电子行业专业英语词汇 Document number：WTWYT-WYWY-BTGTT-YTTYU-2018GT专用词汇表一、生产流程 1.插机(刮蓝胶)component- inserting2. 装配 assembly3. 修理repair4. 包装 packaging5. 成品仓 finished goods warehouse6. 返工 rework7. 啤胶件8. 组件成型 component moulding9. IC 烧录 IC program 10. 插件 insection 11. 注塑 plastic injection 12. 发料 material delivery 13. 插机14. 零件加工 component-processing 15. 炉前外观检查 visual inspectionbefore wave soldering16. 电源板波峰焊 power board wavesoldering17. 执锡18. 零件后焊 hand soldering 19. 零件焊接&打黄胶20. 低电压测试 low voltage test 21. 半成品外观检查Semi-finishedgoods visual inspection22. 过水洗机 23. 打热熔胶 dotting hot glue 24. 装卡板25. pallet 栈板 26. IC 烧录 IC program 27. SMT(刮锡膏)28. 喷油 spray conformal coating 29. 焗干防水油 30. welding 焊接 31. breathing 排气 32. feed 供料 33. Tiana 天那水34.to load material上料 to unloadmaterial卸料 to returnmaterial/stock to退料35.to fix a die装模 to take apart adie拆模36.cold forging 冷锻 press forging 冲锻37.to impose lines压线38.to compress, compressing压缩39.焗炉温度40.开槽groove41.shearing剪断42.接线端子 terminal43.to stake, staking, reviting铆合44.fuse together熔合45.electrical sparkle电火花46.fit together组装在一起47.fasten锁紧(螺丝)48.rotating speed, revolution转速49.argon welding氩焊50.to take apart a die卸下51.to load a die装上52.to tight a bolt拧紧螺栓 to loosera bolt拧松螺栓pound die复合模54.punched hole冲孔55.buffing 抛光56.chamfering machine 倒角机57.panel board镶块58.to cutedges=side cut=side scrap切边59.to pull, to stretch拉伸60. Line streching, line pulling线拉伸61.engraving, to engrave刻印62.degrease脱脂63.rinse水洗64.pierce die冲孔模65.forming die成型模66.progressive die连续模67.gang dies复合模68.shearing die剪边模69.riveting die铆合模70.pierce冲孔71.forming成型(抽凸,冲凸)72. draw hole抽孔73.吹热缩管74.胶芯plastic core二、夹具设备、工具75.烙铁 iron76.排气扇 A exhaust fan77.稀释剂 a tinner78.水洗锡线79.pallet栈板80.gunk 料斗81.caliper gauge 卡规82.Screw driver起子83.barcode scanner条码扫描器84.热风枪 hot air reflowing gun 85.taker取料机86.roller 滚筒 runner 流道87.plastic basket胶筐88.isolating plate baffle plate;barricade隔板89.steel plate钢板90.roll material卷料91.conveyer belt输送带92.transmission rack输送架93.钢网 stencil94.油墨 printing ink95.插机并过炉96.高压测试 hi-pot test97.铣刀 milling cutter98.发热管 heater99.烙铁咀 iron tip100.静电手套 ESD gloves 101.风枪 air gun102.p unch冲头103.g roove punch压线冲子104.a ir vent排气道105.w elding line熔合痕106.C ONN Connector 连接器107.C AV Cavity 模穴108.A SS'Y Assembly 装配,组装109.继电器relay110.磨床切割片111.延时器 delay timer112.热电偶Heat control sensor 、thermocouple113.电磁阀Solenoid114.温控器Temperature control 115.烙铁发热芯heater core for iron 116.剪钳 wire cutter117.电批开关Electric screw driver switch118.电批Electric screw driver 119.电批齿轮Electric screw driver gear 120.火牛transformer121.碳刷Carbon brush122.吸锡泵suck solder pump123.尖嘴钳micro long nose pliers 124.热熔胶枪glue gun125.热风筒heating gun126.f use machine热熔机127.烙铁座iron seat128.静电带wrist strap129.波峰锡炉wave soldering oven 130.水循环系统water-recyclingsystem131.水洗机132.防水油 conformal coating133.自动成型机 auto-moulding machine 134.电晶体自动成型机135.螺丝泵 screw pump136.恒温运风焗炉137.手浸锡炉138.剪脚机139.超声波蒸水机140.表面组件拾放机141.高周波塑料熔接机142.半自动锡浆印刷机143.剪线机144.超声波啤机ultrasonic welding machine145.自动绕线机146.超声波清洗机 ultrasonic cleaning machine147.振动试验台vibration testplatform148.计算机剥线机electronic wire-peeling machine149.贴片机 SMT equipment150.供料器 feeder151.红外焗炉152.封黑胶预热炉153.回焊炉温度曲线测试仪154.焗炉155.进料器车156.锡浆搅拌机157.无铅波峰焊机158.开线机159.封口机160.胶纸机161.移载装置162.送板机163.周转车164.发电机electric generator 165.注塑机 plastic injection machine 166.碎料机smashing machine 167.干燥机drier168.自动吸料机auto-sucking machine 169.锯床170.车床lathe171.钻床172. punching machine 冲床173.干燥机 drier174.冷水机 cooler175.数控精密火花机176.移印机 printer177.手动吊机178.热油机oil-heating machine 179.叉车forklift180.磨床grinder181.铣床miller182. sheet metal parts 冲件183. punching machine 冲床184.过滤器 filter185.碎料干燥机186.抽湿机187.热风回焊炉 hot air reflowsoldering oven188.注塑机plastic injeciton machine 189.润滑油grease190.汽缸Rmulti cylinder191.螺丝screw 192.弹簧spring193.蜂鸣器buzzle194.刮刀 squeegee195.真空杯vacuum cup196.真空咀vacuum tip197.喷嘴Nozzle198.支架bracket199.六角板手200.过滤器Filter201.密封圈 airproof ring 202.套筒/活塞piston203.顶针thimble204.传输皮带belt/conveyor 205.真空棉?pad vacuum 206.消音器muffler207.滑轮Pulley,idler tension,asy pre-tension208.夹片Replacement Fine Foil 209.线夹wire clamp210.扎线 tie wrap211.通风孔 blowhole212.自功螺丝 self-tapping screw 213.保险丝Fuse214.高度规High dividers215.螺线管solenoid216.送/扯线螺线管Spring solenoid assembly217.焊咀gaiser218.电源线Power cord219.测试针test probe220.变压器transformer221.弹性定位柱spring fixation pole 222.铝皮sheet aluminum 223.网络线communicate wire 224.电磁阀Solenoid AIRTAC 225.精调电阻Precision adjustable resisto226.脚踏开关foot switch227.开关电源switching power 228.散热片Thermal Conductive Pad 229.旋转开关Rotary switch 230.接线柱Pole Wiring231.音频插头Audio plug232.按键开关keyswitch233.保险丝座Fuse jack234.定位柱fixation pole235.ICT压棒ICT-PRESSINGSTICK236.除泡剂Defoamer237.继电器Relay238.电线束electrical wiring harness 239.锡箔纸Solder foil papper 240.针筒needle canister241.光电开关Photoelectricity switch 242.电批Electric screw driver 243.烙铁soldering iron244.黄油（润滑油）butter(lubricant)245.气管wind pipe246.刀片blade247.bolt螺栓248.trailer=long vehicle拖板车249.stopper阻挡器250.flow board流水板251.v accum cleaner吸尘器252.quenching淬火253.tempering回火254. annealing退火255.volatile挥发性256.风批Pneumatic driver257.电批Electric screw driver三、质量管理QC : quality control 质量管理258. IQC : incoming quality control 进料质量管理259..OQC : output quality control 出货质量管理260.PQC : process quality control 制程质量管理也称261.I PQC: in process quality control. 262.AQL : acceptable quality level 允收标准263.CQA: customer qualityassurance 客户质量保证264.PPM Parts Per Million 百万分之一265.MA : major defect 主要缺点MI : minor defect 次要缺点266.CR :critical defect 关键缺点267.SMT : surface mountingtechnology 表面粘贴技术268.SMD : surface mounting device 贴片机269.SMC : surface mountingcomponent 表面粘贴组件270.ECN : engineering change notice 工程变更通知271.D CN : design change notice 设计变更通知272.BOM : bill of material 物料清单-STD-105E : 美国陆军标准,也称单次抽样计划.274. NG :Not Good 不行,不合格275.ESD Electry-static Discharge 静电排放276.5S 希腊语整理,整顿,清扫,清洁,教养277.Polarity : 电性/极性 Icicles : 锡尖278.Non-wetting : 空焊279.burr 毛刺，批锋280.locking knot 死结281.t orsion 扭曲282.warpage 翘曲283.waviness 波痕284. flying 飞件285.blister 起泡286.Short circuit : 短路287.冷焊 cold soldering288.non-welding 289.假焊290.包焊291.焊点292.lifted solder 浮焊293.pseudo soldering 虚焊294. open soldering脱焊295.Splay mark?水纹296.icicle/solder projection拉尖297.Flow mark?流纹298.White patches on surface?表面白斑299.Sink marks?缩影300.Mold release?脱模301.焊盘 soldering tray 302.Missing component : 缺件303.Wrong component : 错件304. Excess component : 多件305.Insufficient solder : 锡少306.Excessive solder : 锡多307.Solder residue : 锡渣308.Solder ball : 锡球309.Tombstone : 墓碑310.b reaking.(be)broken,(be)cracked 断裂311.Sideward : 侧立312.c osmetic defect外观不良313. mixed color杂色314. die repair模修315. rust生锈316. grease/oil stains油污317. delamination起鳞318. gouge沟槽;凿槽319. inclusion杂质320. poor staking铆合不良321. oxidation 氧化322. abrasion磨损323.reverse angle = chamfer倒角324. failure, trouble故障325.dents压痕326.defective upsiding down抽芽不良327.defective to staking铆合不良328.embedded lump镶块329.feeding is not in place送料不到位330.stamping-missing漏冲331.e xcessive gap间隙过大332.burr(金属)flash(塑件)毛边dewed=moldy=mouldy发霉334. slipped screw head & slippery screw head螺丝滑头335.slipped screwhead/shippery screw thread滑手336.speckle斑点337.dimension/size is a little bigger 尺寸偏大(小)338.not up to standard不合规格 out of specification339.shrinking/shrinkage缩水340.mixed color杂色341.d iscoloration异色342.ageing 老化343.hardening 硬化344. overheating 过热345.rust prevention 防蚀346.tempering 回火347.water spots水渍348.exposed metal/bare metal金属裸露ck of painting烤漆不到位ponent damage : 零件破损351.G old finger : 金手指352.SOP : standard operationprocess 标准操作流程353.SIP : standard inspectionprocess 标准检验流程354. Simple random sampling : 简单随机抽样355.SPC : Statistical processcontrol 356.SQE : Supplier qualityengineering357.Sampling sample :抽样计划358.fixture : 治具359.Gauge 量规360.QTS: Quality tracking system 质量追查系统361.S pare parts :备用品362.Inventory report for : 库存表363.Manpower/Tact estimation 工时预算364. Calibration : 校验365.Corrugated pad : 波纹垫366.Conductive bag : 保护袋367.Fixture : 制具368.Probe : 探针369.Lint-free gloves : 静电手套370.Wrist wrap : 静电手环371.p lug hole孔塞372.Wrong direction 极性反ponent damage or broken 零件破损374. Unmeleted solder熔锡不良375.flux residue松香残渣376.wrong label or upside down label 贴反377.mixed parts机种混装378.poor solder mask绿漆不良379.氧化 Oxidization380.刮花 Scratch381.脏污Contamination382.变形 Deformation 383.stand off height浮高384. IC reverse IC反向385. supervisor课长386.Forman组长387.PPM: Parts per million 不良率388.DPU: Defects per unit 单位不良率389.Resistor: 电阻390.Capacitor:电容391.R esistor array : 排阻392.Capacitor array: 排容393. DIODE: 二极管394.triode: 三极管395.Crystal:震荡器396.Fuse:保险丝397.Bead: 电感 inductor 398.Connector:连结器399.Metal Shearing:裁剪400.ERP: Enterprise Resource Planning 企业资源规划401.P rocessed material: 流程性材料402.Corrective action:纠正措施403. Preventive action:预防措施404.PDCA:Plan/Do/Check/Action计划/实施/检查/处理405.Oscillator:振荡器406.Adapter: 适配器407.Spindle:轴心408.WIP: Work in process半成品Waive:特别采用409.FMEA:Protentical Failure Mode and Effects Analysis失效模式与效应分析410.M SA: Measurement SystemsAnalysis 量测系统分析411.Benchmarking:竞争标竿412. Roka Yoke 防错法413. Mistake Proofing 防呆法414. Fool-Proof System防呆系统415. Specified Requirement:规定要求416. AOQ: Average Outgoing Quality 平均检出质量 AOQL: AverageOutgoing Quality Limit 平均检出质量界限417. Benchmarking 基准点418. Calibration 校准419. Continuous improvement 持续改进420. Deviation / Substitution 偏差/ 置换421.ESD: Electrostatic discharge 静电释放422.FMEA: Failure Mode Effect Analysis 失误模式效应分析423. First Article approval 产品的首次论证424.First pass yield 一次性通过的成品率425.First sample inspection 第一次样品检验426.FMECA: Failure mode effect and critically analysis 失误模式,效应及后果分析427.Life Testing 寿命试验Lot traceability 批量可追溯性428.NONCONFORMANCE 不符合429.OUT-OF-CONTROL PROCESS 失控工序430.Pilot Application 试产(试用) 431.P PM: Parts per million 百万分之一432.Process capability index 工序能力指数433. Total quality management 全面质量管理434.Site Audit 现场审核435.Failure rate percentage 失误百分率436.Customer complaints 客户投诉437.Root cause analysis of failures 失误根原分析yout Inspection:全尺寸检验439.Bulk material:散装材料440.Feasibility Reviews:可行性审查441.P re-launch:量产前442.Stock rotation :存货周转443. Inventory levels:最低库存量444.Interim action:临时措施445.Permanent action:永久措施446.vibration test振动试验447.Conveyer流水线物料板448.fasten锁紧(螺丝) 449.fuse machine热熔机450.SOP制造作业程序451.w ork cell工作间452.trolley台车453. carton纸箱454.电阻 Resistor455.电容 Capacitor456.晶振 Crystal resonator 457.开关 Switch458.插座 Jack459.插头 Plug460.工艺 Workmanship 461.喷油 Conformal coating 462.插件Insertion481.C TQ=critical to quality 463.回焊炉 Reflowing oven464.飞达 feeder465.吸嘴466.钢网 Stencil467.抛料468.线股Strand469.松香 Flux470.尾数 WP471.锡炉 DIP472.暂置 Hold473.全检 Sorting474.条形码 Bar code475.日期编码 Date code476.标准作业指导书 SOP Standardoperation plan477.过电压保护 OVP Over voltageprotect478.汶波/噪声Noise479.连接器Connector480.线材 Cable。