System Installation Guide GS-SR101T1U Rack Mount Server SYSTEM INSTALLATIONGUIDE1-iSystem Installation Guide 1. INTRODUCTION1.1. PrefaceUsing this manual will help you get the most from yourRack Mount Server. Keeping the manual with your RackMount Server to refer when you want information andhelp.In order to get the optimal usage out of your Rack MountServer and you should remember the following:Read through all the instruction for your RackMount Server .Keep the area free of static electricity and magnetic fields. These can damage the Server .When cleaning the server or its components, apply the proper cleaning solution or sprays only on thecloth ,not to the server or its components .1.2. FeaturesOur Rack Mount Server use 1U Chassis and support thefollowing features:Processor SupportDual Socket 370 for Intel FC-PGA Coppermine and Tualatin processor Up to 1 GHz and aboveOptimal CPU Keep Out Zone for Type C Heat-sink100/133MHz FSBAUTO detect CPU voltageBIOSAMI BIOS on 4M bit flash ROM1-1System Installation Guide Auto configure IDE HDD typeMultiple boot optionsUser setting for hardware monitoringDMI 2.0 compliantChipsetVIA Apollo Pro Family AGP set( VT82C694T ,VT82C686B ) ChipsetATI Rage XL 2X VGA Chip with 8MB Video MemoryPROMISE PDC20265R with RAID 0 or 1 support Dual Intel 82559 LAN chipMemory SupportFour 25 degree angled 168 Pin DIMM sockets for SDRAM modulesSupports up to 2GB PC-100/PC-133 ErrorChecking and Correction (ECC) either un-bufferedor registered memory and VCM SDRAMSupports only 3.3V SDRAM DIMMStorage ControllerMax 4 IDE ATA channels ( 2 x ATA-66 and 2 x ATA-100 for IDE RAID 0 or 1 )Support front-accessible 2 hot-swap drives featuring IDE ATA-100 transferring rate44MB Floppy Disk Drive ( Slim type )High Speed IDE CD-ROM Drive ( Slim type)NetworkingOn board dual LAN, Ethernet 10/100 WOL (Wake1-2System Installation Guide On LAN)Adaptive fail over featureLoad balance featureI/O Expansion SlotPCI raisers , 1 slot ,support 33MHz & PCI 2.2 compliantBuild-in I/O ports1 x PS/2 Keyboard port1 x PS/2 Mouse port1 x COM port1 x VGA port1 x LPT port2 x RJ-45 ports2 x USB portsPowerTotal output power 250 WInput : Rating switch full range 90V~250V 47~63 HzOperating Temperature5 to 40 degree CThermal SolutionSpecial-designed Heat-sink and hi-efficiency chassis fans for dual 1 GHz plus processor thermalsolution1-3System Installation Guide Other FeaturesSupport Wake On LAN ( WOL )Support External Modem Ring OnOptional DOC solution for embeddedInternet/Networking ApplicationsO/S SupportWindows NT ,Windows 2000 ,Linux ( RED HAT7.0 , Netware 5.0Chassis DimensionsHeight 44.45 mm ( 1.75 In. )Width 482.6 mm ( 19.0 In. )Depth 609.6 mm ( 24.0 In. )System weight 11.8 Kg ( 26 lbs )1-4System Installation Guide2-12. Hardware InventoryWhen you unpack your GS-SR101 Rack Mount Server, Check that all the items that you ordered are present in good condition. Review the inventory checklist below to be sure that the components and optional components that you ordered are included. If anything is miss or damage, contact your retailer as soon as possible.ChassisPower Supply ( Installed )Motherboard GA-6VTXDR ( Installed )Manuals (M/B user’s Manual & SystemInstallation)Hard Disk Drive Tray x 2Flat Screw # 6-32 * 5L x 12 ( For HDDs)Fan + Heat sink x 2Case Handle x 2Flat Screw M4*10L x 4 ( For Handle )Support CD x1Support Floppy Disk x 2Fig-1Fig-2 3-1Fig-3System Installation Guide3-3Figure 4Figure 6System Installation Guide3-63.4. System RAM InstallationThe motherboard has 4 Dual Inline Memory Module(DIMM) sockets. The BIOS will automatically detect memory type and size. To install the memory module, just push it into the DIMM slot. (Fig-8 )Fig-8System Installation Guide3-73.5. InstallingHandleGet Handle and screw from the accessories box. Andthen mount the handle on the front panel .( Fig-9 & Fig-10 )Fig-9Fig-10Fig-11 Fig-12Fig-13HDD Data Cable Pin 1Fig-143-9System Installation Guide3-10After the above step, mount HDD to HDD tray with the screw ( Fig-15 ) ,and put HDD tray into the chassis .( Fig-16 )Fig-15Fig-16System Installation Guide3-11When you put HDD tray into the chassis, make sure that the lever is ata 90 degree angle to the chassis .( Fig-17 )Otherwise ,damage may occur to lever. After that push HDD tray to chassis carefully and make sure the HDD tray is click into Chassis. (Fig-18)Fig-17Fig-18Fig-19If you do not making sure that the lever is at a90-degree angle to the Chassis ,the HDD tray click may be damage .( Fig-20 )HDD Tray ClickFig-203-12System Installation Guide3-13 When you put HDD tray into the chassis ,make sure there is a no gap between HDD tray andchassis .Otherwise the system can’t detect the HDD .(Fig-21 )Fig-21HDD1 LED HDD2 LEDFan LEDPower LEDPS/2 Keyboard LAN1 ( RJ-45 )。