4.點取CANCEL（取消）按鈕,表示不要從磁片存入機器內硬碟機。

File transfer complete.1 files transferredPress NEXT to Continue.File transfer complete. (程式檔案存入到磁片已完成)1 files transferred(一個程式檔案存入到磁片)Press NEXT to Continue. (按NEXT繼續)※因程式檔案多寡,所顯示程式檔案訊息不同8.Save Timing File將目前程式檔案有關時間參數存入到磁片※此功能是將目前生產程式檔案內,有關時間參數存入到磁碟片中,如印刷完一片所需時間、等待時間等等…..1.Load Board載入PC板於中心點位置及視覺系統位置,頂到鋼板位置※Load Board進板指令集是將PC板送進機器內,Z AXIS將會升高到不同高度,當你在下拉式選項Utilities中選擇時,螢幕上會出現手動進板(Manual Load Board)的螢幕如上圖。

1.鋼板高度(Stencil Height)：將PC板上升至鋼板的高度,這是可以查看PC板是否完全密和頂到鋼板及PC板與鋼板有無對位。

2.鏡頭高度(Vision Height)：將PC板上升至視覺影像高度,這是可以查看PC板Mark點是否錯誤。

3.定位工具高度(Tooling Height)：將PC板上升至定位工具高度,這是可以查看PC板吸真空是否定位良好及調整支撐PIN(Support PIN)位置。

4. Begin：開始送板到印刷區位置並依照上述設定上升高度5. Detent：載入PC板向前與向後於中心點位置6. Exit ：跳出手動進板的畫面,回到主畫面2. Stencil Height測PCB板到鋼板厚度This utility will the set STENCIL height.Press NEXT to Continue, or EXIT to Quit.This utility will the set STENCIL height. (要開始使用偵測鋼板高度)Press NEXT to Continue, or EXIT to Quit. (按NEXT繼續, 按EXIT離開)你按NEXT之後，出現下列訊息及視窗：CAUTION, The machine is now going tomove. STAY CLEAR.Press NEXT to Continue, or EXIT to Quit.CAUTION, The machine is now going to(警告,機器現在要移動,內部不能有move. STAY CLEAR.任何東西,需清除)Press NEXT to Continue, or EXIT to Quit. (按NEXT繼續, 按EXIT離開)你按NEXT之後，出現下列訊息及視窗：Press SELECT to JOG the sensor clear ofpaste or stencil apertures,or Press NEXT to CONTINUE.Press SELECT or NEXT to Continue.Press SELECT to JOG the sensor clear of(按SELECT移動偵測感應器,以paste or stencil apertures,免碰到鋼板上錫膏及鋼板上PAD孔)or Press NEXT to CONTINUE. (按NEXT馬上開始在本位置偵測鋼板高度) Press SELECT or NEXT to Continue. (按SELECT 或NEXT繼續)你按SELECT之後，出現下列訊息及視窗：JOG ACTIVE…SQUEEGEE STROKE -112.050Press EXIT to quit.JOG ACTIVE…(移動現在刮刀行程位置)SQUEEGEE STROKE -112.050Press EXIT to quit. (按EXIT離開)你按NEXT與EXIT之後，出現下列訊息及視窗：Locating the board…(載入基板中………)CAUTION：Auto height sensor inprogress. Please wait…(注意：高度自動偵測進行，請稍後………)Stencil height FOUND.Press NEXT to Continus.Stencil height FOUND. (完成偵測鋼板高度)Press NEXT to Continue. (按NEXT繼續下一步驟)3. Set Stroke設定刮刀組行程This utility will allow you to set theSQUEEGEE STROKE used during printing.Press NEXT to Continue, or EXIT to Quit.This utility will allow you to set the (本功能可設定印刷時的刮刀行程) SQUEEGEE STROKE used during printing.Press NEXT to Continue, or EXIT to Quit. (按NEXT繼續, 按EXIT離開) 你按SELECT之後，出現下列訊息及視窗：Jog the SQUEEGEE to the desired ＋STROKE locatedtoward the rear of the stencil.Press NEXT to Continue, or EXIT to Quit.Jog the SQUEEGEE to the desired +STROKE (移動刮刀到朝向鋼板後方located toward the rear of the stencil.的正方向適當位置)Press NEXT to Continue, or EXIT to Quit. (按NEXT繼續, 按EXIT離開) 按NEXT之後，有一指標會往上跑到JOG區的SQUEEGEE STROKE---JOG ACTIVE ---RollTrackball for fine adjust, OR(滾動軌跡球做微調，或是按住SELECT Hold SELECT button and Roll Trackball按鈕並且滾動軌跡球做快速微調) For VELOCITY adjustment.Press EXIT to Leave JOG. (按EXIT離開JOG模式)你按SELECT之後，出現下列訊息及視窗：Jog the SQUEEGEE to the desired －STROKE locatedtoward the front of the stencil.Press NEXT to Continue, or EXIT to Quit.Jog the SQUEEGEE to the desired －STROKE (移動刮刀到朝向鋼板前方located toward the front of the stencil.的負方向適當位置)Press NEXT to Continue, or EXIT to Quit. (按NEXT繼續, 按EXIT離開) 按NEXT之後，有一指標會往上跑到JOG區的SQUEEGEE STROKE---JOG ACTIVE ---RollTrackball for fine adjust, OR(滾動軌跡球做微調，或是按住SELECT Hold SELECT button and Roll Trackball按鈕並且滾動軌跡球做快速微調) For VELOCITY adjustment.Press EXIT to Leave JOG. (按EXIT離開JOG模式)4.Level SqueegeeThis Utility will set the SQUEEGEE height.Press NEXT to Continue, or EXIT to quit.This Utility will set the SQUEEGEE height.(使用測刮刀高度)Press NEXT to Continue, or EXIT to quit. (按NEXT繼續, 按EXIT離開) 按NEXT之後，出現下列訊息視窗：Please install a stencil now.The FRAME CLAMPS will activate whenyou press NEXT.Press NEXT to Continue, or EXIT to quit.Please install a stencil now. (現在請放入鋼板)The FRAME CLAMPS will activate when(按NEXT之後,啟動鋼板固定夾) you press NEXT.Press NEXT to Continue, or EXIT to quit. (按NEXT繼續, 按EXIT離開)按NEXT之後，出現下列訊息視窗：You must now install the squeegee blade.Press NEXT to Continue, or EXIT to quit.You must now install the squeegee blade. (你現在必須安裝刮刀)Press NEXT to Continue, or EXIT to quit. (按NEXT繼續, 按EXIT離開) 按NEXT之後，出現下列訊息視窗：CAUTION, The machine is now going toMove the Z TOWER and cyclethe SQUEEGEE UP and DOWN.Press NEXT to Continue, or EXIT to Quit.CAUTION, The machine is now going to(注意,機器的Z軸和刮刀上下將Move the Z TOWER and cycle會移動)the SQUEEGEE UP and DOWN.Press NEXT to Continue, or EXIT to Quit. (按NEXT繼續, 按EXIT離開) 按NEXT之後，出現下列訊息視窗：Press SELECT to find Stencil Heightor NEXT to Bypass.Press NEXT to Continue, or EXIT to Quit.Press SELECT to find Stencil Height(按SELECT之後,再測一次鋼板高度or NEXT to Bypass.或按NEXT之後,不測鋼板高度)Press NEXT to Continue, or EXIT to Quit. (按NEXT繼續, 按EXIT離開)按NEXT之後，出現下列訊息視窗：Press SELECT to JOG the sensor clear ofpaste or stencil aperturesor press NEXT to CONTINUE.Press SELECT or NEXT to Continue.Press SELECT to JOG the sensor clear of(按SELECT移動偵測感應器,以paste or stencil apertures免碰到鋼板上錫膏及鋼板上PAD孔)or press NEXT to CONTINUE. (按NEXT馬上開始在本位置偵測刮刀高度)Press SELECT or NEXT to Continue. (按SELECT 或NEXT繼續)你按SELECT之後，出現下列訊息及視窗：JOG ACTIVE…SQUEEGEE STROKEPress EXIT to quit.JOG ACTIVE…(移動現在刮刀行程位置)SQUEEGEE STROKE -112.050Press EXIT to quit. (按EXIT離開)你按NEXT與EXIT之後，出現下列訊息及視窗並開始測前後刮刀高度：Leveling front blade.Leveling rear blade.CAUTION：Auto height sensor inprogress. Please wait…(開始偵測刮刀高度。