设置VTP domain(核心、分支交换机都设置)Switch>enSwitch#config tSwitch(config)#hostname switch-hxswitch-hx(config)#exitswitch-hx#vlan dataswitch-hx(vlan)#vtp domain comswitch-hx(vlan)#vtp serverswitch-hx(vlan)# exitswitch-hx#copy run startSwitch>enSwitch#config tSwitch(config)#hostname switch-fz1switch-fz1(config)#exitswitch-fz1#vlan dataswitch-fz1(vlan)#vtp domain comswitch-fz1(vlan)#vtp clientswitch-fz1(vlan)#exitswitch-fz1#copy run startSwitch>enSwitch#config tSwitch(config)#hostname switch-fz2switch-fz2(config)#exitswitch-fz2#vlan dataswitch-fz2(vlan)#vtp domain comswitch-fz2(vlan)#vtp clientswitch-fz2(vlan)#exitswitch-fz2#copy run startSwitch>enSwitch#config tSwitch(config)#hostname switch-fz2switch-fz4(config)#exitswitch-fz4#vlan dataswitch-fz4(vlan)#vtp domain comswitch-fz4(vlan)#vtp clientswitch-fz4(vlan)#exitswitch-fz4#copy run startSwitch>enSwitch#config tSwitch(config)#hostname switch-fz5Switch-fz5(config)#exitSwitch-fz5#vlan dataSwitch-fz5(vlan)#vtp domain comSwitch-fz5(vlan)#vtp clientSwitch-fz5(vlan)#exitSwitch-fz5#copy run start将端口设置为trunk端口switch-hx>enswitch-hx#config tswitch-hx(config)#int g0/1switch-hx(config-if)#switchport mode trunk switch-hx(config-if)#exitswitch-hx(config)#int g0/2switch-hx(config-if)#switchport mode trunk switch-hx(config-if)#exitswitch-hx#copy run startswitch-fz1>enswitch-fz1#config tswitch-fz1(config)#int g1/1switch-fz1(config-if)#switchport mode trunk switch-fz1(config-if)#exitswitch-fz1(config)#int f0/1switch-fz1(config-if)#switchport mode trunk switch-fz1(config-if)#exitswitch-fz1(config)#int f0/2switch-fz1(config-if)#switchport mode trunk switch-fz1(config-if)#endswitch-fz1#copy run startswitch-fz2>enswitch-fz2#config tswitch-fz2(config)#int f0/1switch-fz2(config-if)#switchport mode trunk switch-fz2(config-if)#endswitch-fz2#copy run startswitch-fz3>enswitch-fz3#config tswitch-fz3(config)#int f0/1switch-fz3(config-if)#switchport mode trunk switch-fz3(config-if)#endswitch-fz3#copy run startswitch-fz3#switch-fz4>enswitch-fz4#config tswitch-fz4(config)#int g1/1switch-fz4(config-if)#switchport mode trunk switch-fz4(config-if)#exitswitch-fz4(config)#int f0/1switch-fz4(config-if)#switch mode trunk switch-fz4(config-if)#endswitch-fz4#copy run startswitch-fz4#switch-fz5>enswitch-fz5#config tswitch-fz5(config)#int f0/1switch-fz5(config-if)#switchport mode trunk switch-fz5(config-if)#endswitch-fz5#copy run startswitch-fz5#在核心交换机上建立VLANswitch-hx(vlan)#vlan 10 name aaaVLAN 10 added:Name: aaaswitch-hx(vlan)#vlan 11 name bbbVLAN 11 added:Name: bbbswitch-hx(vlan)#将交换机端口划入VLANswitch-fz1>enswitch-fz1#config tswitch-fz1(config)#int f0/3switch-fz1(config-if)#switchport access vlan 10 switch-fz1(config-if)#exitswitch-fz1(config)#int f0/4switch-fz1(config-if)#switchport access vlan 11 switch-fz1(config-if)#endswitch-fz1#copy run startswitch-fz2>enswitch-fz2#config tswitch-fz2(config)#int f0/3switch-fz2(config-if)#switchport access vlan 10 switch-fz2(config-if)#exitswitch-fz2(config)#int f0/4switch-fz2(config-if)#switchport access vlan 11 switch-fz2(config-if)#endswitch-fz2#copy run startswitch-fz2#switch-fz3>enswitch-fz3#config tswitch-fz3(config)#int f0/3switch-fz3(config-if)#switchport access vlan 10 switch-fz3(config-if)#exitswitch-fz3(config)#int f0/4switch-fz3(config-if)#switchport access vlan 11 switch-fz3(config-if)#endswitch-fz3#copy run startswitch-fz3#switch-fz4>enswitch-fz4#config tswitch-fz4(config)#int f0/3switch-fz4(config-if)#switchport access vlan 10switch-fz4(config-if)#exitswitch-fz4(config)#int f0/4switch-fz4(config-if)#switchport access vlan 11switch-fz4(config-if)#endswitch-fz4#copy run starswitch-fz5>enswitch-fz5#config tswitch-fz5(config)#int f0/3switch-fz5(config-if)#switchport access vlan 10switch-fz5(config-if)#exitswitch-fz5(config)#int f0/4switch-fz5(config-if)#switchport access vlan 11switch-fz5(config-if)#endswitch-fz5#copy run startswitch-fz5#配置三层交换switch-hx>enswitch-hx#config tswitch-hx(config)#int vlan 10upswitch-hx(config-if)#ip add 192.168.91.254 255.255.255.0switch-hx(config-if)#exitswitch-hx(config)#int vlan 11switch-hx(config-if)#ip add 192.168.92.254 255.255.255.0switch-hx(config-if)#三层交换机默认已启动路由，ip routing命令可暂时不用，如路由被关掉，可用此命令。