深圳市宝安区西乡镇勒竹角村天富安工业园3栋5楼东承认书SpecificationProduct/产品 : White LAMP LED Part Number/型号 : YL-P0513W-AB-14 Customer/客户 : -------------- Issue Date /发行日期 :2011-08-08Customer Confirmation客户确认MAKER 制定Prepared 制作 Checked 审核Approved 核准刘刚版本A0深圳市宝安区西乡镇勒竹角村天富安工业园3栋5楼东◆Features/产品特点․High reliability (可靠性好)․High Luminous Intensity （亮度高）․Peak wavelength λp=660nm （峰值波长λp=660nm ） ․surface light emitting （表面发光结构） ․Low forward voltage （低电压） ․Pb Free（使用自由、方便）․This product itself will remain within RoHS compliant version. （产品本身符合RoHS 认证标准）◆Applications/应用․（在日照量少或日照时间短的时候作为植物光合作用的补充照明） ․（植物工厂的主要照明并为植物提供周期、光形态建成的诱导照明） ․（广泛应用于水溶液培养，园林，播种，育种，幼苗，农场，花卉等栽培）◆Device Selection GuideLED Part No.Chip Lens ColorMaterialAlGaInPWater clear深圳市宝安区西乡镇勒竹角村天富安工业园3栋5楼东◆Absolute maximum ratings/最大绝对额定值◆ Shape Specification /外观要求Parameter 参数Symbol 符号 Value 数值 Unit 单位 Continuous Forward Current持续工作电流 If60 mA Reverse Voltage 反向电压V R 5 V Operating Temperature 工作温度T opr -25～+85 ℃ Storage Temperature 储存温度T stg -35～+85 ℃ Soldering temperature 焊接温度T sol 260±5℃（for4sec ）℃ Power Dissipation 功率消耗P d150 mW Pulse Current 脉冲电流I FP 200mANo. 序号 ITEM 项目 SPEC OR DESCRIPTION 规格要求描述1Lens 胶体◆ No change color/不可有胶体变色 ◆ No Disrepair/不可有破损◆ Scratch/划伤（length ≤2.0mm,Width≤0.25mm） ◆ macula/黑点、异物（≤0.25mm and ≤2EA in Encapsulation reverse） ◆ bubble/气泡（≤0.3mm and ≤2EA Encapsulation reverse） 2 PIN PIN 脚◆No oxidation/不可有氧化 3Configuration 结构 ◆No PIN loosen/PIN 脚不可松动4 surface preparation表面处理 ◆ Cut needn’t electroplate /切口处无需作电镀5Lens color 胶体颜色◆ Water Clear 水透明深圳市宝安区西乡镇勒竹角村天富安工业园3栋5楼东◆ Dimensional drawing/尺寸图2112◆ Opto-Electronical Characteristics /光电参数特性 (Ta=25℃)◆ Opto-Electronical Rank /光电分级规格Condition ：I F =20mA Unit ：mcd参数 Parameter 符号 Symbol测试条件 Condition 最小 Min. 平均 Typ. 最大 Max. 单位 Units 发光强度（Luminous Intensity ）Ee I F =20mA -- 180 -- mcd 峰值波长（Peak Wavelength ）λp I F =20mA -- 660 -- nm 波宽（Spectral Bandwidth ）Δλ I F =20mA -- 45 -- nm 正向电压（Forward Voltage ）V F I F =20mA -- 2.1 2.5 V 反向电流 （Reverse Current ）I RV R =5V -- -- 10 μA 角度（View Angle ）2θ1/2 I F =20mA--120--DegBin Number M N P Q R 最小（Min ）180 230 280 330 380 最大（Max ）250300350400450◆Typical Electro-Optical Characteristics Curves/光电特性曲线图深圳市宝安区西乡镇勒竹角村天富安工业园3栋5楼东◆ Lighting Angle /发光角度◆ Reliability Test Items/可靠度测试项目No.Item Condition Time/Cycle Number of Damaged 测度项目测试条件 测试时间或周期不良数/测试数1Soldering Heat Test260±5 o C 10 sec0/60焊接试验 2 Thermal Shock0 o C (15sec) ~ 100 oC(15sec)20 cycle 0/60热冲击 3 High Temp. Storage100 o C 1000Hrs 0/60高温储存 4 Low Temp. Storage-40 o C 1000Hrs 0/60低温储存 5 Temperature Cycle Test-40 o C ~ 80 o C100 Cycles, 200 Hrs 0/60高低温循环6High Temp. High HumidityTest60 o C, 90 % RH1000 Hrs 0/60高温高湿 7 Operation Life Test 1Room Temp., 20mA 1000 Hrs 0/60常温老化 8 Operation Life Test 2Room Temp., 30mA500 Hrs 0/60常温老化9 High Temp. Operation Life Test85 o C ,10mA 1000 Hrs 0/60高温老化10 Low Temp. Operation Life Test-30 o C , 20mA1000 Hrs 0/60低温老化深圳市宝安区西乡镇勒竹角村天富安工业园3栋5楼东◆Judgment Criteria/判定标准：ItemSymbolTest ConditionsJudgment Criteria项目Forward VoltageVf I F = 20 mA Δ% < 10 % 正向电压Leakage CurrentIr Vr = 5V <10 uA 反向漏电流Luminous IntensityIv I F = 20 mA Δ%< 10% 发光强度Peak WavelengthlmI F = 20 mAΔ%< 5%峰值波长◆ Reflow/回流焊接Lead Solder/有铅焊接Lead-Free Solder/无铅焊接深圳市宝安区西乡镇勒竹角村天富安工业园3栋5楼东◆ Packaging Specifications/包装规格箱号标签3防静电袋：140*180外中箱尺寸：340*323*328外大箱尺寸：495*358*357标签2标签3内小箱尺寸：220*160*150内中箱尺寸：340*235*165标签箱号标签一(80*10mm)ROHSWavelengthQ.TY Luminous Inte nsityVoltageLot NOClient code 产品型号Patr No.标签三.ROHS条码区域QC数量Q.TY客户料号Client code 外形描述Appearance 产品型号Patr Num 标签二(52*70mm )ROHS条码区域产品型号Patr Num数 量Q.TYBIN 号CIE Range发光角度Light angle 电 压Voltage发光强度Luminous Intensity 批号Lot NO外形描述Appearance 产品型号Patr No.客户料号Client code◆Caution/注意事项1、Before opening the package： the LED should be kept at 30o C or less and 90 % RH or less.打开包装前请在温度30 o C湿度90%的环境以下储存。

2、After openning the package ：the LED should be kept at 30o C or less and 30%RH or less.The LED should be soldered within 168h( 7days)after opening the package. If unused LEDs remain，they should be stored in moisture proof package，such as sealed containers with packages of moisture absorbent material(silica gel). It is also recommended to return the LEDs to the original moisture proof bag and to seal the moisture bag again.打开包装后，LED请在温度30 o C湿度60%的环境以下储存，并应在168小时内完成焊接。

如果包装打开后，未用完的LED应放置在防潮包装中，比如含有防潮剂（硅胶）的袋子中。

建议将此LED返回到原始包装带中并将其封口。

3、After openning the package ,If the humidity indicator’s color change from blue to pink at 30% or more, and if the LEDs have exceed the storage time, bake treatment should be performed using the following conditions.baking treatment :more than 24 hours at 60±5 o C。