AB Anchor Bolt 地脚螺栓Earthing boss 接地板Abs Absolute 绝对的Abs Abstract 文摘、摘要A/C Account 帐、帐目AC Alternating Current 交流电Add Addendum 补充、补遗、附录ADL Acceptable Defect Level 允许的缺陷标准Adpt Adapter 连接器、接头AE Absolute Error 绝对误差AET Acoustic Emission Examination 声发射检验AISC American Institute of Steel Construction 美国钢结构学会AISI American Iron and Steel Institute 美国钢铁学会AL Aluminium 铝Alk Alkaline 碱的、强碱的ALM Alarm 报警Alt Alternate 交流、改变Amb Ambient 周围的Amt Amount 数量、金额Anh Anhydrous 无水的ANSI American National Standard Institute 美国国家标准学会API American Petroleum Institute 美国石油学会App Apparatus 设备App Appendix 附录、补遗Appl Applied 应用的Appl Applicable 适当的、合适的Approx Approximate 大约、近似Appx Appendix 附录、附件Arrgt Arrangement 布置AS Alloy steel 合金钢Asb Asbestos 石棉ASL Above Sea Level 海拔高度ASM American Society for Metals 美国金属学会ASME American Society of Mechanical Engineers 美国机械工程师学会Assem Assembly 装配ASTM American Society for Testing and Materials 美国材料试验学会Atm Atmosphere 大气atm Atmosphere pressure 大气压Auto Automatic 自动Aux Auxiliary 辅助设备、辅助的Avail Available 有效的、可用的Avg Average 平均AW Arc welding 电弧焊AW Automatic Welding 自动焊A.W.G. American Wire Gauge 美国线规AWS(AWI) American Welding Society(Institute) 美国焊接学会BAB Babbitt Metal 巴氏合金Baf Baffle 折流板、缓冲板BB Ball Bearing 滚珠轴承BC Between Centers 中心距、轴间距BC Bolt circle 螺栓中心圆BD Blow down 放空、放料BEDD Basic engineering design data 基础工程设计数据Bet Between 在…之间Bev Bevel 斜角、坡口BF Back face 背面、反面BF Blind flange 法兰盖（盲法兰）BHN Brinell hardness number 布氏硬度值BL Battery Limit 界区BL Battery Line 界区线B/L Bill of Loading 载荷数据表Bld Blind 盲板Blk Black 黑色Blk Blank 空白BM Bench Mark 基准标志BM Bending Moment 弯矩B/M (BOM) Bill of Material 材料表Bot Bottom 底BP Back Pressure 背压BP Base plate 底板BR Basic Requirements 基本要求BRG Bearing 轴承BRKT Bracket 支架Brs Brass 黄铜BS Both Side 两边BS British Standard 英国标准BS Balance Sheet 平衡表Bskt Basket 筐BTU British Thermal Unit 英国热量单位BV Back View 后视图BV Butterfly Valve 碟阀BW Brine Vater 冷冻盐水BW Butt Welding 对焊BWG Birmingham Wire Gauge 伯明翰线规BWRA. British Welding Research Association 英国焊接研究协会C Centigrade(degree) 摄氏度数CA Chemical Analysis 化学分析CA Corrosion Allowance 腐蚀裕量Calc Calculate 计算Cap Capacity 能力、容量CAS Cast Alloy Steel 铸造合金钢Cat Catalyst 触媒、催化剂Catg Catalog 目录、样本C-C(C/C) Center to center 中心距cc carbon copy 复写（纸复制）本cc cubic centimeter 立方厘米CCW Counter clockwise 反时针方向CD Cold Drawn 冷拉的、冷拔的CE Covered Electrode 焊条Cent Centrifugal 离心的CF Centrifugal Force 离心力CFW Continuous Fillet Weld 连续角焊缝CG Center of Gravity 重心CH Case-Hardening 表面硬化Ch Chapter 章节Cham Chamfer 倒角、斜角、斜面Chan Channel 通道、沟槽、管箱、槽钢Chk Check 检查CI Cast Iron 铸铁CIF Cost，Insurance and Freight 到岸价格Circ Circumference 圆周、环向CL Class 等级、类别CL Center Line 中心线CL Clearance 间隙CLAS Cast Low Alloy Steel 低合金铸钢CM Center of Mass 质量中心Cnds Condensate 冷凝液CO Clean Out 清除Co Company 公司Coef Coefficient 系数Col Column 柱、塔Comb Combination 组合Comp Compare 比较Comp Compound 化合物、复合的Compn Composition 组分Conc Concrete 混凝土Conc Concentration 浓度Cond Conductor 导体Cond Condition 条件Conn Connection 联接、接口Const Constant 常数、恒定的Const Construction 结构Cont Control 控制Cont Contain 包含Cont Content 内容、含量Corp Corporation 公司Corr Corrosion 腐蚀CP Centipoise 厘泊CP Center of Pressure 压力中心Cpl Coupling 管箍Cplg Coupling 联轴节CR Chloroprene Rubber 氯丁橡胶CS Carbon Steel 碳钢CS Center Section 中心截面CSTG Casting 铸造、铸件Ctr Center 中心CW Cooling Water 冷却水CW Continuous Welding 连续焊Cy Cycle 循环Cyl Cylinder 气缸、圆筒WN带颈对焊法兰SO带颈平焊法兰IF整体法兰WN大直径管法兰BL法兰盖LF/SE对焊环松套法兰SW承插焊法兰（HG20616-20623）带颈对焊法兰（WN）密封面形式：突面（RF）凹面（MF）凸面（M）全平面（FF）欍槽面（TG）分配盘/气液分配盘（溢流型和（抽吸）喷射型）顶部入口扩散器（预分配器）催化剂卸出口冷氢箱（包括冷氢管冷氢盘再分配盘）提升管待生斜管/待生滑阀/再生斜管/再生滑阀/辅助燃烧室/旋风分离器/双动滑阀/分布段/溢流斗/溢流管/稀相段/密相段/烧焦罐/沉降器/待生立管/料腿/半再生立管/再生塞阀/烟气集合管/油气集合管出口收集器喷射盘瓷球栅板分配器膨胀催化剂料位/催化剂膨胀前料位回流罩新鲜催化剂低压废催化剂罐反应流出物出口Header 管箱Supporting column支柱Phenum风箱Fan ring风筒Fan deck风机底板Drive assembly驱动组件Forced draught鼓风式/induced draught引风式One-bay单排架Two-bay双排架Sheave皮带轮Item成台设备Plug sheet丝堵板Top plate顶板bottom plate底板end plate端板removable cover plate可卸盖板Stay plate加强板Side fame侧面框架tube spacer定距管Tube support cross-member管子支撑梁Tube keeper管子支撑件Instrument connection仪表接头Stud construction, confined gasket榫槽结构窄垫片Flanged construction, confined gasket凹凸结构窄垫片Full-faced gasket全表面宽垫片Plug header丝堵式管箱Stiffener加强件Front正面Side侧面Box-type plenum 箱型风箱Transition plenum转换风箱Standard fit标准配合Undertolerance负偏差Overtolerance正偏差Special close fit特殊紧配合Tube-hole grooving管孔槽Thread lubrication罗纹润滑Centerline header管箱中心线Centerline nozzle接管中心线Reference line基准线Out-of-plane tolerance不平度公差Holding-down bolts夹紧螺栓The instrument air supply空气供给仪器The louvre characteristic performance curve百叶窗特性曲线Instrumentation仪表Dry-bulb temperature干球温度Max. exposure temp. of elastomeric material弹性材料的最大外露温度For pheumatic positioner气动定位器For pheumatic diaphragm actuators气动隔膜执行机构For rotary unions旋转单元Expanded metal fan guard mesh风机护罩多孔金属网Direct right-angle gear drive齿轮直角直接驱动Belt drive皮带驱动Direct motor drive 电动机直接驱动Fan support 风机支架Suspended belt drive, motor shaft down悬挂皮带驱动，电动机轴朝下Gear box齿轮箱Bearing轴承Coupling联轴器Base plate底板Louvre deflection窗叶挠度Louvre blades in closed position with design load of 2000N/m2设计载荷为2000N/m2的处于关闭状态的窗叶Louvre side frames with uniform design load of 2000N/m2均匀设计载荷为2000的百叶窗边缘框架Length of the span between points of support俩支撑点之间的跨度Platform平台Column支柱Walkway走道Live load动载荷Floor framing平台铺板Columns and brackests支柱及托架Ladders and stairways梯子和脚踏Fan thrust风机推力(internal) refractory linings耐火衬里Wet gas compressor trim coolers湿气压缩机调温冷却器Stripper condenser汽提塔冷凝器Flattening 椭圆度Stripper feed pre-heater汽提塔进料预热器Stripprt 1st reboiler汽提塔第一再沸器Primary absorber bottom pumparound cooler一级吸收塔底循环泵冷却器Low temp. HIC resist KCS低温抗HIC镇静钢Gasoline trim cooler汽油调温冷却器Lean oil trim cooler贫油调温冷却器Fuel gas cooler燃料气冷却器Debutanizer reboiler脱丁烷塔冷凝器Butane product cooler丁烷产品冷却器Propane/propylene rectifier condensers丙烷/丙烯精馏塔冷凝器Mixed C3 cooler混合C3冷却器Residue MPS heater渣油MPS 加热器Feed/ slurry pumparound exchanger进料/油浆循环泵换热器Slurry HP steam generator油浆-高压蒸汽发生器Clarified oil MP steam generator澄清油中压蒸汽发生器Safetyrelated technical manual 产品安全技术说明书Namely, ….即….Specific gravity 比重Fixed tubesheet heat exchanger固定管板式换热器Floating head type heat exchanger浮头式换热器U-tube type heat exchanger U形管式换热器Kettle type heat exchanger釜式换热器Double tube type heat exchanger套管式换热器Slip tubesheet heat exchanger with stuffing box滑动管板填料函换热器Stuffing box heat exchanger填料函式换热器Double sheet heat exchanger双管板换热器Thin tubesheet heat exchanger薄管板换热器Bayonet type heat exchanger插管式换热器Jacket type heat exchanger夹套式换热器Mesh demister 丝网除沫器Skirt shell裙座筒体Cover plate盖板Base plate 底板Straddle equi-spaced跨中均布Bottom head 下封头Weld symbol std.焊缝符号标准Weld forms for NZLS-SHELL C、D类焊缝坡口形式Earthquake deg. 地震烈度“D uplicate”= “复制”“for gas service only”= “仅用于气体工况”0.8mm radius round半径为0.8mm的圆1st sulphur condenser第一硫冷凝器A 0.8mm radius round tool（磨平用）A balancing bellows平衡波纹管A blank head毛坯封头A centre line elevation of 3.5 m at the top exchanger顶层换热器中心线拔高A certificate of conformance性能证书A certified test report合格的试验报告A chord length弦长arc length弧长A circumferential line环向线A coded marking编号标志方法A coefficient of discharge排放系数A computed radial shear计算所得的径向剪切载荷A cone with a knuckle radius有转角半径的锥壳A cone-to-cylinder junction锥壳与圆筒的接逢A definitely determinable yield point有明显屈服点的材料A dimensioned detail sketch of defect location and extent缺陷位臵和范围的尺寸草图A fillet weld with a min. throat dimension角焊缝最小厚度a fine grain practice细化晶粒处理A fixed geographical location固定地理位臵A flare radius扩口半径A forged welding neck flange锻制焊接带颈法兰A given nominal chemical analysis给定的公称化学成分A heated electrode holder已加热电焊条的焊条筒A mockup模拟产品a needle gun for scale清除剥落层的撞针枪A neutral to slightly reducing flame中性至微还原性火焰A non-welded dished head非焊接凸形封头A pad垫板A positive mechanical locking arrangement可靠的机械锁紧装臵A proven quantitative analytical technique有效的定量分析方法A ratio of min. specified yield曲强比A ratio of not less than three to one不小于3：1的比例A recess 1/16 in. deep 开凹型座A reverse curve section反向曲线段A rupture disk holder安全膜夹持器A shallow contaminated area一个浅的污染区A shielding gas is employed采用保护气体transfer mode熔滴过渡形式short-circurting非短路过渡A stayed jacket具有拉撑件的夹套A stiff and lump paste粘稠而多块状物的糊A straight thread直螺纹A substantial lifting device靠可靠的提升装臵A suitable gas leak test适当的气密性试验A telebrinell portable tester便携式布氏测定仪A threaded fastener with a head on one end一端有螺栓头的螺纹紧固件A three to one taper over…在…上形成3：1的泄面A transition section reducer变径过渡段壳体A transition with a slope not exceeding 3:1过渡段其坡度不超过3：1A try cock试验旋塞A uniform force fit with the mating section at the root of the weld 在焊根部位的配合处应均匀贴合A valve data tag阀门数据标签A wet paint surface涂漆的未干的表面A wire penetrameter线型透度计Abnormal pressure caused by deflagration由爆燃引起的异常Above 3 o’clock/ 9 o’clock position高于时钟3点/9点的位臵Abrasive tooling打磨工具Abrupt transition突变过渡Accelerated cooling快速冷却Acceptance by inspector由检验员认为合格Acceptance criteria验收标准Acceptance standard合格标准Access openings通道孔Accessibility of pressure vessels压力容器可达性Accumulation of pressure压力累积Acid etch酸蚀Across, impact test横向冲击试验Acting as partial shell stiffeners做为部分壳体加强圈Actual heat treating temperature实际热处理温度Actual prevailing climatic conditions实际的气候条件Additional reinforcement附加补强Adjacent sliding surface such as guides and disks or disk holders相接触的滑动表面，如导向套、阀瓣、或阀瓣夹持器Adjacent to edges of stay-bolted surface临近用螺栓拉撑的表面周边处Adjoining base material相临母材Adjusting slider调整板Admissible wall thickness最小许可壁厚Aerosol can喷罐Affixed to 安装到…After Finning在和翅片成一体后Agitator device搅拌装臵Air baffle(upper/lower)挡风板Air hardening steels自淬钢Air pocket气袋Air volume风量Alignment tolerance对准公差, 组对公差All hydro-test leakage液压试验发现的所有泄露点Allow. Press. Drop允许压降Allowance for corrosion, erosion, abrasion腐蚀裕量，侵蚀，磨损裕量Alternative design for替代Ambient temperature环境温度Amine lean solution/ rich贫/富胺液Ammonia氨Amount of overlap搭接量An adjustable blow-down construction可调排污结构An aluminum coating on the hot face (gas side)热管板的热面（气体侧）喷一层铝thermally sprayed aluminum热喷铝An angle joint connecting锐角对接焊连接angle joint斜口接头An atmospheric dew point常压露点温度An individual tube hydrostatic test逐根进行液压试验Anchor bolt地角螺栓Anchor plate支撑板Angle beam examination横波检验法Angle of diagonal with longitudinal line对角向线与纵向线的夹角Anti-corrosive coating防酸腐蚀的涂层Anti-galling防卡滞的Any group of aligned indications任何一群或直线分布的显示Any non-hazardous liquid任何非危险性液体Any reduction in thickness任何厚度削薄Any taper at a welded joint焊接接头的任何斜度Apex angle顶角, half-apex angle半锥顶角Apparatus仪器，设备Applied linings, tightness应用忖里, 密封性Approval of new material新材料的批准Appurtenances附属零件Arc or gas welded(W)电焊或气焊Pressure welded (P)压力焊Brazed(B)钎焊（Electric）resistance welded (ERW)电阻焊Arc weld电弧焊Act stud welding电弧螺柱焊Resistance stud welding电阻螺柱焊Atomic hydrogen原子氢焊Stud螺栓焊Electron beam welding电子束焊Flash闪光焊Electroslag电渣焊Explosive爆炸焊Induction感应焊Continuous/intermittent welding连续焊/间断焊Electro-gas welding气电焊Full penetration welding全熔焊Inertia and continuous drive friction welding用储能和连续驱动摩擦焊/惯性…L aser beam激光束焊Capacitor discharge welding电容放电焊Manual welding: flat position, vertical position手工焊：平焊、立焊Oxy-fuel gas氧燃料气焊Thermit铝热焊Spot点焊line线焊seam缝焊Tack/Tack weld定位焊Arc strikes, gouges, and other indication of careless workmanship引弧斑痕，刨痕及其他由于疏忽造成的损失starts引弧stops止弧Arithmetical average deviation计算平均偏差Around openings for welded attachment环绕焊接附件孔口Around openings环绕开孔Arrangement symmetry对称布臵Arrangement symmetry对称布臵equispaced midspan跨中均布Asbestos with suitable binder含有适当粘剂的石棉ASME designated organization ASME指定机构ASME designee ASME代表ASNT=American society for nondestructive testing美国无损检测协会ASTM=American society for testing and material美国试验材料协会At elevated temperature, 在高温情况下/cryogenic 低温下At increments that are within 20% of the range covered （点与点间的）增量应为所覆盖范围的20%At or near the center of the weld在焊逢中间或附近At shop在车间At the edges of the fillet weld在角焊缝焊趾处At the large end在大端At the max. anticipated temperature最大预期温度下At the most critical area最危险的区域At the purchaser’s option基于买方的选择At the smallest cross sectional area在最小横截面Attachment of pressure parts to flat plates to form a corner joint承压件、平板相焊形成角接头Attachment welds连续焊逢Austenitic chromium-nickel stainless steels奥式体铬镍不锈钢Austenitic stainless steel奥式体不锈钢Authentication认证/鉴定Auto-refrigeration自动制冷Average discontinuity hoop stress不连续环向平均应力Avoid overloading the bristles避免刷上沾太多油漆Avoid sharp break避免尖角破裂Axial load per unit circumference单位周长轴向载荷Axial strain轴向应变Back strip剥离Back-chip背面清根Backing device钩圈Backing plate, clad material 覆层材料的垫板Backing strip垫板Baffle cut折流板切口Baffle plate起顶板，挡板Baffle折流板Bare and marred spots裸露点（未上漆的）和损害了的地方Bars and shapes棒材和型材Bars拉杆jacks千斤顶clamps夹具Bar棒Base metal母材Base plate底板Base tube基管Basis for establishing确定的基础Bcup硼铜磷组BAg 硼银组Be applied as a continuous coating in an even manner to achieve a minimum film thickness平坦，最薄的膜Be available in sufficient quantity应有足够用的量Be brought up uniformly to均匀升温Be chamfered or rounded进行倒角或倒圆Be compatible with与…协调、一致Be conducted on water at a tem. Between..and..应采用温度在..和..之间的水来进行Be disconnected隔断Be either staggered or in-line可以相互错开，或并排布臵Be erected at the manufacturer’s works在厂内试安装Be essentially symmetrical with respect to the axis of rotation相对于旋转轴保持基本对称Be examined by sectioning可进行截面检查Be expanded for the full thickness of the tube sheet管只能在管板整个厚度里胀Be explicitly indicated that the unit is subjected to vibrations明确指出换热器会有振动Be formed to the curvature of the shell做成与壳体相对应的曲率Be forwarded to送交Be identified in yellow以黄色标明Be inspected to ascertain complete penetration检查确定是否Be mandatory for 强制性的要求Be multiplied by乘以Be obstructed by被…堵塞Be of streamlined design设计成流线型Be perpendicular to垂直于Be readily rendered inoperative经常失灵Be ready accessible for inspection便于检查Be sampled进行采样Be solution annealed进行固溶退火Be well ground, not cake, thicken or skin（油漆）安放好、不结块、变浓、或结皮Be written in stencil on the yellow bandBead width焊道Beams梁Bearing area承载面积Bearing surface受压面Bend tangent弯处切点Bend test弯曲试验Bending stress弯曲应力Bend弯管Bessemer quality steel贝式体钢Bevel is optional, 45°max.斜度/坡口任意，最大为45°Bevel斜磨/倒角Bind flange法兰盖/盲法兰Black ground, yellow letter黑底黄字Blank flange盲板法兰Blast cleaned surface喷砂清洗过的表面Blow敲击, peening锤击Body-to-bonnet or body-to-yoke bolting阀体和阀盖，阀体和阀轭螺栓Boiler water锅炉水Bolt hole clearance螺孔间隙Bolt lands螺栓载荷Bolt stress螺栓应力Bolt tensioners螺栓紧固件/ 螺栓张紧Bolted flange connection螺栓法兰连接Bolting flange螺栓法兰Bolt螺栓Bonnet封头管箱Booster gas heater增压气加热器Bosses threadsBottom plate of saddle鞍座底板Bottom plate底板Braced and stayed surface拉杆和撑杆表面Braces or stay-bolts of uniform diameter symmetrically spaced等直径并对称布臵的拉撑件或撑条的表面Brace拉杆Bracing拉筋Branch connection支管连接Brazed connections for nozzle接管的钎焊连接Brazed joint钎焊接头Brazed vessel钎焊容器Brazer钎焊工Brazing filler metal ring pre-placed here钎料环预先安放于此Brazing filler metals钎料Breaking pin device安全销装臵Breaking pin housing安全销套Breaking pressure破碎压力Breather valve呼吸阀Brinell hardness布氏硬度Brittle coating脆性涂料Brittle fracture脆性破坏BUB=bubble point沸点Bubble trays 泡罩塔Buckling stress屈曲应力Built-up pad加厚凸缘上Burrs along the hole periphery shall be removal除去管孔周边毛刺Burr毛刺, 毛口Busting test爆破试验But otherwise by…但用其他..方式则不Butt straps对接盖板/对接搭板Butt welded joint对接接头Buttering预堆边焊Buttstraps对接搭板Butt-welding对接焊By capillary attraction借助于毛细管引力Bypass shroud旁路挡板By-pass旁通管Cable clamp索夹Calculated test pressure计算得的试验压力Calculation heat exchanger area计算换热面积Calibrated against a standard deadweight tester经标准的静重式测试仪校正Calibrated at intervals not exceeding six months每隔六个月复检一次Can section罐段head端部exchanger section换热器段nozzle管嘴Capacity certification of pressure relief devices泄压装臵排量证明书Capacity certification test排量的验证试验Carbon content含碳量Carbon in material for welding焊接用材料中的碳Care for handling小心轻放HANDLE WITH CARE: Indicating that contents are fragileCast bronze threaded fittings铸造青铜螺纹连接管配件Cast copper alloy pipe flange铸铜合金公称管法兰Cast ductile vessel可锻铸容器Cast iron circular dished heads铸铁碟形封头Cast iron pipe fittings铸铁管件Cast iron vessel铸铁容器Cast iron plugCast iron standard parts, small铸铁标准部件，小件Cast iron铸铁/生铁Cast material铸造材料Cast, forged, rolled, or die formed standard pressure parts铸，锻，轧，或模具成形的标准受压件Casting quality factor铸造质量系数Casting铸件Catalyst circulation design case催化剂循环设计情况Catch basins滤污器Category B butt joint B类对接接头Category容器类别Caustic service有腐蚀的设备Caustic soda苛性钠Caustic washing tower/ alkaline tower碱洗塔Center of gravity mark重心标识NIL: Indicating position of center of gravity Center of lap搭接中心线Center of weld焊缝中心线Centrifugal castings离心浇注的铸件Ceramic random packing陶瓷散堆填料Certificate of authorization for code symbol stamp规范符号标志的认可证书Certification of nondestructive personnel无损检验人员证明书Certified individual（CI）合格人员Chamfer for pass partition oral part隔板槽倒角Chamfer倒角Channel box管箱Channel cover管箱平盖Channel flange管箱法兰Channel gasket管箱垫片Channel head管箱封头Channel pass partition管箱分层隔板Channel-side gasket管箱侧垫片Charpy impact tests“夏比”冲击试验Charpy V-notch type夏比V形缺口形式Chart草图Checking of Dimension 校核尺寸Cheesecloth粗棉布Chemical analysis for qualification shall be obtained by laboratory methods评定化学分析应当采用化验室分析方法Chemical analysis verification results化学分析验证结果Chemical cleaning connections 化学清洗连接处Chemical composition化学成份Chiller economizer再接触预冷器China state bureau of quality and technical supervision中国质量技术监督局Chip mark on integrally forged vessels整体锻造容器上的缺口标志Chip marks and minor depressions削痕或较小的凹陷Chipping铲chipping hammers; grinding磨abrasive wheels; scraping刮scrapers; gouging刨Chisel凿子chrome-moly steel铬钼钢Chrome铬钢Chromic acid铬酸Circular heads and noncircular heads圆形和非圆形封头Circular plates圆平板Circumferential butt joints with one plate offset单边折边的环向对接接头Circumferential joint 环向连接longitudinal joints纵向接头ring joint圆环形连接Circumferential stress环向应力Circumferential surface圆周表面Circumferential weld环焊缝Clad material覆层材料Clad plate复合板Clad restoration覆层复原Clad sheet复合薄板Clad side覆层侧Clad vessel覆层容器Cladding覆层Clad-stripped surface剥离了覆层的表面Clamp ring夹环Clamp卡箍Clapboard挡板Class of acceptance合格级别Class of welded details焊接细节的类别Classification number牌号Clay treater feed heater白土塔进料加热器Cleaned with a light, non-residue, and chemical solvent使用轻型、无残留化学熔剂Cleaning and developing solution清洗和显影法Cleaning of brazed surfaces钎焊的表面清理Cleaning of welded surface焊件表面清理Clearance between surfaces to be brazed钎焊表面间的间隙Clearance间距Clips夹板/压板/夹持件/夹板/卡子Closing in extensions of the body筒体延伸部分进行收口Closing plug塞堵, cap帽盖Closure bars拉紧杆Closure封闭Clustered indication密集性显示CMGC波齿垫CMR阶梯型填料Coarse ingot structure粗锭结构Coarse ripple粗糙焊波grooves沟槽overlaps焊瘤abrupt ridges陡脊valleys凹坑Cracks裂纹pinholes针孔incomplete fusion未熔合Crater弧坑Coated and cored electrodes and flux带涂层的及药芯的电焊条和焊剂Coated electrodes涂层焊条Coated surface涂漆了的表面Coated with a metallic base waterproof lubricant to prevent galling in use and aqueous corrosion during testing漆上金属防水润滑剂以防止卡滞及在试验过程中出现的水腐蚀Coatings涂层plating电镀Code for construction and acceptance of spherical tanks球形储罐施工和验收规范GB50094 Code number代码Code symbol规范符号Coiler蛇管，盘管Cold bent冷弯Cold differential test pressure冷差试验压力Cold flash drum feed cooler冷闪蒸筒进料冷却器Cold-drawn bars冷拔棒Collapsing pressure垮塌压力Collar boltColor coding色码Column立柱Column塔器Combination of different material不同材料组合Combination units组合容器Combined with pneumatic与气压试验混合Combine-unit组合件Combustible distillates可燃液体Commodity specification 设备规格书Communicating chambers连通室Complete chemical analysis of the overlay完整的堆焊层化学分析Complete fusion and complete joint penetration完全熔合及完全焊透Composite组合件Compresed asbestos gaskets压紧的石棉垫Compressed air service压缩空气锅炉Compression type压环式Compressors压缩机Computation 计算Computed working pressure from hydrostatic test由水压试验计算的工作压力Computer control module计算机控制模数Concave and convex凹面和凸面Concavity凹陷Concentric reducer sections同心变径段Concentric ring wave form disk plate同心环碟片填料Concert with inner surface与内表面吻合Conditioned areas修整区域Cone锥体Conical head锥形封头Conical reducer sections锥形变径段Conical sections圆锥截面Connection size standard连接尺寸标准Conspicuous location显眼的位臵Constant volume process zone定容过程区Construction fixtures建造夹具Construction结构数据Consumable and non-consumable electrode process熔化电极法与不熔化电极法Consumable inserts焊接用可熔化嵌条Contact facing接触面Contact pyrometers接触高温表Contamination污染物recontamination再污染Continuation of shell optional壳体可延伸Continuous full penetration weld连续全焊透焊逢Continuous heat resistance持续耐热Control of stamping打印管理Controlled shot peening控制喷丸Conversion换算Coolant冷却剂Cooling chamber冷却室Cooling rate降温速度Cooling tower fan冷却塔风机Cooling way and time 冷却方式与时间Copper sulfate etching硫酸铜Corner and fillet圆角和倒角Corner joint角接头Corner or tee joints角接或T型接头Corner, fillet角接焊缝，角焊缝Corrected for temperature温度校正Corrections for moisture content of the steam校正蒸汽的含水量Corroded thickness蚀态厚度Corrosion resistant linings防腐蚀忖里Corrosion resistant weld metal overlay cladding抗腐蚀堆焊金属层Corrugated metal, asbestos inserted, or corrugated metal, jacketed asbestos filled内填石棉的波纹状金属或充填夹层石棉的波纹金属Corrugated plate波形板Corrugated shells波纹形壳体Corrugating paper machinery波纹板机械Corrugating paper machinery瓦楞纸机械Cosmetic grinding休整性打磨Counter-current逆流/回流Coupling threadCouplings plugged to prevent damage塞紧以防损坏Coupling管箍/耦合/联结Cover flange外头盖法兰Cover plates/Cover盖板Cracks裂纹seams皱纹laps折叠cold shuts冷隔lamination分层Cradle吊架Crater crack火口裂纹Crimping强压Critical temperature临界温度Cross stray斜撑Curvature of the vessel wall容器壁的弧度，Curvature曲率Cutting oil切削油scale residues剥落的残渣Cutting切割fitting装配and alignment对准CVN impact testing夏比缺口冲击试验Cyclic operation循环工作Cyclical loading循环载荷Cylinder筒体Cylindrical shell 柱状壳体，Cylindrical圆柱形Damp潮湿greasy油污oxidized氧化Dead load静载荷Defective brazing有缺陷的钎焊Defect缺陷Defined limit规定的范围Deflecting baffle导流板Deflection cause linkage挠曲引起泄露Deflector导流装臵Delayed cracking延迟裂纹Demister破沫器Demonstration of density and penetrameter image射线透照的黑度和透度计Dengsity密度Velocity流速pressure drop压降viscosity粘性molecular weight分子量Density密度Deoxaluminite weld-through primer焊接坡口防护涂料Deoxidation脱氧Depentanizer feed-bottoms exchanger脱戊烷塔进料/塔底换热器Deposited weld metal熔焊金属Depth of offset折边深度Derusting去锈Design and construction of large, welded, low pressure storage tanks大型焊接低压贮罐设计和制造API620Design duty设计功率Design for full vacuum@ temper.Design life设计寿命Design margin设计裕度Design or type number of valve阀门设计号或型号Design parameter设计参数Designation名称Detachable chamber独立可分的受压室Detect pressure观察压力Detect surface calibration notches 检测表面标定缺口Detrimental corrosion有害的腐蚀Detrimental discoloration有害变色Deviation背离，（对角线、角度上的）偏差DEW=dew point露点Diagonal white and yellow bands 白黄色斜纹Dial indicating pressure gages表盘指示压力表Diameter exemption直径的豁免Diaphragm type pressure relief valve隔膜式泄压阀Die-stamping for material identification打材料标志硬印Diff. Pressure/ Differential pressure压差Differ in thickness厚度差Diffusible hydrogen limit扩散氢限制Digital reading pressure gages数字压力表Dimensionless factor无量纲系数Dimpled压凹窝的, embossed使凸出Direct firing(DF)直接火容器Discharge of safety valves安全阀泄放Discharge pipe排放管Discharge出料Dished cover球面凸形封头Dished heads碟形Disk-doughnut baffle盘-环行折流板Dismantling拆除installation 安装Displacement measurement test位移测量试验Dissimilar metal welding异种金属焊接Dissimilar weld metal不同金属的焊接Distortion大变形Distribution devices配电装臵Distribution, retention发送，保存Distributor分布器Double curvature双曲率single curvature单曲率Double pipe套管Double weld双道焊Double-jacketed金属包垫片Double-welding双面焊Doubly curved shell两个曲面组成的壳体Dowel 销子Drain opening排尽孔Drainage排放Drilled or bored holes钻孔或镗孔Drips and runs in the path of the weld joint焊道内的防护涂料滴痕或流痕Driving fit打入配合（封头与壳体焊接前）Drop weight test落锤试验Drum圆桶Dry saturated steam干饱和蒸汽Dry weight of total halogen or sulfur or in-organic halogens总卤素或硫或无机卤素干重Ductile cast iron可锻铸铁Due to fatigue or creep由于疲劳或蠕变Dummy tubes O.D.堵管平盖Duplex stainless steel双相不锈钢Duplicate and similar parts相同件和相似件During fabrication/Fitting up制造过程中制造期间Dye penetrant examination of the completed weld 100%的着色渗透探伤Dye stenciling染色镂刻Dye-penetration detection着色探伤Dynamic loading动载荷Each bundle每捆, each lift每个吊运包装, shipping container集装箱Each side of each circumferential welded intersection每一环向接头相交的两侧Earth lug接地板Earth lug接地板anchor bolt地脚螺栓lifting lugs吊耳Eccentricity of shell壳体的偏心度Eddy current test涡流探伤with eddy current methodEdge defects边缘缺陷Edge of plates, metal removal from由加工板边去除金属Effective gasket width有效垫片宽度Effective temp. Difference有效温差Effective thickness of conical section锥形段的等效厚度Efficiency系数Elastic buckling stress弹性失稳应力Elasticity, modulus of弹性模量Elastomer合成橡胶Elbow弯头Electrode core焊芯Electrode rods电焊条electrode wires电焊丝Electrode焊条Elevation above ground拔高/地面高度Ellipsoidal椭圆形, torispherical碟形, hemispherical半球形, conical锥形Ellipsoidal椭圆形hemispherical半球形spherically dished(torispherical)球面凸形（碟形）conical 锥形tori-conical(cone head with knuckle)折边锥形（具有转角区的锥形封头）Elliptical projection technique椭圆发射技术Elongated indication条型显示Embody包含，体现Embrittlement 脆化Employing straight threads使用直螺纹Enameled vessel搪瓷容器Enamel瓷釉Endurance limit疲劳极限Engineering drawings工程设计图纸commodity specification商品规格书Engraving or hard stamping蚀刻或打钢印Enlarged inlet nozzlesEnthalpy-temperature profile: linear热函-温度曲线图：线性的Entirely in spherical portion全部在球体部分Epoxy环氧涂层Equally spaced on two rows均匀分布为两排Equipment setup, calibration, operation, evaluation of examination设备调试、校准、操作、和检测数据评定Equip-spaced mid-span跨中均布Erection weight安装重量Erosion冲蚀Establish a mean analysis确定化学成分平均值Etchant浸蚀剂Etching, of sectioned specimens侵蚀，关于截面试样Evaluation and retests评片与复验Evaporator蒸发器Examination of sectioned specimens剖面试样的检验Examination report（超声波）探伤报告Locate indication area确定指示区域echo height回波高度indication dimensions指示尺寸depth below the surface表面下的深度type of indication指示类型Examined by审核人Excess stock from… material余料Excessive deformation过大的变形Excessive scoring of the plates平板上的深痕Exothermic kits放热包Expanded connection胀接Expansion joint膨胀节Explosion-proof group防爆等级Explosive welding of multiplayer tubes多层管爆炸焊Exposed inside edges内侧裸露出的边缘Exposed left un-welded留下不予焊接的显露部分Extend over…延伸到…Extended heat transfer surfaces延伸的转热面Extended or thickened necks加长或加厚管颈。