PM RESEARCH'S 下午研究的V ertical Boiler 立式锅炉Put life into your steam engines, run them on live steam.把生活到您的蒸汽机，运行他们对生活的蒸汽。

What a sight!什么是忽视！This boiler will easily run one of our well这很容易会锅炉运行我们的一个好constructed #2, #3 or #5 steam engines for light-duty use兴建＃2 ，3号或5号蒸汽机为轻税，使用and demonstration purposes.和示范的目的。

- -The boiler kit comes with just about everything you need to build a great vertical boiler. 锅炉套件，只要一切你需要建立一个伟大的垂直锅炉。

You'll find the material nessesary to make the riveting tools except the anvil itself. 您可以找到的物质nessesary使铆工具，除砧本身。

Lets start with making the tools for installing the tubes as well as the rivets. 让开始与决策的工具，安装管道，以及为铆钉。

Then we will be set to begin on the boiler itself. 然后，我们将被设置为开始对锅炉本身。

Ther are four tools needed for setting the rivets. 有四个必要的工具，订定铆钉。

The three on the right are for the outside of the heads, while the anvil and another punch is for the inside to hold the rivet in place while swagging and peening the head over. 三个在右边，是为外面的元首，而砧和另一冲床是为内举行铆钉在的地方，而swagging和喷丸头以上。

PM gives an excellent discription of how to make the tools, harden them and also how to properly set them. 时给出了一个良好的discription如何使工具，变硬，他们也如何正确设置。

Also shown is how to make the flaring and rounding over tool for installing the firetubes. 还表明，是如何使燃烧和四舍五入，超过的工具，安装firetubes 。

Again they give a great discription of how to do this. 再次给予他们一个伟大discription如何做到这一点。

To the left is the anvil tool that is used to hold the rivets while you set them in place by peening them. 到左边是砧的工具，是用来举行铆钉，而您所设定的，他们在的地方，由喷丸他们。

Its really a simple job taking only about a minute for each one. 它真是一个简单的就业考虑，只有约一分钟，每1 。

Notice on the two tools on the right side have bands on them. 通知就这两个工具在右侧有阶，对他们的影响。

The middle one with the longer band is the deeper of the two which are hard to tell apart. 中东一与较长的波段是更深的两个，这是很难说，除了。

The one on the right has a shallow band indicating the hole in the end is shorter. 一个在右边有一个浅带，表明该洞在年底较短。

It makes it a lot easier when installing them. 它使很多时，更容易安装。

The picture on the left shows how I added three pieces of 1/4" square to my anvil to help hold it in my vise. You can see where I tacked two on the top and there is also one on the bottom. My vise was allowing it to slip down and this prevented it from moving. 图片在左边显示我如何补充，三件1 / 4 “广场，我的砧，以协助举行，它在我vise 。

你可以看到我tacked两个对顶，也有一对底部。

vise是我的允许它的支路下来，这使它无法移动。

Shown is the flaring tool used for the boiler tubes, The one on the left is used for rounding over the tubes while the right one is used to start the flare so the left one can bend them down flat. 显示是燃烧的工具，用于锅炉管，一个在左边是用于四舍五入超过管，而正确的，一个是用来启动耀斑，使左边的人可以弯下来的单位。

The thirteen boiler tubes were cut to length with my small cutoff tool. 该13锅炉管被切断，以长度与我的小截止工具。

Its great for small pieces of copper and brass. 其强大的为小件铜和黄铜。

I wouldn't want to cut much larger than these tools. 我不会要削减远远大于这些工具。

I bought it from for 20 dollars on sale. 我买它从为20美元出售。

A good deal for the money! 是一个很好的协议，为钱！The pieces were then deburred and the ends cleaned for soldering 该件当时deburred和结束清理焊接While making the tools I also made four wooden blocks to use as spacers between the top and bottom sheets. 而决策的工具，我也取得了4块木制使用作为间隔之间的顶部和底部的工作表。

This enables you to use a bolt provided to flare out the tubes 这样，您就可以使用螺栓提供耀斑列管Here we have seven tubes installed with six to go. 在这里，我们有七管安装6路要走。

Use a drop of oil on the end of the flaring tool as it makes it much easier and does a better job. 使用减少了对石油的结尾部分燃烧的工具，因为它使得它容易得多，并做得更好。

You can clean the oil off before soldering. 您可以清洁石油起飞前，焊锡。

I thoght this might be a problem but after using a good degreser and some alchol it soldered just fine. i thoght这可能是一个问题，但用后一个良好的degreser和一些酒精，它焊接刚才的罚款。

I'm getting ready to flare the tube first and then round over the end using the other side of the tool. 我准备耀斑管，然后第一轮比上年末使用对方的工具。

It only taks a few minutes to install each tube. 它只是taks了数分钟，安装每个管。

The whole job took less than an hour. 整个工作用了不到1小时。

- -Here's good picture of the boiler tube tool. 这里的好图片的锅炉管的工具。

I changed mine a little from what PM showed in his drawings. 我改变小煤矿从什么时表明，在他的图纸。

On the left side of the tool I made the part that goes in the tube with a 2 degree taper to try and expand the tubing as its flared. 在左侧的工具，我那部分有云，在管内2度锥度尝试和扩大油管作为其爆发。

You can see the backup wooden blocks in this picture. 你可以看到备份的木制座在这方面的图片。

There is also a small radius as PM shows on the drawings. 还有一个小半径作为时，表明对图纸。

This gives a nice radius when the tubes are bent over. 这使尼斯半径时，管热衷。

I didn't try to anneal the tubes as they bent just fine with no splitting at all. 我没有尝试退火管，因为他们一意孤行，只是罚款，没有分裂，在所有。