HP-UX B11.11操作系统安装（详细安装）安装所需的介质和资料：HP-UX 11.11 Core OS Install/Update/Recovery光盘(1张)HP-UX 11.11 Support Plus光盘(1张)HP-UX 11.11 Application Software光盘(5张)1．安装前的准备：在系统的安装之前检查机器的各线连接，将机器通过网线接到hub上，并且在确保各个外设（磁带机.磁盘阵列等）加电后，然后再开机。
2．在屏幕上将看到："Processor is booting from fist availiable deviceTo discontinue.press any key within 10 second s"在10秒之内按任意键，之后屏幕将显示一9个命令集画面：Main Menu…………………………………………….Command DescriptionBoot[PRI|ALT|<path>] Boot from specified path……………………… ……………………………………………… ……………………………………………… ………………………Main Menu : Enter command >3．将HP-UX11.11 CoreOSInstall/Update/Recovery放入光驱或DVD,4．键入命令SEA，系统会查询硬件设备的物理路径：Main menu :Enter command >sea(例如)Path Number Device path Device TypeP0 8/4.5 Random access mediaP1 8/4.9 Random access mediaP2 … …………5.根据'device path如：8/4.5'与机器前门内标注（D250）确定光驱或DVD的路径，假设为P1 8/4.9键入命令bo p1回车：Main Menu:Enter command>bo p16 .系统会询问是否要进行交互访问，要输入 n回车Interact with IPL? > n注意： :接下来可能出现屏幕乱码现象,解决方法:按User System 键,屏幕底出现8个小亮块,最右边一块为按F8键,8个亮块发生变化,其中有一个为 ,按F5键, 进入TERMINAL CONFIGURATIONJIEMIAN界面，将TERM MODE项的值改为EM100）,然后按F1,保存设置7．系统要求选择安装方式：Welcome to the HP-UX installation/recovery process!Use the <tab> key to navigate between fields,and the arrow keysWithin e the <return/enter>key to select an item .Use the <return>or <spacebar>to pop-up a choices list.If theMenus are not clear,select the "Help" item for more information.[Install HP-UX ][Run a Recovery Shell][Advance Options ]选择[Install HP-UX]，回车继续。
8．屏幕出现： User Interface And Media OptionslllllllllSource Location Options:[*] Media only installation[ ] Media with Network enabled(allows use of SD depots)[ ] Idnite-UX server based installationUser Interface Option:[*]Guided Installation (recommand for basic installs)[ ]Advanced Installation选择[*]Media only installation和[*]Advanced Installation两项，[*] 为选中状态，然后OK. 8．屏幕出现:Basic Software System File system AdvancedConfigrations:[……………………………………….] [ Description…]Environment s:[……………………………………....] [HP-UX B.11.00][Root Disk….]……………………………………………………………File System :[Logical Volume Manager <LVM> with VxFS ][Root Swap(MB)]…… Physical Memory (RAM) =……[Languages…….]…… [Keyboards…] [Additional….]对于Basic中的内容不要做任何修改，保留默认值。
9．选中File System，显示如下(表中数据只是为例，有的数据被省略)Basic Software System File system AdvancedMount Dir Usages Size(MB) % used VG Name/stand HFS 84 24 vg00 [Add]Primary SWAP+D --- -- ---- [Modify]/ VxFS -- -- --- [Remove]Usage :[…..] VG name: [ ] Mount Dir :………..Size: [Fixed MB ]----- Avail:------[Add/Remove Disks…] [---Additional Task---]在这里可以修改各系统文件的空间大小Type Filesystem kbytes used avail %used Mounted on hfs /dev/vg00/lvol1 199381/200M 29440 150002 16% /stand*** /dev/vg00/lvol2 199381/2048M ***** ****** **% /***vxfs /dev/vg00/lvol3 258048/252M 152942 98537 61% /vxfs /dev/vg00/lvol4 1048576/1024M 1357 981768 0% /homevxfs /dev/vg00/lvol5 1048576/1024M 309329 693045 31% /optvxfs /dev/vg00/lvol6 512000/500M 1449 478642 0% /tmpvxfs /dev/vg00/lvol7 1048576/1024M 530219 485960 52% /usrvxfs /dev/vg00/lvol8 2097152/2048M 397013 1593881 20% /varvxfs /dev/vg00/lvol9 2097152/2048M 1776350 300752 86% /sybase根据要求设置各文件系统的大小与下表一致：Mount Dir L2000(MB) UsagePrimary swap xxx Swap+D/ xxx VxFS/stand xxx HFS/var xxx VxFS/usr xxx VxFS/Tmp xxx VxFS/Opt xxx VxFS/home xxx VxFS如果屏幕上的各个文件系统的缺省值与用户要求不一样，要进行修改，每次修改之后要按Modify项确认，以便保留设置。
设置完毕，GO,继续下一步。
10．接着系统会提示被安装的硬盘上的原有数据将被破坏，选GO，继续。
11．这时候系统文件的安装开始，屏幕显示，Loading configuration utilitys……..*Starting system configuration…….*…………………………………..………………………………………整个过程包括710个文件的安装，需要较长时间（大约2小时），请耐心等待，最后系统自动重启两次，显示大大的OK字样，提示安装成功。
12．重启后，，系统要求配置网络Are you ready to link this system to a network?Press[y]for yes or [n] for no .then press [Return]键入y，回车13DHCP：Do you wish to use DHCP to obtain networking information ?Press [y] for yes or [n] for no .then press [Return]键入n，回车14．系统询问是否继续下面的主机名、Ip地址、时间的配置：*Your system name (host name)*Your internet protocol (IP0 address.*Your time zoneAre you wish to continue (answering no will HALT the system)?Press [y] for yes or [n] for no .then press [Return]键入y，回车15．接着下一个画面底下两行将显示：Enter the system name ,,then press [Return].Just pressing [Return]will keep the (not recommended)name "unhost": root在光标处输入你想要的系统名，例如root然后回车然后系统询问是否正确：You have chosen root as the name for this system .Is this correct?Press [y] for yes or [n] for no .then press [Return]键入y，回车16．屏幕要求你选择你所在的位置：1） North America or Hawaii2） Central America3) South America4) Europe5) Africa6) Asia7) Australia,New ZealandEnter the number for your location (1-70then press [return]键入6，选择Asia ，然后回车17．接下来要求选择时间：Select your time zone from the following list:1)Western Russia 6)Phillipines,hongkong,Eastern China ,Taiwan2)India 7)Japan3)Pakistan 8)Korea9)Thailand 9)Unlisted time zone5)Singapore 10)Previous menuEnter the nunber for your tiiiiiime zone(1-10),then press [Return]键入6，回车继续系统会询问选择是否正确：Is this correct ?Press [y] for yes or [n] for no .then press [Return]键入y，回车18．屏幕显示：The current system time is --------------Is this correct?Press [y] for yes or [n] for no .then press [Return]看系统的时间是否正确，如果不需要修改，键入y，回车19．系统询问是否想设root的密码：Do you want to set the root password at this time?Press [y] for yes or [n] for no .then press [Return]键入y，回车，系统提示输入新密码，键入密码，回车继续20．系统要求输入IP地址：Enter your IP address,then press [Return]or just press [Return] to selectDefault address:输入IP地址，回车，屏幕出现：You have chosen------as the IP address for this system,Is this correct ?Press [y] for yes or [n] for no .then press [Return]如果觉得输入的IP没有错误，键入y，回车确认。