5
低碱玻纤网格布（密度7 X 7 ） Low玻璃纤维网格布 alkali glass fiber mesh cloth (density Fiberglass Mesh of 7 X 7) 填充料 Filler 原木木屑、碳化硅、蛭石，滑石粉 Logs of wood chips, silicon carbide, vermiculite, talc
ALL LEVELS OF MGO BOARD TABLE
GRADE C
氧化镁（活性80% ），氯化镁，木屑， 珍珠岩，高碱玻纤网格布，改性剂 Magnesium oxide (activity 80%), magnesium chloride, sawdust, perlite, high alkali glass fiber mesh, modifier 选料，配料，发泡，成型，脱模（ 6 小 时），切边，自然保养（ 3 天），发货 。 Choice of materials, ingredients, foam, molding, mold release (6 hours), trimming, natural maintenance (3 days) shipping. 同一配料，一次性投入原料 The same ingredients, raw materials, one-time investment
GRADE A
GRADE B
氧化镁（活性85% ），氯化镁，木 屑，珍珠岩，中碱玻纤网格布，改性剂 Magnesium oxide (activity 85%), magnesium chloride, sawdust, perlite, alkali glass fiber mesh, modifier 选料，配料，发泡，成型，脱模（ 12 小时），切边，自然保养（ 10 天）发 The 货。 choice of materials, ingredients, foam, molding, mold release (12 hours), trimming, natural maintenance (10 days) shipping.
中碱玻纤网格布（密度5 X 5 ） 高碱玻纤网格布（密度4 X 4 ） HighMiddle-alkali fiberglass mesh (density alkali glass fiber mesh (density 4 X 4) of 5 x 5) 胶合板使用过的木屑、农作物秸秆及谷 原木木屑、珍珠岩、灰石灰粉或滑石粉 壳、珍珠岩 Wood sawdust, perlite, limestone, ash Plywood used in wood chips, crop or talcum powder straw and husk, perlite 先搅拌料浆；将搅拌好的料浆注入下一 级搅拌机，加填充料等进行第二次搅拌 First mixing the slurry; the stirred slurry injection a mixer, add fill material such as second mixing 一层底浆、一层面浆、两层或多层中碱 玻纤网格布、一层无纺布 Layer of pulp, a pulp level, two or more layers of alkali glass fiber mesh, a layer of non-woven 12 小时脱模，自然养护 10 天 12 hours demoulding, nature conservation 10 days 使用调速高速搅拌机，一台或多台搅拌 机配合一台成型机，所有搅拌一次完成 The governor high-speed mixer, one or more mixers with a molding machine, all stirring once
同一配料，一次性投入原料 The same ingredients, raw materials, one-time investment
4
统一配方，不调整 Unified formula, do not adjust
无改性剂 No Modifier 高碱玻纤网格布（密度3 X 3 ） Highalkali glass fiber mesh (density 3 X 3) 胶合板使用过的木屑、农作物秸秆及 谷壳、珍珠岩 Plywood used in wood chips, crop straw and husk, perlite 使用调速高速搅拌机，一台或多台搅 拌机配合一台成型机，所有搅拌一次 完成 The governor high-sp with a molding machine, all stirring once
二层高碱玻纤网格布、一层浆、一层 二层高碱玻纤网格布、一层浆、二层无 无纺布 纺布 Two-story high-alkali glass fiber Two-story high-alkali glass fiber mesh, mesh, a layer of slurry, a layer of a layer of syrup, two-story non-woven non-woven 使用高温6 小时脱模，自然养护 3 天 6 hours using high-temperature mold release, Nature Conservation 3 days 不可砂光，只能用光面 Non-sanding, only with the smooth 手工切割，厚度误差 +/-0.8mm, 长度和 Hand宽度误差 15mm cutting, the thickness error of + /0.8mm, the error of length and width of 15mm 使用高温4 小时脱模，无自然养护 Use of high temperature 4 hours stripping, nature conservation 不可砂光，只能用光面 Non-sanding, only with the smooth 手工切割，厚度误差+/-1.2mm, 长度 和宽度误差 25mm Hand-cutting, the thickness error of + /-1.2mm, the error of length and width of 25mm
10 砂光 Sanding
进行砂光处理，砂光面和光面都可以作 不可砂光，只能用光面 Non-sanding, 为正面 Will been sanded,can use for a only with the smooth positive both of sanding and smooth 电脑切割，厚度误差+/-0.5mm, 长度和 宽度误差 5mm Computer cutting, the thickness error of + /-0.5mm, length and width of the error of 5mm
6
7
8
9
面浆、中浆、底浆分三次搅拌，添加剂 改性剂单独搅拌，最后进行混合搅拌 搅拌方式 Mixing Surface pulp, pulp, pulp of the bottom method three times stirring, additives, modifiers separate mixing, final mixing 磨砂底浆、面浆、中浆、四层或更多层 玻璃纤维网格布，不用无纺布 成型工艺 Molding Frosted end of the slurry, the surface process of pulp in the pulp, four or more layers of glass fiber mesh, without nonwoven 24 小时脱模，自然养护 28 天 24 脱模与养护 Mold release and hours demoulding, nature conservation conservation 28 days
化学分析 13 Chemical analysis
进行出厂检验，记录，保证每批产品都 形式检验，无记录，无法对产品追根溯 能追根溯源 Factory inspection records 源 Form of inspection records, can not 无检验，无记录 Inspection, no record to ensure that each batch of product be traced can be traced
不同等级的玻镁板对比表
级别 Level NO. 对比项目 Comparison item 玻镁板成分 magnesium board composition 氧化镁（活性85% ），硫酸镁，木 屑，碳化硅，低碱玻纤网格布，改性剂 Magnesium oxide (activity 85%), magnesium sulfate, wood chips, silicon carbide, low-alkali glass fiber mesh,modifier
电脑自动控制切割，厚度误差 +/0.1mm ，长度和宽度误差 +/-1mm 11 精准度 Accuracy Computer control of cutting, the thickness error of + /-0.1mm, length and width of error of + /-1mm 12 检验 Test 严格进行出厂检验，记录，保证每批产 品都能追根溯源 Stringent factory inspection records to ensure that each batch of product can be traced
GRADE D
氧化镁（活性70% ），氯化镁，木 屑，珍珠岩，高碱玻纤网格布 Magnesium oxide (activity 70%), magnesium chloride, sawdust, perlite, high alkali glass fiber mesh