Henan Hongji MineMachinery Co.,LTD900 Cone Crusher PYB900本使用说明书用于PYB900标准型，PYZ900中型，PYD900短头型圆锥破碎机。
This operating manul can be applied to PYB900 standard, PYZ900 medium, PYD900 short head cone crusher.一、T he purpose of the machine(机器的用途)900圆锥破碎机广泛应用在冶金工业、建筑工业、化学工业及硫酸盐厂业中，适用于破碎中等和中等以上硬度的各种矿石和岩石，如：铁矿石、铜矿石、石灰石、石英、花岗岩、砂岩等。
Φ900 cone crusher is widely used in metallurgical industry, building industry, chemical industry and sulfate plant industry, and it is suitable for crushing all kinds of ores and rocks of medium hardness and medium above , such as: iron ore, copper ore, limestone, quartz, granite, sandstone, etc.二、Technical parameters(技术性能)型号Model 基本参数basic parameterPYB900标准型圆锥破碎机The standard modelPYZ900中型圆锥破碎机The medium modelPYD900短头型圆锥破碎机The short head model破碎锥直径mmDiameter of cone crusher900 900 900 给矿口宽度Feeding size mm 135 70 50 推荐最大给矿块尺寸Max.feeding size mm115 60 40 排矿口调整范围Adjusted scopeof discharging mm15-50 5-20 3-13 产量Capacity t/h 50-90 20-65 15-50 偏心套转速Rotation ofEccentric r/min333 333 333 弹簧总压力Pressure of Springt70 70 70 立轴摆动次数Spindle number ofswing r/min300 300 300电机型号Model Y315S-8 Y315S-8 Y315S-8 电压Voltage v 220/380 220/380 220/380转速Rotation r/min 740 740 740机器总重Total weight of whole10177 10186 10264 machine kg外形尺寸Dimensions（L×W ×H）3050×1640×2350 3050×1640×2350 3050×1640×2350 mm订货须知Remark：订货时应在合同中注明产品类型。
You should remark clearly which model you buy in the contract.PYB900 Henan Hongji Mineφ900 Cone Crusher三、外形图PYB900 Henan Hongji Mine900 Cone Crusher四、机器的结构和组成 The structure and composition of the machine1、圆锥破碎机工作时，电动机通过弹性联轴器，传动轴和一对锥齿轮带动偏心轴套转动，破碎圆锥心线在偏心套的适动下做旋摆运动。
使破碎壁和扎臼壁时而靠近，时而远离，矿石在碎腔内不断的受到积压与冲击，而被破碎。
When it works, the motor driven eccentric sleeve rotates through flexible coupling, drive shaft and a pair of bevel gear , crushing cone center line makes spin pendulum movement under the proper action of the eccentric sleeve . So the broken wall and rolling acetabular wall sometimes close, sometimes far away, ore constantly being extrusion and impact, and was broken in the crushing cavity .2,该机由机架、传动轴、偏心套、碗形轴承、破碎圆锥、支承套、调整套、进料、弹簧、弹性联轴器、润滑、电器等部分组成。
The machine consists of frame, transmission shaft, eccentric, bowl bearing, crushing cone,supporting sleeve, adjusting sleeve, feed, springs, flexible couplings, lubrication, electrical and other parts五、机器的安装 Installation of the machine1、安装圆锥破碎机的厂房内，需有起重设备，以便在机器安装、维修时使用。
起重机的起重能力可按表2选择。
The workhouse ,being installed cone crusher, needs for lifting equipment ,which can used during the process of installation and maintenance. The capacity of Crane can selected according to Table 2表22、圆锥破碎机地基图如图1所示，该地基图供参考，用户可根据具体情况进行设计。
Foundation shown in Figure 1, it just for reference, the user can be designed according to specific circumstances.名 称 name重 量（kg ）起 重 application机 架frame2300Installationcrushing cone 1300 Installation andmaintenance adjusting sleeve 1200Installation and maintenancebowl bearing 400Installation andmaintenance eccentric 400 Installation andmaintenance4、为了基础不受损坏，在基础上部，必须覆盖护板，该件由用户自备。
In order to avoid damage the upper space of foundation must covered by guard ,which supplied by the user5、润滑系统和电气操作的位置，用户可按具体情况改变位置，使其顺序不得变动。
The location ofthe lubrication systems and electrical operation can be changed under specific circumstances.But it may not change its order.PYB900Henan Hongji Mine900 Cone Crusher图1 地基图PYB900 Henan Hongji Mine900Cone Crusher6、6、机架得安装（图2）The installation of the frame（1）安装机架时，在地脚螺栓附近用8～12组垫板，楔铁支撑调整其水平度和垂直度，水平度以机架的环行加工面为基准，用水平仪测量其偏差不大于0.1毫米/米，垂直度以机架的衬套中心为基准，用悬锤法测量。
When installing the frame, 8 to 12 groups of pallets must be used near the anchor bolt, wedge support its horizontal and vertical adjustment, level degrees marked by the rack ring machined surface, measure the deviation of a level no greater than 0.1 mm / m, vertical rack bushing to the center as a reference measurement method netsuke.（2）机架调整紧固后，将垫板组焊在一起，以免窜动。
After adjusting frame, in order to avoid moving ,the plate must be compound together.（3）待设备全部安妥之后，进行第二次浇注。
After all equipment soundness, make the second pouring（4）保持机架的水平性，能保证机器可能的工作否则易使衬套局部磨损而影响主轴和水封装置工作不正常。
keeping the level of frame can guarantee the machine can work otherwise it can easily to make the liner partial abrasion and impact the spindle and water seal device not work properly.图2 Drawing of installation of framePYB900 Henan Hongji Mine900 Cone Crusher7、传动轴的安装 The installation of the drive shaft（1）安装传动轴时，应在机架与传动轴的凸缘之间垫上垫片，如图3所示。