中国现代诗歌精选head-end processing to be connected into a thread. With hood protection: using special steel wire protective cap to protect the steel wire to prevent screw thread bump or contaminated with dirt. Classification code according to the specifications and type (2), connector connector steel steel wire under the screw head caps inplace ? ? joints tighten ? mark ? intented for operation steel in place: carry the yarn inspection of steel bars to stay connected. Connector tighten: with a wrench and pipe wrench tighten the connector. Mark: Mark already screwed joints, apart from not tighten the joints of steel bar connection diagram: 2, steel connection in steel connections, steel specifications should be consistent with connection sleevespecifications and ensure yarn and threads clean and intact within the connecting sleeve. Alignment axis when connecting reinforcement thesteel twisted into the corresponding connection socket. Joint splicingis complete, two head pushing each other in the sleeve of the central location, sleeve at each end Ruth clasp 1~2 clasp, extended number of exposed threaded joints without restrictions, but there are clearly marked, to check whether the enter sleeve length to meet the requirements. Reinforced joints applied after tightening torque tightening torque wrench by not less than the table value check Check, and mark. Joint of rolling straight threads rebar diameter tighteningtorque values/mm ? 18~20 ? 22~25 ? 28~32/tightening torque values (N • m) 160 230 300 Note: when different diameter rebar十首最值得阅读的现代诗:一、第十首，余光中的《等你, 在雨中》:等你, 在雨中, 在造虹的雨中蝉声沉落, 蛙声升起一池的红莲如红焰, 在雨中你来不来都一样, 竟感觉每朵莲都像你尤其隔着黄昏, 隔着这样的细雨永恒, 刹那, 刹那, 永恒等你, 在时间之外在时间之内, 等你, 在刹那, 在永恒如果你的手在我的手里, 此刻 head-end processing to be connected intoa thread. With hood protection: using special steel wire protective cap to protect the steel wire to prevent screw thread bump or contaminated with dirt. Classification code according to the specifications and type (2), connector connector steel steel wire under the screw head caps in place ? ? joints tighten ? mark ? intented for operation steel in place: carry the yarn inspection of steel bars to stay connected. Connector tighten: with a wrench and pipe wrench tighten the connector. Mark: Mark already screwed joints, apart from not tighten the joints of steel bar connection diagram: 2, steel connection in steel connections, steel specifications should be consistent with connection sleevespecifications and ensure yarn and threads clean and intact within the connecting sleeve. Alignment axis when connecting reinforcement thesteel twisted into the corresponding connection socket. Joint splicingis complete, two head pushing each other in the sleeve of the central location, sleeve at each end Ruth clasp 1~2 clasp, extended number of exposed threaded joints without restrictions, but there are clearly marked, to check whether the enter sleeve length to meet the requirements. Reinforced joints applied after tightening torquetightening torque wrench by not less than the table value check Check, and mark. Joint of rolling straight threads rebar diameter tightening torque values/mm ? 18~20 ? 22~25 ? 28~32/tightening torque values (N • m) 160 230 300 Note: when different diameter rebar如果你的清芬在我的鼻孔, 我会说, 小情人诺, 这只手应该采莲, 在吴宫这只手应该摇一柄桂浆, 在木兰舟中一颗星悬在科学馆的飞檐耳坠子一般的悬着瑞士表说都七点了忽然你走来步雨后的红莲, 翩翩, 你走来像一首小令从一则爱情的典故里你走来从姜白石的词里, 有韵地, 你走来看过好多关于这首诗的评论，印象最深的是一篇关于科学馆和瑞士表那阕如何精彩的head-end processing to be connected into a thread. With hood protection: using special steel wire protective cap to protect the steel wire to prevent screw thread bump or contaminated with dirt.Classification code according to the specifications and type (2), connector connector steel steel wire under the screw head caps inplace ? ? joints tighten ? mark ? intented for operation steel in place: carry the yarn inspection of steel bars to stay connected. Connector tighten: with a wrench and pipe wrench tighten the connector. Mark: Mark already screwed joints, apart from not tighten the joints of steel bar connection diagram: 2, steel connection in steel connections, steel specifications should be consistent with connection sleevespecifications and ensure yarn and threads clean and intact within the connecting sleeve. Alignment axis when connecting reinforcement thesteel twisted into the corresponding connection socket. Joint splicingis complete, two head pushing each other in the sleeve of the central location, sleeve at each end Ruth clasp 1~2 clasp, extended number of exposed threaded joints without restrictions, but there are clearly marked, to check whether the enter sleeve length to meet the requirements. Reinforced joints applied after tightening torquetightening torque wrench by not less than the table value check Check, and mark. Joint of rolling straight threads rebar diameter tightening torque values/mm ? 18~20 ? 22~25 ? 28~32/tightening torque values (N • m) 160 230 300 Note: when different diameter rebar文字，说是古典与现代结合云云，不过，个人认为，这两个意象的出现也许就是这首诗唯一的败笔，西装和瓜皮帽的搭配让人看着怎么也不舒服。