0.005
1.11
主轴端面之偏摆
Run out of main spindle outer surface
1-4
0.01
1.12
主軸外面之偏擺
Run out of main spindle outer surface
0.01mm
1.13
床檯X軸方向運動之直線度
Straightness of table movement in the X axis.
NO.
¯¯¯
日沛電腦配件（上海）有限公司
RI PEI computer accessory (Shanghai) Co., Ltd.
加工中心精度检验規範
机型：
机号：
SERIAL NO.
中國上海松江區新橋鎮申港路3636號
No.3636 Shenggang Road,Xin Qiao Songjiang Shanghai China
Y≦500 0.02
500＜Y≦800 0.025
800＜Y≦1250 0.03
1250＜Y≦2000 0.04
1.5
X轴方向运动与床台基准沟侧面之平行度
Parallelism between movement in X axis direction and Side surface of table reference slot
車刀角度停止後重複定位精度
Repeatability of tool angle after tool stop.
0.001mm
1.20
車刀加工後定位精度
Repeatability of tool angle after machining part
0.001mm
1.21
主軸振動檢測
Spindle vibration detection
Measured value
1.6
各轴方向相互运动之直角度
Perpendicularity Between movement in X axis direction and Y axis direction and Z axis direction
a.
X-Y
轴Place
0.012/300
b.
X-Z
轴Place
C
8〞
1-8
3.0反复精度检查Repetition accuracy inspection单位Unit: sec
项
次
NO
检查项目
Inspection item
测试方法图
Measuring method diagram
许可差
Permissible deviation
实际
测量值
Measured value
a.
X-Z
面内
0.06/1000
b.
Y-Z
面内
1-1
单位Unit : mm
项
次
NO
检查项目
Inspection item
测试方法图
Measuring method diagram
许可差
Permissible deviation
实际
测量值
Measured value
1.3
床台X轴方向之运动与其上面之平行度
0.005
固定端300处
At 300 position
0.015
1.9
主轴轴线与Z轴轴线运动间的平行度
Parallelism between the spindle axis and
the Z-axis motion
a:0.015/300
b:0.015/300
Hale Waihona Puke 1.10主轴在Z轴方向之移(松)
动量
Movement of main spindle in Z axis direction
2.2
回转运动之定位精度
Positioning accuracy of straight line movement
By
ISO230-2
Cycle times
: Two times
C
15〞
1-7
3.0反复精度检查Repetition accuracy inspection单位Unit: sec
项
次
NO
Parallelism between movement in X axis direction and table upper surface
X≦500 0.02
500＜X≦800 0.025
800＜X≦1250 0.03
1250＜X≦2000 0.04
1.4
床台Y轴方向之运动与其上面之平行度
Parallelism between movement in Y axis direction and table upper surface
1.Apply a fixed indicator to the straight edge as the figure shown.
2.Adjust to get reading at both ends of the straight edge.
2.Move the table 300 mm in X-axis direction.
检查项目
Inspection item
测试方法图
Measuring method diagram
许可差
Permissible deviation
实际
测量值
Measured value
3.1
直线运动之反复定位精度ISO230-2
Positioning repeatability of straight line movement
≦0.6mm/s
(Ref)
2.0定位精度检查Positioning accuracy inspection单位Unit : mm
项
次
NO
检查项目
Inspection item
测试方法图
Measuring method diagram
许可差
Permissible deviation
实际
测量值
Measured value
By
ISO230-2
Cycle times
: Two times
X
0.006
Y
Z
单位Unit: sec
3.2
回转运动之重复定位精度
ISO230-2
Positioning repeatability of straight line movement
By
ISO230-2
Cycle times
: Two times
0.01/300
1.15
旋轉檯旋轉偏擺
Table runout(XY)
0.015mm/300
1.16
旋轉檯旋轉偏擺
Table runout(Z)
0.005mm
1.17
車刀角度換刀後重複定位精度
Repeatability of tool angle after tool change.
0.001mm
1.18
3.Record the largest value difference as the measurement value.
0.01/300
1.14
床檯Y軸方向運動之直線度
Straightness of table movement in the Y axis
1-5
1.Apply a fixed indicator to the straight edge as the figure shown.
2.1
直线运动之定位精度
ISO230-2
循环次数:
2次
Positioning accuracy of straight line movement
By
ISO230-2
Cycle times
: Two times
X
L≦1000
0.01
1000＜L≦2000
0.015
L≧2000
0.02
Y
Z
单位Unit: sec
Measuring method diagram
许可差
Permissible deviation
实际
测量值
Measured value
4.1
循圓精度
Roundness
Geometry contouring evaluated by Renishaw Ballbar system(ISO 230-1)
2.Adjust to get reading at both ends of the straight edge.
2.Move the table 300 mm in X-axis direction.
3.Record the largest value difference as the measurement value.
3.3
Max reversal value
最大反沖值
Position accuracy qualified to ISO 230-2
X
0.006
Y
Z
4.0循圓精度检查Repetition accuracy inspection单位Unit: sec
项
次
NO
检查项目
Inspection item
测试方法图
0.012/300
c.
Y-Z
轴Place
0.012/300
1.7
主轴中心线与床台面之直角度