MOTO A925尾插通用接口定义：1-地, 6-供电, 4-D+, 5-D－V3尾插通用机型接口定义：1―地、5-供电、3-D+、4-D－）V680,V730: TX-3, RX-4, 地-5V998定义：9-GND, 11-UPLINK, 12-DOWNLINK, 13-DSCEN(5V), 14-EXT B+MOTO A768: SC29301,320W18,62147CV; 电源5188450 43A56; PXA262B1, HYE25L25616,040KAD1J, MD4832-d512; 功放k407e051b; BLUETOOTHSS E820: 6359EL1/3C5, KBB06B400M, C60501E, MV317SAQ, Y765, UAA3536, 3146, USB接口BC03P416SS d508: 5212EL10443e, KAP17WG00A, MV319DNQ, CF50603, Y765, RF3587G MP2590, BGY284Ed500 接口: 1-14-Batt, 2-D-, 3-Usb+, 4-D+, 5-Tx, 6-Rx, 8-11-GNDSS E808: 6359EL1/3, KBB06B400M, 照相MV317AQ, 电源C50601E, RF3146, PLL UAA3536, Y765, 3699, 3664, BC03SS P100: TR09WQTED28, LRS1828B, CSP1093CR1, SSH275, PSC2006, Si4205, Y762, LC9970, RF3133SS P518: CX80502, 3350WWZ, CX74063, CX20524, 功放CKY7732, CLC346, 和旋SEMAF三星S108：1-3-18-VDD, 20-22-GND, 19-RX, 23-TX, 13-RI 14-CD未试E700、d500（PCB093LBE）: 1-2-充, 3-扬声器, 4-RX2, 5-外电, 6-8-11-GND, 7-PWON, 9-TX2, 10-MIC, 12-充控, 13-JIG, 15-RTS1, 16-TX117-RX1, 18外电E708（PCB133LBEC）的数据线ＤＩＹＤ５００的数据线把原来的２，３线换到５，６脚就可以了．大家试一下（２－５．３－６）．可以刷机D518：10-GND, 12-TX, 13-RX索爱USB: T68、T238、T290C、J300C、T628、K500C、K506C、K508C、K700I、K700C、K300C、S700I、S700C、P800、P802、P900、P908、P910I、P910C等索爱DCU-11: A2218/A26XX/T20/T29/T60/T61/T62/R300/R380/R520/R600/T200/R320/T39/T100/T681/Z200 /Z208/T26T266S/T230/T300/T306/T310/T312/T316/T630/T620/T618/T610/P800/P802/Z600/Z608/P900/902/K700/K500/K506/K508/T290S/P910/z1010/J300索爱DCU-60: D750I K310 K510 K610 K750I K750C K758 M600 M608 P990 W300 W550 W600W700 W710 W800 W810 W900I W950 W958 Z520 Z525A Z530 Z550 Z710LG G282: AD6527BAB, 4455LZB, AD6535ABC, NEC5250T, CL761ST, NWV50, Si4205, 77325-12LG G232: AD6527BAB, AD6537, 4050L0Z, Si4205, 77325: 12-19-GND, 1-JTAGEN, 2-RST, 18-TX, 24-RX天龙T99/美晨T788首信c6268：13-TX, 16-RX, 20-VDD, 22-GND天龙T88、高科S238：8-RX,17-TX, 18-19-GND, 21-22-23-Vddsenson s308: 6525ACA; LRS1826A, 6521ACA, 155141, 3408, Y762C松下G70: 6525ACA; 5682CDSB; 6537; 762C; CX74063; CX77314-14松下X66: PMB7850E 3.1F, NEC MC26426312, PMB6810, PMB6256, RF3140, Y759三菱MT550: OM6357EL, PL129J80, 50601ET, N56964BY和旋,uaa3536,rf3133NEC N150: MT6218, PL064, MT6305, W99685, K9F5608U0, MT6219, RF3146,N6201: 4-5-充电, 12-23-Gnd, 21-22-24-BattTCL GM750: 6525, JL127, 6535, 2870A, SI4205,TCL718: 4-7-13-18-GND, 1-2-充电, 13-RX, 14-TXTCL E757 PDA K9F2808U0CTCL神典c767: 小板 vp40586A, 1602c3t, 电源Wap3A2, Si4200, Si4134, 0324CCEA, 功放CX73115-14；大板龙珠SZ328AVH， EPSON D1371401B1，DISKonCHIPMD3831D32V3，HYB39L128，CC0881，Y762TCL u2: 电源3014, AMD323GT,TCL3188的：1-12-GND（12-BOOT接地才联机）， 5-RX, 8-CTS, 10-TX, 11-RTS-13、17-VDDTCL u2 u3：2-GND, 9-RX, 10-TX, 12-VDDTCL2188：(已试)1-GND, 5-RX, 6-TX, 18-VDD测TX电压太低，在TX与VDD间加一个10K电阻就OK了TCLc328: 6-D+, 7-D-, 8-VCC, 17- GND; = TCL 628.D208.D866TCL MOBO828: 1-2-充, 3-4-17-18-地,长虹M818带MP3照像数据线用智能王的TCL700 MT20号数据线就可以写读软件或解锁6218456首爱长虹M638,M808,M898: 7-9-18-Gnd, 16-Batt, 1-2-充, 10-U+, 3-D-, 4-D+; 13-RX, 14-TX; ok海尔3000: 1-B+, 13-Batt, 2-14-地, 15-16-充, 9-TX,16-RX海尔彩智星3000：(wlx已试)2-GND, 6-TX, 7-RX, TX加一个10K电阻到VDD海尔天智星3000c: om6357el, m36w0r6030t0, pcf50601, BC03p531,2870A, IF uaa3536, 08123b3000: om6357el, 2020w0, 50601tet, bc03p415, uaa3536,2870a, 08123b, adg789海尔运天星2000: A6cpu, k5a3240y,3012, rf2253,trf6053, 08109b野马E708：3-4-GND, 14-RX, 15-TX, 22-23-24-VDD野马709: 6525, 2240WWZDQ, 6537, Y762, Si4205, RF3133G811: 80503-37, 1393A, 20460-32, 20505, CX74017, Y762, 功放16P SAMSING E518: 6357,50601, 2030W0ZT, 3536, RF3133, L2871和弦:没装屏或排线不行会不开机，电流像软件问题！三新e808+: 1-2-GND, 7-RXK, 9-TX三新SAMSING M1: 1-GND, 5-D-, 6-D+, 7-USB+, 8-充电sigmatel: PL064, Y762, D751749, 3025, TRF6151, AWT6108, 密913822 重复次数10 第一地址007095F6 最后地址007E9C461-2-batt, 7-15-16-18-gnd, 4-5-6-充电, 9-RX, 14-TXsigmatel 688: 1-2-3-Gnd, 4-5-6-充电, 7-8-9-Batt, 23-24VK700sky平台:17-18-地, 1-2-3-10-b+, 7-RX, 8-TX, 2-3-充电，060223bymikevk100: tx-7, rx-8, vcc-1VK系列和中桥C188 C288、D1已试：1-2-10-GND, 5-7-RX, 8-TX, 18-VDD 若不好联机，将10脚断开，不过联机时要按开机键。

中桥INNO-99(A龙328)的接口定义是不是依诺99啊？试:1-23-VDD, 12-TX, 13-RX, 17-GND吉事达GM888数据接口定义4-VDD 6-RX 7-8-TX 20-GND吉事达kd886 1-VDD 5-RX 6-TX 9-GND 吉事达893和８８８：６脚.和吉事达888的７脚相同，１３．１７脚相同和吉事达８８８.１１脚和１３.１７脚相同８-RX, 6-7-TX, 3-VCC, 11-GND..吉事达K899,GM128：1-2-VDD 充, 6-RX, 8-TX, 11-GND千里马339: 5-VDD, 10-14-15-GND, 12-TX, 13-RX千里马838：1-3-VDD, 4-RTS, 5-CTS, 6-RX, 7-TX, 8-11-GNDUT-618: 1-4-VDD, 3-RX, 5-TX 9-11-GNDUT115Q: UT607-101, 1602C3T, 电源T7AF2XB, 中频31168BF, 功放G7001UT117: 71AL016D02, AX545, 充电94ZF6UT718:TC35605XB, FLASH lc3mdw325a81t,SRAM m6mg3d64,ut220:T7e46F,29DL164be,62s2048,Y757b,IF 31167,PA 1051aUT620: TC35605XBM, 84VD21083E, Y759B, 中频TB31167F, 功放1051Aut628:TC35605XBM, 22184FM, Y759,V 2411, TB31167, G7001PT2689: TC35605XBM,TC58FVM5B2A(4MB),62137,803 0339充电,M33ad srb(码片?),PT3689: TC35605XBM,TC58FVM5B2A(4MB),62137,803 0414充电,y757,AAAA46码片?HW A316: TC35605fg, 29DL164bd, K6F2008暂存, TB31167中频, 41 2401功放TF518 Sram:k6f4016=EM564161JP818+ : M64174wg, vd21083, 24128, 电源8030348, Y757b, 中频M64821, 1051AV81: TC35605, 84VD22194FM, 2870, 13094006B功放V82+: 35605xbm, 40000023, ce2045, 2870, if29180, rf4026AmoiS358: 35605xbm, vd20183em, y757, tb31167, AT45db041,2135516普天PTW218G2：CPU WN1005B，29LV400BT， 24C02普天t218: 4-9-12, 11-GND, 13-RX, 14-TX天语TS8000数据线18PIN: VCC红-4, 地-8-11, 14-D-, 13-D+天语B808 18pin: 1-2-Batt, 8-11-Gnd, 13-14-USB+, 17-18-充电, 5 1V8,待完成天语B819: MT6226, TV0579002, 6305, 6129, RF3166: 1-2-Batt, 8-11-地, 13-14-USB+, 17-18-充, 9-D-, 10-D+ ; 7-RX, 12-TX CECT Q610: 11-D+, 12-D-, 5-Vcc, 6-GND = 高科S283(MP3滑盖)CECT U8800直板仿NOKIA8800定义,MTK的2-3-4-vcc, 1-11-gnd 郭靖CECT U8810带Mp3: 1-2-vcc, 8-gnd, 10-txd, 15-rxdcect Q610(MP3,滑盖照相): 地-6-16, 充电-1-2-7-8, USB+5-11, BATT-3-4,待完成cect U8800滑盖: 6219, 3040l0zb, 9f1208, 6305, 26MHz, 6m4002CECT617: 6525, PL127JB0B, 6521, 电源3522, Si4205, RF3146, Y762; 1、2-BATT，8、11-GND，cect616: ad6522naca, 41000000G, 3408, AF6521aca, PLL 6524, RF 6523, PA 08122Q610: MT6217, pl127jb, k9f1208, 6305, 629, rf3146CECT Q610: What20450,M36W0DR6040T0ZA,K9F5608Q0C, 电源WAP3A34FU,VC0938, EPSON137162, 全射频集成大块CECT Q380: MT6217AT, PL129JB0, NAND256W3A2A, MT630BN, MT6129N, RF3146, PAP1302B功放CECT M62: 1-2-充电, 14-15-BATT, 9-10-GNDTY282:Ad6522,22181,6521aca,6523,Y759,adp3408,6524TY299: 6525ACA, VD23280FA, 6521, ADP3522A, Y762C, HD155155, RF CL70351, ZMM7V X3CECT-T590超薄直板带卡小8针下载（091线）: D+3, D-4, Vusb-2, GND-8 解忧派CECT T590（MP3照相）:CPUMT6218BT，71PL064J，K9F5608U，电源MT6305N ，CECT T590一样 T606CECT 616M、FG525（MP3）、T590：8-11-GND 13-RX, 14-TX 大部分MP3机子也能用,solo S998也能用cectV6 o91-8-sedx689-mt平台下载线: 1-vcc, 6-tx, 7-rx, 8-gnd,Q658: 1-2-BATT, 3-14-GND, TX:(6,17,8,9,11), RX-18Q638: 1-2-充, 3-13-B+, 7-18-B-, 15-RX, 10-TX; 或RX-14, TX-13CECTi361: 6218,PL064,6305,6129,3146,9K1208,MB2168: 1-2-池, 8-11-地,17-18-充,13-14-U+,9-D-,10-D+,7-RX,12-TX;用CECT Q380线金立AD芯片的：GN108、GN325、GN350(B/C)、GN635.GN638、GN668、GN768、K8、N3、X5MT 芯片的：GN326、GN360、GN518、GN528、GN538(B)、GN728、N6、S90展讯芯片的：GN558、GN658GN516: 6850,5A3240yct, 6810, 6253v, RF3140金立303、506、桑达G618、619、838：9-rx, 10-tx, 13-gND金立250试GN350,三正E888：8-11-GND, 9-D-, 10-D+, 13-RX, 14-TX, 17-18-VDD, 2-3-5-6-USB+GN635: 6525, DL128, CLC346, 6521, 3522, Si4205: 1-2-B+, 8-11-B-, 17-18-充, 5-TX1, 6-RX1, 15-RX2, 16-TX2步步高k098: 1-2-电, 5-6-gnd, 15-batt天时达绝大部分MTK（18针）是: 1-2-17-18-VDD, 5-D+, 6-D-, 11-12-13-14-地天时达T617的MP3线用T26A的,天时达A316：11-RX 12-TX 13-14-GND天时达A607、A318等：7 RX, 9 TX, 8-11-18-GND适用于大部分MP3、MP4手机，以及采用MT6205的机子：托普天星V60B、天时达T-6、T6B、T636、T636+、三新508+、康佳C926，还有多台CECT贴牌机（MP3、MP4都有），平台与波导M09同。