1、电源：单相AC110-220V，0.75-1KW，50/60HZ2、空气压力：0.4-0.6MP3、尺寸：300*290*370mm4、重量：32Kg全体构成图1、插上电源，插上气管2、打开总电源开头，各电气部件通电正常，整机进入待机状态。
3、打开气源开关，把气压送进机，调侧过滤器，拉起圆钮，旋转调至压力5Kg，数字气压表有显示，旋动精密调压阀使气压表为所需值（例如：350=0.35MP=3.5Kgf=3.5个大气压力）4、触摸屏显示：如（图一）5、轻触显示屏开机按钮，如（图2）平台气缸推出，设备自动进入无泡工作待机状态，如（图2）一、规格∨二、机器全体构成及说明∨三、操作说明∨6、此时将待压屏放在托盘上，按启动开关开始进入自动无泡工作模式，如（图3）：无泡模式贴合一次工作产品全过程可在3-5分钟的时间完成，时间可调高效模式贴合一次工作产品全过程可在20-50秒钟的时间完成，时间可调7、若需要修改贴合参数可点触键盘输入设置密码（9988）即可显示和修改相关参数（规定了设定围）如（图4）：8、若要切换高效贴合模式，可返回到第2步点触高效模式。
9、自动运行中紧急情况下按急停键，设备将进入待机状态，请注意托盘进出，以免夹伤。
10、贴合过程中，如果要提前出仓，点击出仓键即可。
11、按电源键关机，托盘自动关闭后再关闭进气阀。
12、温度设置：按一下SET键，再按上、下键，调至所需温度，设置完成。
1、气压总是调不大，请检查空压机本身的气压是否过低。
2、触摸屏通信不良，请检查显示屏与PLC的连接电缆两端的连接头是否松动。
3、开机后仓门不会自动打开，请注意数字压力表，压力要在显示200以上，右侧指针压力表要在4（Kg）-6（Kg）之间。
4、机器不通电，请检查保险丝（15A）是否熔断并更换。
5、贴合机工作过程中，忽然关机后再开机，仓门不会自动开，是因为仓保持着真空，此时按一下出仓键或急停键后，右旋弹出即可开仓门。
6、开机后显示无泡模式和高效模式，如没有选择某模式自动进入无泡模式。
7、无泡模式：贴合时间在3分钟-5分钟可调。
高效模式：贴合时间在10秒-30秒可调。
8、仓门动作的快慢与压力相关。
9、真空泵的电源线一定要插在贴合机上。
10、贴合进程中：真空泵一直工作长时间仓门不开，是因为真空度达不到（设定为-98°），请检查真空泵到贴合机的连接气管两头是否锁紧，真空泵镜面是否有一半以上高的油面。
11、如果产品掉入仓，请不要关机，先把进气阀关闭（空压机上），按下急停键后关机，用其他工具取出，急停键右旋弹出正常开机，打开气阀后正常使用。
12、如果显示屏后面有IC的产品，利用备用硅胶片相对位置开孔，放入托盘保证产品平整，预防爆屏。
13、如果产品气泡比较多，请注意负压，设定是否在（-98以上），正压力可相对调高。
14、开机后，只听到气流声，仓门不出来。
急停键已被压下，把急停键向右转一下，弹出即可。
1.Power supply:single-phase AC220V/2Kw，50/60hz2.Air pressure:0.1-0.6MP3.Size:300*290*370mm4.Weight:32gkAll the composition figure1.Plug in,plug in the trachea2.Open the total power switch,electrical components electricity is normal,The machine into standby mode3.Open the air switch,send air pressure into the machine,digital barometer has shown,gyration precision pressure regulating valve pressure screen required is a barometer of the value (for example :350=0.35MP=3.5kgf=3.5 atmospheric pressure)4.Touch screen display:(AS shown in figure 1)5.Touch screen button to boot,launch platform cylinder,devices to work automatically entered into without bubble standby,(As shown in figure 2):6.Will stay at this time the pressure screen on the tray,press start switch to start into the automatic without bubble working mode,(As shown in figure 3):No bubble model fit a work products can be in 3 to 5minutes to finish the whole process,time is adjustable.Efficient mode of joint is a whole process work products can be finished in a 20 to 50 seconds,time is adjustable.7.lf need to modify the joint parameters can press set button to enter modify images are,(As shown in figure 4):Bytapping the keyboard input password (9988)can display and modify the relevant parameters(rules set the range),8.To switch efficient joint mode,can return to the step 2 by tapping the efficient mode.9.Run automatically in case of can emergency stop button,the device will enter standby mode,please pay attention to the tray in and out ,lest the task.mination process,if you want to advance out of the warehouse,click the warehouse button11.Press power key to turn it off,the tray automatically shut down after turn off the gas source.12.Temperature setting:press the SET key,then press up,down ,to the required temperature, SET up complete1.Pressure always tune is not big, please check whether the pressure of the air compressor itself is too low.2.Touch screen,poor communication,please check the screen and PLC at the ends of the connecting cable connector is loose.3.After startup storehouse door will not open automatically,please note that the digital pressure gauge on the right side (kg)in4-6(kg).4.Without power to the machine,please check if the fuse(15a)fuse and replace.5.In the process of the joint work,suddenly turned off again after boot,storehouse door does not automatically open,because the interior of the warehouse in the vacuum,at this time click theCangJian or abrupt stop button,dextral popup can open the door.6.After startup display without bubble model and efficient,if not choose a mode is automatically entered into without bubble.7.No bubble mode:joint time adjustable in 3 to 5 minutes.8.Movement speed of the doors is associated with stress.9.Vacuum pump power cord must be inserted in the laminating machine.minating process:vacuum pump has been working for a long time storehouse door does not open ,because the vacuum degree of not toset the(as-98°)，check the vacuum pump to the laminating machine connection tracheal whether two head lock,mirror to see if there is more than half of the high vacuum pump oil level.11.If the products fall within the transport ,please don′turn it off and take the inlet valve closing(air compressor machine),press the stop button to turn it off. After using other tools, abrupt stop button right popup normal boot,open the valve after normal use.12.If you have any IC products,behind the screen using the alternate silicon sheet relative position opening, put kindergarten plate of flat products, explosion prevention.13.If the product bubble is more,please pay attention to the negative pressure,whether set in more than(98),the positive pressure may be relatively higher.14.After startup,only hear the air warehouse door not to come out, Under the urgent stop button has been pressed, the stop button to the right, and the pop-up.。