Change Screen
Change Tooling
Down Exit Down Exit
Change
Exit
language
取出钢网
• 按Open Cover
Run
Open Cover
Paste Load
Clean Adjust
Screen
• 按Change Screen
Setup monitor
Data Data Squeegee Screen Tooling Language
MARK识别(1)
• 將印刷模式选为Step. • 在主菜单中,按Run
Run Open Paste Clean Cover Load Screen
• 按Auto Board
Auto Manual Board Board
MARK识别(6)
• 调好后按Learn Fiducial
Learn Fiducial
Next Previous Incr.
Decr.
Exit
• 按Exit
Learn Fiducial
Next Previous Incr.
Decr.
Exit
• 按Locate Fiducial
Learn Locate
Mode Load Edit
Setup Change Change Change Exit
Data Data Squeegee Screen Tooling Language
• 选好后,按Exit ,退回主菜单.
Mode Load Edit
Setup Change Change Change Exit
Step
Reset
• 如果MARK点位置偏移较多,可按Adjust调整 MARK点坐标.
• 如果画面上找不到识别点,可通过Search Step手动寻找识别点,直至找到为止.如果错 过,可按Search Reset搜寻位置复位.
• 如识别点位置尚可,则按Fiducial Setup,进入 以下画面.
Incr.
Exit
Decr.
Exit
MARK识别(7)
• 按Step
Step Open Fiducial Adjust Search Search Single
Exit
Cover Setup
Step
Reset
• 同理,重复之前设置MARK部分操作.
• 将两个PCB识别点及其钢网识别点核对OK后, 按Step.
Paste Load
•打开前盖
Clean Screen
Adjust Setup monitor
•放入钢网
•盖上前盖
•按亮‘系统键’
•按Change Screen
CHANGE SCREEN
BOARD CLAMPS
•按Exit ,退回主菜单
CHANGE SCREEN
BOARD CLAMPS
PRIME PAPER
Print
Exit
Height
• 放入顶针
• 放入钢网
• 关上前盖
• 按亮‘系统键’
换顶针(2)
• 按Home Cleaner
Adjust Open Home Cover Cleaner
• 按Exit
Board Stop
Full Width
Load Width
Print Exit Height
Adjust Open Remove Board Cover Cleaner Stop
Edit
Setup
Change
Data Squeegee Screen
Change Tooling
Change Exit Language
编程(3)
编程(4)
调程序
• 在主画面,按Setup
Run
Open Cover
Paste Load
Clean Screen
Adjust
Setup monitor
maint
• 按Load Data
Mode
Load Data
Edit Data
Setup Squeegee
Change Screen
Change Tooling
Step Open Fiducial Adjust Search Search Single
Exit
Cover Setup
Step
Reset
• 出现‘Saving Fiducial Data-Please Wait
Board data file saved’,按Exit.
Step
Single
Exit
• 裝回钢网
换钢网纸(2)
• 关上前盖 • 按亮‘系统键’
• 按Change Screen
CHANGE SCREEN
BOARD CLAMPS
PRIME
PRIME
Exit
PAPER SOLVENT
• 按Exit,退回主菜单
CHANGE SCREEN
BOARD CLAMPS
PRIME
PRIME
Exit
Mode Load Edit
Setup Change Change Change Exit
Data Data Squeegee Screen Tooling Language
加锡膏(1)
• 按Paste Load
Run
Open Cover
Paste Load
Clean Screen
• 按Manual Load
• 将接受分数Accept Score调成600.(当机器MARK点的分 数小于该接受分数时将报警,不能印刷.该接受分数可 根据实际情況下更改)
• 按Learn Fiducial进入画面右上方编辑栏MARK尺寸.如 MARK点为圆形,则尺寸为直径Diameter,如为方形,则尺 寸宽Fiducial Width,高Fiducial Height.
MARK识别(4)
MARK识别(5)
Learn
Locate
Set Next Previous Incr.
Decr.
Exit
Fiducial Fiducial Light
• 将MARK 点类型Fiducial Type调成相应的形状,圆形 Circle,或方形Rectangle.
• 將MARK背景Background调成相应的黑色Dark,或白色 Light.
Set
Next Previous Incr.
Decr.
Exit
Fiducial Fiducial Light
• 如分數符合要求,則按Exit.(否則須重新調整參數)
Locate Fiducial
• 按Exit
Learn
Locate
Fiducial Fiducial
Set Light
Next Previous
• 按Change Screen
Setup
monitor
maint
CHANGE BOARD SCREEN CLAMPS
PRIME
PRIME
Exit
PAPER SOLVENT
• 出現‘Open Front Cover and Remove
Screen’
• 打开前盖
• 取出钢网
• 取出旧钢网纸
• 裝好新钢网纸
板时间). • Front Print Speed前印刷速度 • Rear Print Speed后印刷速度
主画面的识别(3)
• Front Pressure 前刮刀压力 • Rear Pressure 后刮刀压力 • Separation Speed 分离速度 • Clean 1 Count Rate:1/2 • 擦拭频率为每刷两块 PCB擦一次钢网,現在已刷了
• 按Exit.
MARK识别(8)
Auto Manual
Exit
Board Board
编程
编程(2)
• 在主画面,按Setup.
Run Open Paste Clean Adjust Setup monitor Cover Load Screen
• 按Edit Data
maint
Mode Load Data
maint
CHANGE BOARD
PRIME
PRIME
Exit
SCREEN CLAMPS
PAPER
SOLVENT
• 出現‘Open Front Cover and Remove
Screen’
• 打开前盖
• 取出钢网
• 关上前盖
• 按亮‘系统键’
•按Open Cove换r 上钢网
Run
Open Cover
PRIME PRIME PAPER SOLVENT
maint Exit
改变印刷模式
• 在主画面,按Setup.
Run Open Paste Clean Adjust Setup monitor maint Cover Load Screen
• 按Mode,使主画面左上角的Mode在Auto,No Print,Single,Step中轮换.
Print
Exit
Directn
安裝与清洗刮刀
• 在取出钢网的时候,松开固定刮刀的兩個螺丝 即可取出刮刀.
• 应松开锡膏挡片以对刮刀进行彻底清洁. • 旋紧螺丝时应注意避免螺丝滑丝. • 安裝刮刀时应保持两边平衡. • 轻拿轻放,避免损坏刮刀.
换钢网纸(1)
• 按Open Cover
Run Open Paste Clean Adjust Cover Load Screen