当前位置:文档之家› COMPASS单词翻译及使用说明

COMPASS单词翻译及使用说明

COMPASS单词翻译及使用说明一、一、封面:File 文件 1)、Status 基本情况 2)、References 参数Edit 编辑 Company 公司 NS/EW:Site 坐标:区块View 视图 Field 油田 North:Grid 北:地理坐标Planning 设计 Site 区块 TVD:Datum 垂深:基准点Survey 测量数据与计算 Well 井号 Mean Sea Level 海平面Anticollision 防碰 Wellpath 轨迹类型名Utilities 有效设置 Datum 基准点(面 )Window 窗口Help 帮助二、文件:Open 打开 Graph Export: DXF FileSave 保存 (图表输出) Windos metafile 源文件Save As 。

保存New Company 新公司 Data Source 数据来源New Field 新油田 Print 打印New Site 新区块 Print Preview 打印预览New Well 新井号 Exit 退出New Wellpath 新轨迹Delete Company 删除公司Delete Field 删除油田Delete Site 删除区块Delete Well 删除井号Delete Wellpath 删除轨迹Import : Transfer File 传输文件输入 DOS Compass :dos 指针DOS Wellplan: dos 设计DFW Surveys 测量数据库Wellbore planner 设计者Export: Field 油田输出 Site 区块Well 井号Direct to wellplan 直接到设计To a wellplan file 到一个设计文件Wellbore planer 设计者三、E dit 编辑Company setup 设置公司 Survey Tools 测量工具Wellpath Types 轨迹类型Setup 栏: division 专业公司或部门 group 班组Anticollision preferences防碰参数设定error system 系统误差模型 systematic ellipse 误差椭圆 scan method 扫描方法 closest approach 3d 最近距离 error surface 表面误差 elliptical conic 椭圆锥体separation factor warning Levels 防碰警告距离survey calculation method 实测计算方法Radius of curvature 曲率半径法v.section origin 垂直剖面原点 slot 槽口(井口)co-ordinate origin 坐标中心 site 区块中心walk/turn rate 变化率 md 斜深Field 油田Site Setup 设置区块 Templates 槽口模板Targets 靶点Datum 基准点Well 井号Wellpath : setup 设置Casings 套管Formations 地层 ( Lithology 岩性)Annotation 注释Targets 靶点Survey history 测量纪录Setup 设置栏 : Rig 钻机号Parent wellpath 主井Sidetrack MD 侧钻点Vertical section origin 垂深起点Path type 井别四、View 视图Section view 垂直剖面图 common offset wells 邻井, 对比井Plan view 水平投影图 tool bar 工具栏3D view 三维图 status bar 状态栏Slot template view 槽口摸板图Definitive path 实钻轨迹Legend 图例Wall plot composer 挂图制作五、 Planning设计Open plan 打开设计New plan 新设计Delete plan 删除设计Additional plan 附加设计Export 输出Reports 报表新设计栏(New plan):plan setup – create new plan 设计设置—创建新设计plan 设计名称 MD 斜深Description 设计描述 LNC 井斜Version 版本号 AZ 方位Date 设计日期 TVD 垂深Locked 设定锁 N/S 南北坐标Principal plan 主设计 E/W 东西坐标Star point 起始点 user 用户自定义From wellhead 从井口作起始点 Depth 深度From tie-point 从某一点开始Planned survey tool history 设计测量工具纪录Select a planning option 选择一个设计选项(一)、2DJ形(直增稳)设计:Length of 1st hold 造斜点Build rate 造斜率Max Angle hold 最大井斜角Length of 2nd hold 稳斜段长Target 靶点选择Calculate 计算Ok 确认Cancel 取消(二)、二维((直-增-稳-降(增)-稳))设计Plan a 2D s well 设计一个二维S形井眼1st hold length 造斜点1st Build Rate 第一造斜率Max Angle hold 最大稳斜角2nd hold length 第二稳斜段长2nd Build Rate 第二造斜率final Inclination 最终井斜角final hold 最终稳斜段长Select the two unknowns to be calculated using the check boxes 用检查框选择两个未知参数计算出来.(三)、三维分段设计(井斜、方位的变化率)Add a build /turn section 添加一个井斜/方位变化的剖面Select the build /turn section type 选择井斜/方位变化的剖面类型1、点击MD,输入井斜/方位变化率及斜深.2、点击TVD, 输入井斜/方位变化率及垂深(火靶点)后计算,OK确认.3、点击LNC ,输入井斜/方位变化率及所需井斜值.4、点击AZ, 输入井斜/方位.(四)、三维分段设计(狗腿/工具面的变化),省落(五)、三维S形设计Add a 3D curve-hold-curve section 添加一个三维(弯曲-平稳-弯)S 形剖面Select the method for calculating the Dogleg-Hold-Dogleg solution 选择计算S形的方法,Tangent length 切线长Lined up on tangent 轨迹到靶点Final-Lnc final-Az 终点井斜、方位,Proj back 返回设计点(计算、预测)Proj back from a target 从靶点返回计算点Pick target 挑选靶点Calculated point 计算点Build rate 造斜率Inclination at target靶点井斜角Azimuth at target 靶点方位角Course length 段长(六)、稳斜设计Add a hold section 添加一个稳斜剖面Enter the hold section length either by MD or TVD 输入稳斜段斜深或垂深Hold to TVD or MD 稳斜到斜深或垂深(七)、多靶点三维剖面设计Thread a section of targets 多靶点三维剖面Select the targets to be threaded 选择靶点到三维设计Add to list 添加到列表Remove from list 从列表中移出Dogleg to Apply 狗腿使用与….Sort by 选择靶点排列顺序Displacement 按位移排序Descending TVD 按垂深排序Ascending TVD 按垂深上升排序Method 设计方法:1、curve only 设计方法为:各靶点间的造斜率为单一曲率.2、Curve hold 设计方法为:各靶点间分两段增(降)、稳.3、Optimum-Aligh 设计方法为:后两靶成直线.(八)、水平井设计Horizontal landing calculations 水平着陆点计算Select the method for calculating the landing point 选择计算着陆点(进入水平段)的方法.1、Landing type 着陆类型Final wellpath 着陆点轨道(参数)2、projection 设计点(计算.计划)参数3、Target plane 靶平面down dip 延伸井斜角direction 方位4、Next 下一段设计Add on another section after this one 添加下一段设计剖面(九)、从当前井底到靶点的设计project forward to a target 设计到一个靶点Select the target to project to (this is for information only)选择靶点设计到当前井底.六、Survey测量计算(井身轨迹计算表)(一)、Open survey 打开测量数据(二)、New survey 建立新的测量数据(三)、Delete survey 删除测量数据、(四)、Date Analysis 数据分析1、min/max graph 图表2、varying curvature 变化曲线Tolerance 公差Report 报表2d varying curvature graph 二维曲线图3d varying curvature graph 三维曲线图(五)、Export 输出1、units 单位2、column delimeter 列间隔blank 空白列tab 制表位user 用户设定间隔符3、clipbrd 剪切板(六)、Report 报表(二)、New survey 建立新的测量数据1、Survey setup- Create new survey 测量数据设置-建立新的测量数据,Survey 栏:填测量数据名, description 描述Company 公司 Engineer 工程师Start date 日期 survey tool 测量工具2、Tie-on point 连接点User 用户自定义点From wellhead 从井口为起始点From survey 从一个测量点开始3、Survey calculation method 测量数据计算方法Radius of curvature 曲率半径法Wellpath datum elevation 轨迹基准面4、Import 输入Import survey 输入测量数据Normal survey 正规(标准.正常)测量数据Inertial survey 无变化的测量数据Inertial survey – calculate MD/IAC/AZ 无变化的测量数据-计算斜深、井斜、方位,Column order 纵向按序排列Correction 修改There is no valid date in the clipboard 剪切板里没有有效数据Column delimeter 列间隔5、Survey editor – survey **测量数据编辑器-测量数据号Input validation 输入确认Max Dogleg 最大狗腿度6、Interp 插入Point interpolation 点插入Reference datum 基准点Notepad 记事本7、Project ahead 预测(1)、Free projection 自由预测To MD、TVD 以斜深或垂深来预测Apply: Build/Turn 定义井斜/方位变化率Apply: Dogleg/Face 定义狗腿度/工具面Apply: Trend over last N points 定义以前几个点的趋势来预测 (2)、TO target 预测到靶点landing point 落点栏,可以看到靶区坐标Initial hold Len 初始稳斜段长(3)、Back on track principal plan 依靠主轨迹预测Curve + hold 圆弧+稳斜Optimum Aligh 最佳圆弧-稳斜-圆弧七、Anticollision 防碰计算(一)、Offset wells 对比井.邻井Anticllision offset wellpath selection 防碰邻井轨迹选择Filtering : by type/by range /all 过滤方式有:类型/范围/全部Filter all 对所有的井按选择的方式过滤Filter selected 过滤被选择的井Inc principal plan 包括主设计(二 )、Interpolation interval 间隔设置1、Interpolate By : MD/TVD 以斜深或垂深为间隔2、Complete wellpath 全井轨迹扫描Depth range : from/to 井段扫描:深度范围从***---***米3、Interval 间隔距离4、Limit results by:限定计算范围Scan radius 扫描半径Ratio factor 比例系数Include stations 包括井口Include casing 包括套管5、Scan method 扫描方法Closest approach 3D 三维渐进球形模式(最近距离法)Travelling cylinder 园柱面柱状模式(法面)Horizontal plan 平面法水平面模式(平面)(三)、travelling cylinder view 法面图(四)、ladder view 梯形图(五)、ratio factor view 比例因数图(六)、3d proximity view 最近距离图(七). Spider view 蜘蛛网(水平)图(八).reports 报表.八、Utilties有效设置Graphics manager 图形管理器Options 选项Profile 剖面Spider 蜘蛛Travelling cylinder 法面Report manager 报表管理器Units 单位Unit change dialog 单位改变对话框Dogleg severity 狗腿严重度Magnetics 磁北极Geodetics 地理北极Site optimiser 地点Graph setup 图表设置User setup 用户设置 report setup 报表设置。

相关主题