ID
Description
ID
Description
D1 Red LED, Error status RESET Reset Button
D2 Yellow LED, Connection J1 Mini-USB Interface
D3 Blue LED, Busy status J2 10pin 2.54mm ARM JTAG/SW Interface
Delete the firmware.bin file in removable disk.
3. Copy the downloaded firmware: ColinkEx_firmware_v0.4.bin into the removable disk.
4. Disconnect JP1, power on again, then CoLinkEx will work normally.
JP1 Update Pin
J3 10pin 2mm ARM JTAG/SW Interface
JP2 Power Supply Pin
J4 20pin 2.54mm ARM JTAG/SW Interface
2.2 Jumpers settings
ID Name JP1 UPDATE JP2 Power
COLINK-硬件调试适配器, 用于 ARM Cortex M3,M0
产品概述
COLINKEX 是一个硬件调试适配器, 支持 SW 调试和支持 ARM Cortex M 设备. 它支持在 CooCox 软件和 Keil Real View MDK 中进行调试. CoLinkEx 通过迷你 USB AB 接口同电脑进行通讯并获 取电源, 它提供 4 个 LED 灯, 显示 CoLinkEx 的功率状态, 错误, 连接, 以及忙碌状态. 使用 CoLinkEx 时, 电脑需要 2.0GHz CPU, 512M 内存, 一个 USB 接口, 使用 COM1 的串行线路接口, Windows XP/Windows Vista/Win 7 操作系统和 CoIDE, MDK, IAR(含 CoMDKPlugin, CoIARPlugin) 软件.
1. CoLinkEx Overview
1.1 Introduction & Feature
CoLinkEx is a hardware debugging adapter which supports SW debugging and supports ARM Cortex M devices, it supports debugging in CooCox software and Keil RealView MDK.
2.3 SW/JTAG Debug Interface
CoLinkEx use ARM standard 20 pin, 2.54mm SW/JTAG Interface. Most target board support this interface. The 10pin 2.54mm/2.0mm interface is also supported. You can use the interface to debug ARM Cortex M devices. If your target doesn’t support these three interfaces, see: How to use CoLinkEx to debug other devices.
3.3 Preparation
Install CoIDE or the corresponding Plugin o Update the firmware and install the driver, Refer to: CoLinkEx Installation and Use o Jumpers’ setting: JP1, JP2 both OFF. o USB Connection: Using USB cable, one end plugged into the Mini USB port on the
4.1.2 Install the Driver of CoLinkEx
The driver can also be downloaded from /wiki/coocox/CoLinkEx/CoLinkEx-Support#Software. If you're using the Windows XP/Windows Vista/Windows 7 system, Installation file: Tools\CoLinkExUsbDriver-1.2.1.exe
3.2 Hardware Source Requirement
When you use CoLinkEx, The PC is required to use the following sources:
CPU: 2.0GHz (at least) Memory: 512M (at least) USB Interface: 1 (at least) Operation System: Windows XP/Windows Vista/Win 7 Software need: CoIDE, MDK(with CoMDKPlugin)
2.4 Mini USB Port
CoLinkEx communicate and get power from PC through this Mini USB AB interface. When you Installed JP2, CoLinkEx will give the power supply to the target board.
2.5 LED
CoLinkEx provide 4 LEDs, They show the power status, error, connection, busy status of CoLinkEx.
3. Getting Started
3.1 Version Information
Firmware: 0.4 Driver: 1.2.0 (or 1.2.1) Software: o CoIDE 1.4.0 or higher o CoFlash1.4.0 or higher o MDK 4.03(or higher) plus CoMDKPlugin1.4.0 or higher
特点: 支持 CORTEX M 设备, 支持软件与 JTAG 调试, 支持 CoFlash, CoIDE, MDK 和 IAR.
产品类型: 调试器/仿真器
硅芯系列号: LPC13xx
产品范围: 用于 ARM Cortex M3 M0 等内核芯片
内核架构: ARM
应用
嵌入式设计与开发
支持厂家
Active-Semi Atmel Cypress Toshiba ST Nuvoton NXP Holtek
1. Double Click the EXE file, enter the installation interface, click "Next".
1. Select the installation location, click "Next". 2. Click "Install".
3. Click "Finish".
CoLinkEx support is available in: Keil RealView MDK 4.03 or higher (not include 4.13a) IAR Embedded Workbench 5.xx or higher CooCox CoFlash CooCox CoIDE CoLinkEx Software: CoLinkEx Plugin for Keil RealView MDK CoLinkEx Plugin for IAR Embedded Workbench
Default Settings
Open
Open
Note
Allow user to update the firmware of CoLinkEx when this jumper is closed. Connecting VCC pin of the ARM JTAG/SW Interface to +3V3.
Features:
Supports Cortex-M devices - Supports SW debugging Supports JTAG debugging Supports CoFlash, CoIDE, MDK
2. Hardware Introduction
2.1 Over View
Downloads: /software.html Buy: /casetwo.aspx?cid=5&id=24
Colinkex(ET-COLINK-1)使用指南:
1. CoLinkEx Overview ====================== 1.1 Introduction & Feature ----------------------
支持 Cortex-M 设备 支持 SW 调试 支持 JTAG 调试 支持 Keil Real View MDK 4.03 或更高 支持 IAR 内嵌工作台 5. xx 或更高 支持 CooCox CoFlash 支持 CooCox CoIDE
产品信息
套件包含: 仅调试电路板 数据线 UART 下载器 隔离板(选配)
4.1.1 Update the Fra bibliotekirmware
If you are using CoMDKPlugin V1.4.0, CoIDE V1.4.0, or CoFlash V1.4.0 or higher version, you may need to update CoLinkEx driver and firmware before using CooCox CoLinkEx. (That operation is not needed when you bought the CoLinkEx after 2012, August) The firmware can be found in the disk: Tools\ ColinkEx_Driver\ColinkEx_firmware_v0.4.bin, you can also download it from: /wiki/coocox/CoLinkEx/CoLinkEx-Support#Software. How to update the firmware: 1. Short-circuit JP1. 2. Connect CoLinkEx to the PC. Wait for the PC enumerates the removable disk whose label is "CRP2 ENABLD" or "CRP DISABLD". If it does not, you could press the reset button (BP1) for several times or power on again.