, , , and –.n )/100 ´ 1 h for HEV applI max and power can be calcuRegener I t for BEV applicationAand Figure 3b.at.If the voltage reaches the N is a value (1/h)NOTE The value of N = 3/h is an specifications of commercialized BEVs.ed derived from equation (12) is larger than the maximum power of cell specified by ttest power shall be defined as 80 % of the maximum power at room temperature and aby the manufacturer. Power value actually used shall be reported.Figure 4 – Dynaprofile A for BEV cycle test Step 4 - Discharge the cell following the dynamic dis(hill climbing profile) specified in Table 4 and Figure 5 for one time. The test pcalculated using equation (12).If the voltage reaches the lower limit specified byduring step 4, the test shall be discontinued notwithstanding the stipulation in 7cell performance shall be measured at this point as specified in 7.7.1.2 c).If thefrequently reaches the lower limit voltage during charge/discharge step 16, the diduration can be changed appropriately. The actual test values shall be reported acDynamic discharge profile B for BEV cycle testFigure 5 – Dynamic discharge prcycle test Step 5 - Discharge the cell following the dynamic discharge profile A spand Figure 4 until the overall discharge capacity including step 3 and step 4 reac% of initial C D at .If the temperature of cell reaches the upper limit specified bduring step 5, the duration of charge/discharge step Table 3 can be extended to aThe actual duration time shall be reported.If the voltage reaches the lower limitmanufacturer during step 5, the test shall be discontinued notwithstanding the stid), and the cell performance shall be measured at this point as specified in 7.7.1measurement of performanceAfter every completion of the repetition from step 1 todays, the performanceof cell shall be measured as specified in 7.7.1.1. The accumu1 to step 7.7.1.2 b) shall also be reported. The dynamic discharge capacity shall2 K only.d) Termination of testThe cycle life test shall be terminated when eitherconditions is satisfied. Otherwise back to 7.7.1.2 a) and repeat the test. Conditisequence from 7.7.1.2 a) to 7.7.) is repeated 6 times.Condition B – When any of tmeasured in 7.7.1.2 c) is decreased to less than 80 % of the initial value.Condititemperature of cell reaches the upper limit agreed between the manufacturer and ththe test.The number of implemented times of each profile and cycle during the test teststipulation in 7.7.1.2 d), and the cell performance shall be measured at this poin 7.7.1.2 c).If the temperature of cell reaches the upper limit specified by the man step 3, the duration of charge/discharge step Table 3 can be extended to an appro actual duration time shall be reported.In this profile, the test power shall be ca equation (12)P max = N W ed (12)where P max is the test power (W);N is a value (1/h)NOTE The value of N = 3/h is an ArrayFigure 4 – DynaQ c usingI n is dI and the disch W= (14)wherη c is coulomb efficiencyηThis paragraph iAnnex A.I tAof cell.1 Power P d=U d×I dmaxI t A for BEV application and 1capacity Caxan the maximum power of cell specified by the manufacturer, the the maximum power at room temperature and at 20 % SOC specified ly used shall be reported.Figure 4 – Dynamic discharge ischarge the cell following the dynamic discharge profile Bble 4 and Figure 5 for one time. The test power shall beoltage reaches the lower limit specified by the manufacturer tinued notwithstanding the stipulation in 7.7.1.2 d), and the his point as specified in 7.7.1.2 c).If the battery voltageage during charge/discharge step 16, the discharge power and The actual test values shall be reported accordingly.Table 4 –cle testFigure 5 – Dynamic discharge profile B for BEV ollowing the dynamic discharge profile A specified in Table 3 e capacity including step 3 and step 4 reaches equivalent to 80 of cell reaches the upper limit specified by the manufacturer ischarge step Table 3 can be extended to an appropriate value. ted.If the voltage reaches the lower limit specified by theall be discontinued notwithstanding the stipulation in 7.7.1.2 easured at this point as specified in 7.7.1.2 c).c) Periodical ompletion of the repetition from step 1 to step 5 for 28 test easured as specified in 7.7.1.1. The accumulated time from step orted. The dynamic discharge capacity shall be measured at ±e life test shall be terminated when either of the followingto 7.7.1.2 a) and repeat the test. Condition A – The test peated 6 times.Condition B – When any of the performanceless than 80 % of the initial value.Condition C – Theimit agreed between the manufacturer and the customer durings of each profile and cycle during the test shall be reported.performance shall be measured at this point as specified ineaches the upper limit specified by the manufacturer duringe step Table 3 can be extended to an appropriate value. TheIn this profile, the test power shall be calculated usingax is the test power (W);N is a value (1/h) of vehicle required7.7.2.1 Measurement of initial ponds (sty Q dgy (Wh);I n =100d。