RA(config)#ints1/2
RA(config-if)#ipadd 172.16.10.1 255.255.255.0
RA(config-if)#clock rate 64000
RA(config-if)#clock rate setting is only valid for DCE ports.
serial 1/2 is UP , line protocol is UP
Hardware is PQ2 SCC HDLC CONTROLLER serial
Interface address is: 172.16.10.1/24
MTU 1500 bytes, BW 2000Kbit
Encapsulation protocol is HDLC,loopbacknot set
450 packets output, 9900 bytes, 0underruns
0 output errors, 0 collisions, 4 interface resets
1 carrier transitions
V35 DTE cable
DCD=up DSR=up DTR=up RTS=up CTS=up
RA(config-if)#exit
RA(config)#intf1/0
RA(config-if)#ipadd 192.168.10.1 255.255.255.0
RA(config-if)#end
RA#
Configured from console by console
RA#showints 1/2
450 packets input, 9900 bytes, 0 no buffer
Received 450 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 abort
450 packets output, 9900 bytes, 0underruns
RA#showints 1/2
serial 1/2 is UP , line protocol is UP
Hardware is PQ2 SCC HDLC CONTROLLER serial
Interface address is: 172.16.10.1/24
MTU 1500 bytes, BW 2000Kbit
!
interface serial 1/2
ipaddress 172.16.10.1 255.255.255.0
!
--More-
Show running-config
2.交换机（路由器）B
Show running-config
张碧波：
ra(config)#hostname RA
RA(config)#ints1/2
Encapsulation protocol is HDLC,loopbacknot set
Keepaliveinterval is 10 sec , set
Carrier delay is 2 sec
RXloadis 1 ,Txloadis 1
Queueingstrategy: WFQ
5 minutes input rate 17 bits/sec, 0 packets/sec
RA(config-if)#ipadd 172.16.10.1 255.255.255.0
RA(config-if)#clock rate 64000
RA(config-if)#clock rate setting is only valid for DCE ports.
no shutdown
RA(config-if)#no shutdown
5 minutes output rate 17 bits/sec, 0 packets/sec
450 packets input, 9900 bytes, 0 no buffer
Received 450 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 abort
RA#showrunn
Building configuration...
Current configuration : 619 bytes
!
version 8.4 (building 15)
hostname RA
!
!
!
!
!
!
!
!
!
no service password-encryption
!
!
!
!
!
no shutdown
RA(config-if)#no shutdown
RA(config-if)#exit
RA(config)#intf1/0
RA(config-if)#ipadd 192.168.10.1 255.255.255.0
RA(config-if)#end
RA#
Configured from console by console
Keepaliveinterval is 10 sec , set
Carrier delay is 2 sec
RXloadis 1 ,Txloadis 1
Queueingstrategy: WFQ
5 minutes input rate 17 bits/sec, 0 packets/sec
5 minutes output rate 17 bits/sec, 0 packets/sec
《路由器及其配置》实验结果文件
实验名称
实验小组
第7组
组长
张碧波
成员名单
张碧波许金皓李松艳刘晓萍孙萌萌朱晓王玉勤夏战辉
成员分工
路由器A夏战辉张碧波许金皓
路由器B：李松艳刘晓萍孙萌萌朱晓王玉勤
完成情况
未完成原因
实验成绩
附：实验配置命令清单及显示结果
1．交换机（路由器）A
夏战辉：
ra(config)#hostname RA
0 output errors, 0 collisions, 4 interface resets
1 carrier transitions
V35 DTE cable
DCD=up DSR=up DTR=up RTS=up CTS=up
RA#showrunn
Building configuration...