Router 0
Router>
Router>
Router>
Router>en
Router#confi
Router#configure
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z. Router(config)#int
Router(config)#interface f
Router(config)#interface fastEthernet 0/0
Router(config-if)#ip add
Router(config-if)#ip address 192.168.1.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#
Router(config-if)#
Router(config-if)#
Router(config-if)#exit
Router(config)#int
Router(config)#interface s
Router(config)#interface serial 0/0/0
Router(config-if)#cl
Router(config-if)#clock ra
Router(config-if)#clock rate 64000
Router(config-if)#ip add
Router(config-if)#ip address 192.168.2.1
% Incomplete command.
Router(config-if)#ip address 192.168.2.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down
Router(config-if)#exit
Router(config)#ip route
Router(config)#ip route 0.0.0.0 0.0.0.0 192.168.2.2
Router(config)#
Router 1
Router>
Router>
Router>en
Router#conf
Router#configure
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int
Router(config)#interface s
Router(config)#interface serial 0/0/0
Router(config-if)#ip add
Router(config-if)#ip address 192.168.2.2 255.255.255.0
Router(config-if)#no shut
Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
Router(config-if)#exit
Router(config)#int
Router(config)#interface s
Router(config)#interface serial 0/0/1
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up
Router(config-if)#cl
Router(config-if)#clock ra
Router(config-if)#clock rate 64000
Router(config-if)#ip add
Router(config-if)#ip address 192.168.3.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to down Router(config-if)#
Router(config-if)#exit
Router(config)#ip rout
Router(config)#ip route 192.168.1.0 255.255.255.0 192.168.2.1 Router(config)#ip rou
Router(config)#ip route 192.168.4.0 255.255.255.0 192.168.3.2 Router(config)#
Router 2
Router>
Router>
Router>en
Router#conf
Router#configure
Configuring from terminal, memory, or network [terminal]? Enter configuration commands, one per line. End with CNTL/Z. Router(config)#int
Router(config)#interface s
Router(config)#interface serial 0/0/0
Router(config-if)#ip add
Router(config-if)#ip address 192.168.3.2 255.255.255.0
Router(config-if)#no shut
Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up
Router(config-if)#exit
Router(config)#int
Router(config)#interface f
Router(config)#interface fastEthernet 0/0
Router(config-if)#ip add
Router(config-if)#ip address 192.168.4.1 255.255.255.0
Router(config-if)#exit
Router(config)#ip rout
Router(config)#ip route 0.0.0.0 0.0.0.0 192.168.3.1
Router(config)#。