实际
测量值
Measured value
床台X轴方向运动之真直度
Straightness of the X axis movement
a.
X-Z台Y轴方向运动之真直度
Straightness of the Y axis movement
a.
X-Z
面内
1000
b.
Y-Z
面内
1-1
the table 300 mm in X-axis direction.
the largest value difference as the measurement value.
300
旋转台旋转偏摆
Table runout(XY)
300
旋转台旋转偏摆
Table runout(Z)
车刀角度换刀後重复定位精度
核准者
CONFIRMED
检验者
CHECKED
检验
日期
DATE
MCV F01 S001
Q3 940331-7
静态精度STATIC ACCURACY INSPECTION单位Unit : mm
项
次
NO
检查项目
Inspection item
测试方法图
Measuring method diagram
许可差
Permissible deviation
to get reading at both ends of the straight edge.
the table 300 mm in X-axis direction.
the largest value difference as the measurement value.
300
床台Y轴方向运动之直线度
加工中心精度检验规范
NO.
ˉˉˉ
日沛电脑配件（上海）有限公司
RIPEIcomputeraccessory(Shanghai) Co., Ltd.
加工中心精度检验规范
机型：
机号：
SERIAL NO.
中国上海松江区新桥镇申港路3636号
Shenggang Road,Xin Qiao Songjiang Shanghai China
单位Unit : mm
项
次
NO
检查项目
Inspection item
测试方法图
Measuring method diagram
许可差
Permissible deviation
实际
测量值
Measured value
各轴方向相互运动之直角度
Perpendicularity Between movement in X axis direction and Y axis direction and Z axis direction
单位Unit : mm
项
次
NO
检查项目
Inspection item
测试方法图
Measuring method diagram
许可差
Permissible deviation
实际
测量值
Measured value
床台X轴方向之运动与其上面之平行度
Parallelism between movement in X axis direction and table upper surface
X≦500
500＜X≦800
800＜X≦1250
1250＜X≦2000
床台Y轴方向之运动与其上面之平行度
Parallelism between movement in Y axis direction and table upper surface
Y≦500
500＜Y≦800
800＜Y≦1250
1250＜Y≦2000
a.
X-Y
轴Place
300
b.
X-Z
轴Place
300
c.
Y-Z
轴Place
300
主轴中心线与床台面之直角度
Perpendicularity between centerline of main spindle and table surface.
旋径每300
Per300
1-3
单位Unit : mm
X轴方向运动与床台基准沟侧面之平行度
Parallelism between movement in X axis direction and Side surface of table reference slot
每300mm的量测距离下
许可差为
a measuring
length of 300
1-2
固定端300处
At 300 position
主轴轴线与Z轴轴线运动间的平行度
Parallelism between the spindle axis and
the Z-axis motion
a:300
b:300
主轴在Z轴方向之移(松)
动量
Movement of main spindle in Z axis direction
主轴端面之偏摆
Run out of main spindle outer surface
1-4
主轴外面之偏摆
Run out of main spindle outer surface
床台X轴方向运动之直线度
Straightness of table movement in the X axis.
a fixed indicator to the straight edge as the figure shown.
Repeatability of tool angle after tool change.
车刀角度停止後重复定位精度
Repeatability of tool angle after tool stop.
车刀加工後定位精度
Repeatability of tool angle after machining part
Straightness of table movement in the Y axis
1-5
a fixed indicator to the straight edge as the figure shown.
to get reading at both ends of the straight edge.
项
次
NO
检查项目
Inspection item
测试方法图
Measuring method diagram
许可差
Permissible deviation
实际
测量值
Measured value
主轴孔内面之偏摆
Run out of spindle taper hole
固定端
At spindle side end of test bar