RoHS CompliantAvisert (2) Type [Avisert (2) 型]• This specification is applicable for CFR 1/8W & MFR 1/8W product only; other product (size), please consult factory for the available specifi-cation and drawing.Remark: P 0 cumulative pitch error 1.0mm/20pitch (P 0 累积脚距误差脚距1.0mm / 20脚距)P 1 to be measured at bottom of clinch (P 1 测量固定端底部)t: ground paper 0.5 ± 0.1mm (t: 纸带底厚 0.5 ± 0.1mm )Avisert (1) Type [Avisert (1) 型]• This specification is applicable for CFR 1/4W & MFR 1/4W product only; other product (size), please consult factory for the available specifi-cation and drawing.Avisert TypeBody diameter 本体直径(D) 2.5 Max.Body length 本体长度(L) 6.8 Max.Lead-wire diameter导线直径(d)0.54±0.05Pitch of component零件间距(P)12.7±1Feed hole pitch孔距(P 0)12.7±0.3Hole center to lead孔心至导线中心测量(P 1) 3.85±0.7Lead to lead distance两脚导线中心测量(F)5±1Tape width纸带宽度(W)18±1Hole position孔位(W 1)9±0.5Lead-wire clinch height导线固定端高度(H 0)16.5 ponent height零件高度(H 1)32.25 Max.Lead wire protrusion导线伸出长度(I)1.0 Max.Feed hole diameter孔径(D 0)4±0.3Total tape thickness纸带总厚(t)0.5±0.2Sticky tape width胶带宽度(W 0)12.5 Min.Uncovered paper tape width纸带露出宽度(W 2)3.0 Max.Height of component from tape center零件至纸带中间的高度(H)17.3 ± 0.5Body diameter本体直径(D) 2.5 Max.Lead-wire diameter导线直径(d)0.54±0.05Pitch of component零件间距(P)12.7±1Feed hole pitch孔距(P 0)12.7±0.3Hole center to lead中心测量(P 1) 3.85±0.7Lead to lead distance两脚导线中心测量(F)5±1Component alignment零件偏移(∆h)0 ± 1Tape width纸带宽度(W)18±1Hole position孔位(W 1)9±0.5Lead wire clinch height导线固定端高度 (H)21.0 Max.Component height零件高度(H 1)32.25 Max.Lead wire protrusion导线伸出长度(I)1.0 Max.Feed hole diameter孔径(D 0)4±0.3Total tape thickness纸带总厚(t)0.5±0.2Sticky tape width热熔胶带宽(W 0)12.5 Min.Uncovered paper tape width纸带露出宽度(W 2)3.0 Max.Length of snipped lead剪脚长度(L)11.0 Max.Hole center to component center孔心至零件中心距离(P 2) 6.35 ± 1.3• 适用于 CFR 1/8W 和 MFR 1/8W 固定电阻。

其它产品的立式加工，可洽询工厂以取得可生产的规格图样。

Max. (最大) Min. (最小)Max. (最大) Min. (最小)UniOhm65RoHS CompliantAvisert (3) Type [Avisert (3) 型]• This specification is applicable for CFR 1/4W , MFR1/4W , MOR 1/4W , MOR1WS, MOR2WS, KNP1WS, KNP2WS product only, other product (size), please consult factory for the available specification and drawing.Avisert TypeAdditional Information (注):1=Avisert 1 Type (型)2=Avisert 2 Type (型)3=Avisert 3 Type (型)Resistance Value (阻值):5% (E-24 series): The 1st digit is “0”, the 2nd & 3rd digits are for the significant figures of the resistance and the 4th indicate the number of zeros following5%产品(E-24系列阻值): 第1位数是0，第2、3位数表示阻值的有效数，第4位表示有几个0; ≤2%(E-24,E-96 series): The 1st digit is “0”, the 2nd & 3rd digits are for the significant figures of the resistance and the 4th indicate the number of zeros following≤2%产品(E-24, E-96系列阻值): 第1-3位数表示阻值的有效数，第4位数表示有几个0Ordering Procedure (Example: MFR 1/8W 1% 50PPM 221Ω T/R-5000 Avisert 3 Type)Remark: P 0 cumulative pitch error 1.0mm/20pitch (注: P0 累积脚距误差1.0mm / 20 脚距)Body diameter本体直径(D)1/8W: 2.0 Max. 1/4W: 2.5 Max.Body length 本体长度(L)1/8W: 4.2 Max.1/4W: 6.8 Max.Body height 本体高度(H)1/8W: 7.0 Max.1/4W: 10.0 Max.Lead wire diameter 导线直径(d)1/8W: 0.45 ± 0.051/4W: 0.54 ± 0.05Pitch of component 零件间距(P)12.7 ± 1Lead to lead distance两脚导线中心测量(F)1/8W: 5 ± 11/4W: 5 ± 1Feed hole pitch 孔距(P 0)12.7 ± 0.3Hole center to lead 孔心到导线中心测量(P 1) 3.84 ± 0.7Component alignment 零件偏移(∆h)0 ± 0.1Paper tape widthc 纸带宽度(W)18 ± 1Hold down tape width 孔至下纸带宽度(W 0)12.5 MinHole position 孔位(W 1)9 ± 0.5Hold down tape position 孔至下纸带位置(W 2)3 Max.Lead wire clinch height 导线固定端高度(H 0)16.5 Max.Length of snipped lead 剪脚长度(H 1)11.0 Max.Lead wire protrusion导线伸出长度(I) 1.0 Max.Feed hole diameter 孔径(d 0) 4 ± 0.3Total paper tape thickness 纸带总厚(t)0.5 ± 0.2Max. (最大) Min. (最小)• 适用于 CFR 1/4W , MFR1/4W , MOR 1/4W , MOR1WS, MOR2WS,KNP1WS, KNP2WS 其它产品的立式加工，可洽询工厂以取得可生产的规格图样。

订购方式 (例如: MFR 1/8W 1% 50PPM 221Ω T/R-5000 Avisert 3型)66UniOhm。