一.基本信息配置 system-view //进入系统视图 [H3C]sysname RT3 //为设备命名 [RT3]super password simple H3C //设置超级密码 [RT3]local-user admin //添加用户 [RT3-luser-admin]password simple admin //为用户设定密码 [RT3-luser-admin]service-type telnet //指定用户的类型 [RT3-luser-admin]quit //返回上一级 [RT3]user-interface vty 0 4 //进入 vty [RT3-ui-vty0-4]set authentication password simple telnet //设置远程登陆认证，密码为 telnet [RT3-ui-vty0-4]idle-timeout 5 0 //配置超时退出时间 其它略 二、链路配置及调测 interface Serial0/2/0 ip address 10.1.13.2 255.255.255.252 undo shutdown interface LoopBack0 ip address 3.3.3.3 255.255.255.255 undo shutdown
1
interface Ethernet0/1/0 ip address 10.1.3.1 255.255.255.0 undo shutdown 其它略 三、OSPF 多区域及 RIP 配置 [RT3] ospf 1 router-id 3.3.3.3 //配置 OSPF ROUTER-ID silent-interface all //配置所有端口为被动接口 undo silent-interface Serial0/2/0 //关闭此接口的被动接口 undo silent-interface Serial0/2/2 area 1 //OSPF 区域，可以写成点分十进制 0.0.0.1 network 3.3.3.3 0.0.0.0 //宣告 OSPF 的网段 network 10.1.13.0 0.0.0.3 network 10.1.3.0 0.0.0.255 [RT1] ospf 1 router-id 1.1.1.1 silent-interface all undo silent-interface Serial0/2/0 undo silent-interface Serial0/2/2 area 0 network 10.0.15.0 0.0.0.3 network 1.1.1.1 0.0.0.0 area 1 network 10.1.13.0 0.0.0.3 network 10.1.1.0 0.0.0.255 [RT5] ospf 1 router-id 5.5.5.5 silent-interface all undo silent-interface Serial0/2/0 undo silent-interface Serial0/2/2 area 0 network 10.0.15.0 0.0.0.3 network 5.5.5.5 0.0.0.0 network 10.0.5.0 0.0.0.255 network 10.0.56.0 0.0.0.3 [RT6] ospf 1 router-id 6.6.6.6 silent-interface all undo silent-interface Serial0/2/0 undo silent-interface Serial0/2/2 area 0 network 10.0.56.0 0.0.0.3 network 6.6.6.6 0.0.0.0 area 2
2
network 10.2.6.0 0.0.0.255 network 10.2.26.0 0.0.0.3 [RT2] ospf 1 router-id 2.2.2.2 silent-interface all undo silent-interface Serial0/2/2 area 2 network 10.2.26.0 0.0.0.3 netwoork 10.2.2.1 0.0.0.255 rip //启动 RIP undo summary //关闭自动汇总 version 2 //RIPV2 network 172.16.0.0 //宣告 RIP 的网段 silent-interface all //配置所有接口为被动接口 undo silent-interface Serial0/2/3 //将接口不设为被动接口 [RT4] rip undo summary version 2 network 172.16.0.0 network 4.0.0.0 silent-interface all undo silent-interface Serial0/2/1 四、OSPF 重分布外部路由及下发缺省路由 [RT5] ospf 1 area 0 import-route direct cost 1000 type 2 //重分布直连路由 default-route-advertise always //下发缺省路由 default cost 2000 //指定缺省路由的 COST 为 2000 default type 1 //指定下发的缺省路由为类型 1 [RT2] ospf 1 area 2 import-route rip 1 cost 1000 //重分布 RIP 到 OSPF rip import-route ospf 1 cost 5 //重分布 OSPF 到 RIP 五、OSPF 特殊区域配置及路由汇总 [RT3]ospf 1 area 1 stub //配置为 STUB 区域 [RT1]ospf 1 area 1