之后敲回车即可，会出现H3C＞提示符，说明已经与交换机连接，可以进行配置了，如果没有可以重启交换机或检查连接是否正确。

<H3C><H3C>----------------------------------------------------------------------------------------------------------------------------- telnet登陆i新建用户名密码local-user admin /admin 为用户名password cipher h3c@123 /h3c@123 为密码authorization-attribute level 3 /授权admin 用户的等级为3,3 为最高级service-type tel net /授权admi n用户的登陆方式，可以为ftp、tel net等#telnet server enable /开启telnet 服务使用电脑连接至交换机：开始菜单-输入cmd,如下图，输入telnet，输入用户名密码admin/h3c@123即可登录交换机交换机加电开机显示sarting ....*************************************************************H3C S5510-24P BOOTROM, Versio n 142*************************************************************Copyright (c) 2004-2008 Hangzhou H3C Tech. Co., Ltd.Creation date: Mar 12 2008, 11:17:30CPU Clock Speed : 200MHzBUS Clock Speed : 33MHzMemory Size : 128MBThe switch Mac is: 000F-E2B1-BD60Press Ctrl-B to enter Boot Menu (10)Auto-booting...DecompressImage .................................................................................................................................................. ...................................................................................................................................................... O K! Starting ...******************************************************************************* Copyright (c) 2004-2008 Hangzhou H3C Tech. Co., Ltd. All rights reserved. ** Without the owner's prior written consent, ** no decompiling or reverse-engineering shall be allowed. *******************************************************************************It will take a long time to get configuration file, please wait...Startup configuration file does not exist.User interface aux0 is available.<H3C>%Apr 26 12:03:53:611 2000 H3C SHELL/4/LOGIN: Console login from aux0 <H3C><H3C>sys[H3C][H3C]sysname neiwang[neiwang-luser-admin]pa sin admin fg)safely Save current configuration safely<cr>[neiwang]save s[neiwang]save safely Are you sure? [Y/N]:yPlease input the file name(*.cfg)[fla](To leave the existing filename unchanged, press the enter key):Validating file. Please wait...Now saving current configuration to the device.Saving configuration fla. Please wait...Configuration is saved to flash successfully. [neiwang]qu<neiwang>saveThe current configuration will be written to the device. Are you sure? [Y/N]:n <neiwang>sys System View: return to User View with Ctrl+Z.[neiwang]DHCP Snooping was enabled.[neiwang-GigabitEthernet1/0/15]qu[neiwang]vlan 26[neiwang-vlan26] [neiwang-GigabitEthernet1/0/15]port access vlan 26[neiwang-GigabitEthernet1/0/15]qu[neiwang-GigabitEthernet1/0/25]port trunk permit all ? ............................ Done.<cr>[neiwang-GigabitEthernet1/0/25]undo port link-type ................................ Done. [neiwang-GigabitEthernet1/0/25]spstatic Display static ARP entry[neiwang-GigabitEthernet1/0/25]speed ? 10Specify speed of current port 10Mb/s100 Specify speed of current port 100Mb/s1000 Specify speed of current port 1000Mb/s auto Enable port's speed negotiation automatically [neiwang-GigabitEthernet1/0/25]speed au[neiwang-GigabitEthernet1/0/25]speed auto [neiwang-GigabitEthernet1/0/25]du [neiwang-GigabitEthernet1/0/25]duplex au [neiwang-GigabitEthernet1/0/25]duplex auto [neiwang-GigabitEthernet1/0/25]qu [neiwang]dhcp [neiwang]dhcp-snooping ? <cr>[neiwang]dhcp-snoopingDHCP Snooping has already been enabled. [neiwang]int g 1/0/25 [neiwang-GigabitEthernet1/0/25]dhcp [neiwang-GigabitEthernet1/0/25]dhcp-snooping ? information Specify Option 82 service trustTrusted port[neiwang-GigabitEthernet1/0/25]dhcp-snooping tr [neiwang-GigabitEthernet1/0/25]dhcp-snooping trust <cr> [neiwang-GigabitEthernet1/0/25]dhcp-snooping trust [neiwang-GigabitEthernet1/0/25]qu [neiwang]dis valn ?INTEGER<1-4094> VLAN ID All the VLANsDynamic VLAN ID Reserved VLAN ID Static VLAN ID<cr> [neiwang]dis arp ?Display ARP entry by special IP addressall Display static&dynamic ARP entry dynamicDisplay dynamic ARP entryinterface Display by Interfacesource-suppression Display ARP source suppression[neiwang]dis vlan all [neiwang]dis arpall dynamicreserved statictimervlanvpn-instanceDisplay ARP timerDisplay by VLANDisplay ARP entries by VPN name[neiwang]dis arp IP Address allType: S-Static MAC Address[neiwang]dis mac-a [neiwang]dis mac-address D-DynamicVLAN ID Interface[neiwang]%Apr 26 12:30:36:527 2000 neiwang SHELL/4/LOGIN: admin login2000 neiwang SHELL/4/LOGOUT: admin logout frominterface Vlan-interface4000 //路由添加管理口Aging Type from 26 12:31:14:141 vlanip address //路由添加管理地址IP#interface GigabitEthernet1/0/52 //回程路由ip route-static //指定要回跳的路由第二章 无线维护手册设备登陆此步骤参考设备登陆设备常用操作 注册 APwlan ap AP1 model WA2620i-AGN serial-id219801A0CNC6 radio 1 service-template 10 radio enableradio 2 service-template 10 radio enable配置 SSID 名称wlan service-template 10 ssid TAXZFWZX bind WLAN-ESS 10 authentication-method open-system cipher-suite tkip security-ie wpa service-template enable /新建服务模板 10 /ssid 为 TAXZFWZX/绑定无线接口 10 /以下为加密方案/启用服务模板/新建无线接口 10，供服务模板调用 /以下为认证信息h3c@123 # interface WLAN-ESS10 port-security port-mode psk port-security tx-key-type 11key port-security preshared-key pass-phrase si/MODEL 的型号一定要和实际 /手工注册方式序列号一定要正确 /2620i 是双频 AP /调用服务模板 /启用射频口。