三层交换机switch配置：
☐Router(config)#hostname switch-L3 //对路由器重新命名
☐switch-L3 (config)#interface Fastethenet0/1 进入F0/0口的配置模式
☐switch-L3(config-i f)#ip address 192.168.1.1255.255.255.252 //给F0/0口固定IP
☐switch-L3(config-if)#no shutdown
☐switch-L3(config-if) #exit //退出F0/0配置模式
☐switch-L3 (config)#vlan 10 //进入vlan 10dua10端口配置模式
☐switch-L3(config-if) #interface vlan 10
☐switch-L3(config-if)#ip address 172.16.1.1255.255.255.0 //给S0/2固定I P
☐switch-L3(config-if)#no shutdown
☐switch-L3(config-if) #exit
☐switch-L3(config) # interface Fastethenet0/2
☐switch-L3(config-if) #switch access vlan 10
☐switch-L3(config-if)#no shutdown
☐Router-1702(config-s0/2)#exit
(2)路由器router-a的基本配置
Router#configure termina l
Router（config）#hostname router-a
Router（config）# interface Fastethenet0/1
Router（config-if）# ip address 192.168.1.1 255.255.255.252
Router（config-if）# no shutdown
Router（config-if）#exit
Router（config）# interface Fastethenet0/1
Router（config-if）# ip address 192.168.1.1 255.255.255.252
Router（config-if）# no shutdown
Router（config-if）#exit
(2)路由器router-b的基本配置
Router#configure termina l
Router（config）#hostname router-b
Router（config）# interface Fastethenet0/0
Router（config-if）# ip address 192.168.0.2 255.255.255.252
Router（config-if）# no shutdown
Router（config-if）#exit
Router（config）# interface Fastethenet0/1
Router（config-if）# ip address 10.10.1.1 255.255.255.0
Router（config-if）# no shutdown
Router（config-if）#exit
(4)在三层交换机switch-L3上配置RIP路由协议
switch-L3 (config)#ip routing
switch-L3 (config)#router rip
switch-L3 (config-router)#network 192.168.1.0
switch-L3 (config-router)#network 172.16.1.0
switch-L3 (config-router)#version 2(设置rip路由协议的版本为rip v2) switch-L3 (config-router)#end
switch-L3 #write m emory
(5)在三层交换机switch-A上配置RIP路由协议
switch-L3 (config)#rou ter rip
switch-L3 (config-rout er)#network 192.168.0.0
switch-L3 (config-router)#network 192.168.1.0
switch-L3 (config-router)#version 2(设置rip路由协议的版本为rip v2) switch-L3 (config-router)#end
switch-L3 #write m emory
(5)在三层交换机switch-B上配置RIP路由协议
switch-L3 (config)#rou ter rip
switch-L3 (config-rout er)#network 192.168.0.0
switch-L3 (config-router)#network 10.10.1.0
switch-L3 (config-router)#version 2(设置rip路由协议的版本为rip v2) switch-L3 (config-router)#end
switch-L3 #write m emory