1. 配置OLT接口vlan [H3C]interface Olt 2/0/1[H3C -Olt2/0/1] port hybrid vlan 1 to 4094 tagged (或untagged)2. 创建ONU逻辑接口 [H3C]interface Olt 2/0/1[H3C -Olt2/0/1]using onu 1 to 32 （假设此OLT接口使用了1分32的分光器,）Please wait...Done. [H3C -Olt2/0/1]3. 配置ONU设备MAC地址和ONU逻辑接口绑定 [H3C] interface onu 2/0/1:1[H3C-Onu2/0/1:1] bind onuid 00e0-fc70-2d6d4. 配置ONU逻辑接口为trunk模式 [H3C] interface onu 2/0/1:1[H3C-Onu2/0/1:1] port link-type trunk5. 配置ONU逻辑接口PVID (ONU上行PON口打vlan标签) [H3C] interface onu 2/0/1:1[H3C-Onu2/0/1:1] port trunk pvid vlan 26.配置ONU PON接口的上行带宽 [H3C] interface onu 2/0/1:1[H3C-Onu2/0/1:1] upstream-sla maximum-bandwidth 16007. 配置ONU PON接口的下行带宽 [H3C] interface onu 2/0/1:1[H3C-Onu2/0/1:1] bandwidth downstream max-bandwidth 20008. 配置ONU以太网uni接口的上行带宽 [H3C] interface onu 2/0/1:1 [H3C-Onu2/0/1:1] uni 1 port-policy inbound cir 10249. 配置ONU以太网uni接口的上行带宽 [H3C] interface onu 2/0/1:1 [H3C-Onu2/0/1:1] uni 1 port-policy inbound cir 102410. 配置ONU以太网uni接口端口隔离 [H3C] interface onu 2/0/1:1 [H3C-Onu2/0/1:1] uni 1 port-isolate 11. 配置ONU以太网uni接口打vlan标签 [H3C] interface onu 2/0/1:1 [H3C-Onu2/0/1:1] uni 1 vlan-mode tag pvid 10112. 配置上行GE接口协商模式 [H3C] interface G 2/1/1 [H3C-Gigabit 2/1/1] speed 1000 [H3C-Gigabit 2/1 /1] duplex full13. ONU注册信息显示 [H3C] display onuinfo slot 214. 查询ONU注册、注销命令[H3C] display onu-event interface onu 2/0/8:1 Date Time ONU Event ONU Status 2006/06/28 13:57:03 Registration Up 2006/06/28 13:57:06 Deregist ration Down15. 重启ONU[H3C] interface onu 2/0/8:1 [H3C-Onu2/0/8:1] reboot onu16. 配置设备名称 [H3C]sysname HTSM [HTSM]17. 配置管理接口，管理vlan[H3C]vlan 4 （假设vlan 4 为管理vlan）H3C-vlan3]quit[H3C] interface GigabitEthernet 1/1/1 [H3C –Giga1/1/1]port link-type trunk [H3C –Giga1/1/1]port trunk permit vlan 4 [H3C –Giga1/1/1]quit [H3C]上行接口如果直接接电脑，需要配置上行接口为access模式 [H3C] interface GigabitEthernet 1/1/1 [H3C –Giga1/1/1]port link-type access [H3C –Giga1/1/1]port access vlan 4 [H3C –Giga1/1/1]quit18. 配置设备管理IP地址，网关 [H3C] interface Vlan-interface 4 [H3C -Vlan-interface4]%Oct 14 14:18:59:276 2009 H3C IFNET/4/LINK UPDOWN: Vlan-interface4 001: link status is UP[H3C -Vlan-interface4] ip address 24 %Oct 14 14:19:08:283 2009 H3C IF NET/4/UPDOWN: Line protocol on the interface Vlan-interface4 is UP [H3 C -Vlan-interface4] quit[H3C] ip route-static19. 配置DHCP [H3C] dhcp enable[H3C] dhcp server ip-pool 1[Abiao-dhcp-pool-1] network 24[Abiao-dhcp-pool-1] gateway-list [Abiao-dhcp-pool-1] dns [Abiao-dhcp-pool-1] quit [H3C] interface Vlan-interface 1[H3C -Vlan-interface4] ip address20. 配置OSPF [H3C] ospf[Abiao-ospf-1] area[Abiao-ospf-1-area- network [Abiao-ospf-1-area- area[Abiao-ospf-1-area- network [Abiao-ospf-1-area- quit [Abiao-ospf-1] qui t21. 配置telnet登陆账号及telnet服务 [H3C_OLT_LCGY] telnet server enable % Start Telnet server [H3C_OLT _LCGY][H3C_OLT_LCGY] local-user admin （管理员户） New local user added. [H3C_OLT_LCGY-luser-admin] password simple h3c [H3C_OLT_LCGY-luse r-admin] service-type telnet[H3C_OLT_LCGY-luser-admin] authorization-attribute level 3 [H3C_OLT_LCGY-luser-admin] quit [H3C_OLT_LCGY][H3C_OLT_LCGY] user-interface vty 0 4[H3C_OLT_LCGY_vty_0_4] authentication mode scheme [H3C_OLT_LCGY _vty_0_4] quit [H3C_OLT_LCGY]22. 配置ACL访问控制列表举例：禁止通过ONU1 设备接入的客户端访问Server （ IP 地址为 [H3C] acl number 3000[H3C-acl-standard-3000] rule 10 deny ip source any destination[H3C-acl-standard-3000] quit [H3C] traffic classifier c_1[H3C-classifier-c_1] if-match acl 3000 [H3C-classifier-c_1] quit [H3C] traffi c behavior b_1 [H3C-behavior-b_1] filter deny [H3C-behavior-b_1] quit [ H3C] qos policy p_1[H3C-qospolicy-p_1] classifier c_1 behavior b_1 [H3C-qospolicy-p_1] quit [H3C] interface Onu 1/0/1:1[H3C-Onu1/0/1:1] qos apply policy p_1 inbound23. 配置网管snmp参数 [H3C_OLT_LCGY]snmp-agent[H3C_OLT_LCGY]snmp-agent community read noc-911 acl 2000 [H3C_OL T_LCGY]snmp-agent community write noc-007 acl 2000 [H3C_OLT_LCGY] snmp-agent sys-info version all [H3C_OLT_LCGY]snmp-agent trap enable[H3C_OLT_LCGY]snmp-agent target-host trap address udp-domain para ms securityname security v1 [H3C_OLT_LCGY]24. 创建vlan[H3C_OLT_LCGY]vlan allPlease wait.................................................................... ................ Done. [ H3C_OLT_LCGY]25. 配置在OLT接口上打外层标签功能（QinQ）举例：对于内层标签10，打上外层标签1000 [ProviderA] interface olt 1/0/1[ProviderA-Olt1/0/1] port link-type hybrid[ProviderA-Olt1/0/1] port hybrid vlan 10 1000 tagged [ProviderA-Olt1/0/1] qinq vid 1000[ProviderA-Olt1/0/1-vid-1000] raw-vlan-id inbound 10 [ProviderA-Olt1/0/1 -vid-1000] quit[ProviderA] interface gigabitethernet 1/1/1[ProviderA-GigabitEthernet1/1/1] port link-type trunk [ProviderA-GigabitE thernet1/1/1] port trunk permit vlan 100026. 保存配置[H3C_OLT_LCGY]quit <H3C_OLT_LCGY>saveThe current configuration will be written to the device. Are you sure? [Y/ N]:yPlease input the file name(*.cfg)[flash:/startup.cfg](To leave the existing filename unchanged, press the enter key): Validati ng file. Please wait...............Saved the current configuration to mainboard device successfully. Confi guration is saved to device successfully. <H3C_OLT_LCGY>27. ONU 4 端口对上行报文打上同样vlan标签，且进行vlan隔离配置# interface Onu2/0/1:1bind onuid 0023-8971-edf3uni 1 port-isolateuni 2 port-isolateuni 3 port-isolateuni 4 port-isolateport link-type trunkport trunk pvid vlan 228. ONU升级命令[ProviderA] interface olt 1/0/1[ProviderA-Olt1/0/1] update onu filename file.app。