ATC-command or T-command has been given when ATC is not in home position.
EX0165
TOOL CLAMP SIGNAL OFF
PER0165
Tool clamp check signal has been turned off while spindle is rotating.
面板报警
MER0099
在平板式操作面板中已经发生了报警。
EX0103
INTERLOCK BYPASS ON
PER0103
ATC-command has been given while interlock bypass is on.空管指挥?已经?被?给?而?联锁?旁路?是
EX0116
REFERENCE POINT PARAMETER ERROR
#2尾座没有夹紧
PER0305
当尾座并未夹紧时，就已经发出了一个T指令。（第2床头箱）
EX0320
多边形模式
PER0320
在多边形模式期间，就已经发出T指令。
EX0322
尾座没有夹紧
PER0322
当尾座并未夹紧，就已经发出了一个主轴前进/后退、旋转刀具主轴前进/后退、旋转刀具连接检查指令。
PER0116
X-or Y-or Z-axis 3rd zero-point has not been properly set at parameter.或?Y-或?Z轴?第三?零点?已经?不?被?妥善??在?参数设置。
EX0123
NO EMPTY POT IS EXISTING
PER0123
No empty pot exists during ATC cycle. Check the tool data.没有?空?锅?存在??ATC?周期期间。?检查?的?工具?大
EX0020
编辑键开关接通
PER0020
编辑键开关接通着，就已经起动了循环开始。
EX0021
TOOL IS NOT CLAMPED
PER0021
A cycle start has been activated with the tool is not clamped.EX0023起动锁信号接通PER0023
PER0296
Alarm of servo motor(magazine).
EX0298
POT STAY ON MAGAZINE
PER0298
The pot has been held at indexed position of magazine during returning cycle. Spindle or next tool data may be missetting in the parameter.
EX0301
不正确T代码指令错误 #2
PER0301
已经发出了第2床头箱转塔刀架工位数之外的T指令。
EX0302
不正确T代码指令错误
PER0302
已经发出了转塔刀架工位数之外的T指令。
EX0303
转塔刀架短推入分度模式
PER0303
在转塔刀架短路径分度模式期间，就发出了转塔刀架前进或后退指令。
EX0305
当已经输入了一个外部开始互锁信号时，已经起动了一个循环开始。
EX0024
卡盘没有夹紧
PER0024
卡盘没有夹紧，就起动了循环开始。
EX0026
请关门
PER0026
没有关门，就起动了循环开始。关门。
EX0029
尾座活动套筒没有伸出
PER0029
在尾座缓动期间或尾座主轴没有OUT（伸出）时，就已经起动了一个循环开始。
EX0169
ATC SHUTTER IS NOT CLOSE
PER0169
The cycle start button has been pressed with ATC shutter open.
EX0201
INPROPER T-CODE COMMANDED
PER0201
The specified T-code command is incorrect.
EX0210
SBC CYCLE TIME OVER
PER0210
SBC cycle time over
EX0218
TOOL DATA SETTING ERROR
PER0218
T-code has been specified with condition on that the data other than number of tools in magazine has been set to spindle tool data or waiting pot tool data. This is a tool data setting error.
Number of tools is not properly set in the parameter.
EX0256
MAGAZINE INDEX TIME OVER
PER0256
Magazine indexing cycle time has been over.
EX0296
SERVO ALARM (MAGAZINE)
EX0013
主轴或旋转刀具主轴接通
PER0013
在主轴或旋转刀具主轴旋转期间，就已经发出了一个自动门打开指令。
EX0018
所有的轴都需要回零
PER0018
在机床锁紧取消之后，没有进行所有轴的回零，就起动了一个循环开始。
EX0019
工件计数器处于满数
PER0019
PC或外部工件计数器已经数满时，还是起动了一个循环开始。
EX0139
ATC CANNOT POERATE WITHOUT TOOL INSPINDLE OR STANDBY
PER0139
The ATC command is specfied in states that the tool is not at the spindle or the standby position.
EX0035
切断不完全
PER0035
切断还没有完成。
EX0068
互锁释放超时
MER0068
门互锁取消状态已经失效。
EX0069
门互锁超时
MER0069
在定时器中所设定的经过时间之后，就已经接通了门锁紧完成信号。
EX0097
面板I/O报警
MER0097
在平板式操作面板中已经发生了I/O报警。
EX0099
EX0160
ATC NOT IN HOME POSITION
PER0160
M03,M04. or rigid-tap command has been given when ATC is not home position.
EX0161
ATC ARM NOT IN HOME POSITION
PER0161
EX0231
PLEASE CLOSE THE MAGAZINE DOOR
PER0231
The magazine door has been opened. Close the magazine door.
EX0233
PLEASE PRESS CYCLE START BUTTON
PER0233
Press the cycle start button. T-cycle is started.
PER0135
An empty pot does not exist even if the spindle tool data is not "0". Check the setting data again.的?ATC?命令?是指定在美国????，?的?工具?是?不?在?的?主轴?或?的?待机?位置
EX0126
EMPTY POT IS EXISTING
PER0126
An empty pot exists even if the spindle tool data is "0". Check the setting of tool data again.一个?空?锅?存在?甚至?如果?的?主轴?工具???数据是“0”。?检查?的?设置?的?工具?数据?再次。
EX0124
SPECIFIED POT IS NOT INDEXED
PER0124
The pot specified by T-code has not been indexed at change position during ATC cycle.的?锅?指定的??T-CODE?已经?不?被?索引?在?改变? ATC?周期中的位置。
EX0230
PLEASE SELECT MAGAZINE AUTO MODE
PER0230
The manual operation mode has been selected on the magazine operation panel when T-code command has been given. Selected the automatic operation mode.
EX0147
ATC DATA ERROR
PER0147
G361(ATC) was commanded without dammy holder./T** was commanded without LBB-MG home position./G361(LBB) was commanded without special tool(LBB adapter tool)/B-axis commanded with LBB holder.