1. Purpose
目的
The purpose of this inspection standard is to provide a guideline to perform the inspection and judge of the finished product to ensure product quality can meet our customers’ requirement and expectation.
作為品管生產人員,檢驗與判定之標準和依據,以致使生產之產品符合客戶之品質要求.
2. Scope
范圍
Our factory produces desktop keyboard of Japanese.
本廠生產之日语系桌上型鍵盤.
3. Definition:
定義
3.1Major defect: List as rejected of basis, it is to cause the function failure of the keyboard or reduce the using
of the products, some such defects will be rejected by the customer or the end user.
主缺點: 列為批退之依據, 是可能引起鍵盤功能失效或降低產品使用性的缺點, 這樣一些缺點會被客戶或最終用戶拒收。

3.2 Minor defect: May not be reducing the products using or not accord with the standard, but to the products using or
have no influenced to operate. Some such defects might not be rejected by the customer or the end user.
次缺點. 是可能不會減少產品的實際使用性或者不符合標準但對產品使用性或操作無影響的缺點.這樣一些缺點可能不會被客戶或最終用戶拒收.
3.3 Defect definition: This defects including scuffs, shadowing, clouding, discoloration, surface texture
variation, contamination, fine scratching and shininess.
缺陷定義：擦傷、黑點、白斑、異色點、咬花紋異常、髒污、亮點等都可為缺陷.
4. Responsibility
權責
4.1 QA: Perform quality inspection and problem follow up.
品管: 執行品質檢驗，問題追蹤。

.
4.2 ENG: Problem analysis and drafted correction action for any urgent.
工程: 問題分析，應急對策擬定。

4.3 Relevant Dept: Perform relation correction action.
相關部門: 對策執行。

5. Flow chart
NO/無
6. Procedure requirements:
作業內容
6.1Inspection condition and equipments:
檢驗條件与工具：
6.1.1Function test
功能測試.
6.1.2 Cosmetic inspection
外觀檢驗.
I)V iewing angle=45°~90°.
角度: 與產品成45°~90°
II)Viewing distance =30-40cm
距離: 30-40cm
III)Inspection area illumination: 1100－1300LUX
燈光要求：1100－1300LUX
6.1.3 Perform inspection are used the computer , read code of devices , thickness gage , standard Film of
stain , and differ type BOM , ECN,etc. are examined.
利用電腦、讀碼器、厚薄規、污點標准Film,及各機種BOM 、ECN等進行檢驗。

6.1.4 All inspector need to wear gloves or finger.
所有的檢驗人員都需佩戴手套或手指套。

6.2 Sample Plan 抽樣計劃
6.2.1 OBA AQL=0.15
6.2.2 Defect judge standard: Defects divides the Major and Minor . Any defects wouldn’t been
accepted. Details pls reference below explained.
不良判定:不良品分主缺點&次缺點,任何缺點都不可被允收, 具體見下表之標准說明.
7Ref document
參考文件
7.1 Attribute value standard for sample plan/計數值抽樣計劃使用規范
7.2 Final Inspection And Test Procedure/最終檢驗與測試程序
7.3 Engineering Specification DS29-105XX01 工程規格
7.4 Foxconn- Acer KB 外觀檢驗規範
8 Records
使用表單
8.1 OOBA inspection record for Keyboard /Keyboard廠OOBA檢查記錄表
8.2 Serial Number record for finished goods/流水碼之成品抽樣登記表
9 Appendix 附件No/無。