当前位置:文档之家› 铸造专业英语

铸造专业英语

铸造厂,铸造foundry铸造尺shrink rule铸造尺shrinkage rule铸造尺shrinkage scale铸造从业员foundry man铸造法casting process铸造方案founding method铸造方案plan of casting铸造废料foundry scrap铸造机casting machine铸造计划casting plan铸造设计,铸件设计casting design铸造性试验castability test铸造应变casting strains铸造用钉foundry nails铸造用生铁foundry pig iron铸造状态as-cast condition,as-cast铸造组织cast structure铸造作业casting manipulations铸芝模ingot mold铸芝偏析ingotism抓斗绞车装置grabbing gear专业铸造工场production foundry砖brick转变用铁水(调配成分) transition iron 转动炉,转筒炉rotary furnace转换conversion转炉converter转炉钢converter steel转炉炉榇converter lining转盘混砂机rotating pan mill转速revolving speed转台,转盘rotary table转台喷粒机shot tablast转位半径transititon radius转运车transfer trolley转运翻箱装置transfer-turnover device 转运盖c装置transfer-closing device 转运装置transfer device装砂心coring up装载机bucket loader装载能量loading capacity追补焦split coke锥形炉腹bosh坠裂试验shatter test坠落试验drop test坠重试验drop-weight test自动电极控制automatic electrode control自动电流调整器automatic current regulator自动化automation自动化系统automatic system自动加料设备automatic charging equipment自动进给automatic feeding自动控制automatic control自动配料机automatic doser自动燃烧控制automatic combustion control自动送料(压铸) automatic ladling,die casting自动温度控制器automatic temperature controller自动造模工场automatic molding plant自动铸砂处理设备automatic sand plant自动转盘式造模机automatic turntable molding machine 自来水tap water自然腐蚀试验field test自然裂缝seasoning shake自然破裂season cracking自然干燥法(木材),自然季化处理(铸件) natural seasoning 自然时效natural aging自然通风natural draft自行除渣self-skimming自行除渣风口self-slagging tuyere自行结晶idiomorphic crystal自行退火self-annealing自硬钢self-hardening steel自硬性self-hardening自硬性造模法no-bake process自硬性粘结剂self-curing binder自由度degree of freedom自由水free water纵向裂痕longitudinal crack足尺full size阻挠元素interfering element阻销stop pin组成图constitutional diagram组成物component组成楔值constitutional wedge value组合built up组合构造composite construction组合模板built-up plate组合模型built-up pattern组合模型composite pattern组合模型pattern assembly组合砂箱built-up molding box组合砂心盒multiple core box组织,级成constitution组织成分constituent组织瑕疵structure defects钻悄(试样用) drillings钻维硬度值(韦克氏硬度) diamond pyramid hardness number,Vickers hardness 最大负载maximum load最后加工finish最适水分(模砂) optimum temper moisture作业可靠性operational reliability作业砂(生产线) production sand作业准备日程operational scheduling直立浇铸vertical pouring直立心型端承,直立砂心头vertical coreprint直立旋板心轴upright spindle直立造模vertical molding直立造模法mold on end直立铸模vertical mold直立铸造vertical casting直落砂心drop core直木纹edge grain直提砂心头tail print直通干燥炉through feed drying furnace直显照片(金相) direct print直压式合机direct pressure closing植物油vegetable oil指形进模口finger gate酯系硬化法ester-process制震能damping capacity蛭石vermiculite置冲法pour-over method置冲法transfer method置模箱set-off box滞流(铸疵) mistrun制程退火process annealing制模型铣床pattern milling machine制图,起模drawing制造熔接production welding制造冶金学process metallurgy质量效应,厚薄效应mass effect致密度consistency中间处理intermediate treatment中间检查intermediate inspection中间金属intermediate metal中间砂箱,中间模箱cheek box ,cheek flask中间砂箱,中间模箱raising middle flask中磷生铁(P0.4-0.75%) medium phosphorus pig iron 中模,中间砂箱,中间模箱cheek中碳钢medium carbon steel中途添焦spreader charge of coke中线收缩centerline shrinkage中心板,旋刮板心轴承座center plate中心规centergage中性耐火材料neutral refractory materials中性熔渣neutral slag中性砖neutral brick中周波感应电炉intermediate frequency furnace 锺,锺形塞进器bell锺青铜bell bronze重搭overlap重捣砂hard ramming重金属铸件heavy-metal castings重晶石heavy spar重力分离器gravitational separator重力滚子输送机(倾斜式) gravity roller conveyor重力偏析gravity segregation重力输送机gravity conveyor重力压铸法gravity die casting重力铸造法gravity casting重燃油heavy fuel oil重熔remelting重熔工场secondary smelter重印法(造模) print back重油heavy oil重整石英砂replenishment quartz sand重铸recasting轴shaft轴承合金bearing metal皱痕面(铸疵) creasy surface皱皮(铸疵) orange peel皱皮(铸疵) surface folding珠,粒,击,射注过程(压铸) shot珠击处理shot peening珠击机shot peening machine珠粒喷击清理shot blasting珠泡bead竹叶状液面花纹bamboo leaves pattern主成分,基本金属primary coil主模master mold主心型,主砂心body core煮材干燥法boiling seasoning助流剂fluidizer助黏剂,膨胀性粘结剂swelling binder注入槽(压铸) pouring shot注射器injector柱column柱pillar柱塞,塞罩plunger柱塞,塞罩post柱状结晶columnar crystal柱状组织columnar structurew仓壁冲击振动器impact vibration on bin wall 贮砂桶匣(砂心机用) magazine铸包camlachie cramp铸壁wall铸壁鹌鹑wall thickness铸补burning on铸补tinkering铸成率casting yield铸成试片cast-to-shape specimen铸尺contraction rule<BR>铸疵casting defect铸疵defect test铸疵,铸造缺陷foundry defects铸疵试验defect test铸锭ingot铸锭底砖spider铸锭浇口砖king brick铸锭模ingot case铸锭状态as-ingot铸钢cast steel铸钢造模料steel foundry molding compound 铸工caster铸工founder铸合金ferro-alloy铸弧pouring arc铸件castings铸件表面casting surface铸件表皮casting skin铸件飞边,铸件毛边casting fin铸件内包物cast-in insert铸件清理,最后加工finishing铸件清理图dressing shop铸件修整finishing of castings铸件应力casting stress铸焦foundry coke铸坑casting pit铸坑foundry pit铸裂(铸疵) casting crack铸瘤rising铸漏bleed铸漏break out铸漏run-out铸漏件bleeder铸模mold,mould铸模布置mold layout铸模除除掉(压铸) impression block铸模龟裂,脉状痕(铸疵) veining铸模夹具mold clamp铸模输送机mold conveyer铸模块合mold assembly铸耙rake铸皮skin铸皮孔skin holes铸砂casting sand铸砂处理foundry sand preparation铸砂处理preparation of sand铸砂处理工场foundry sand preparation plant 铸砂控制sand control铸砂控制设备sand control equipment铸砂流动性flowability of sand铸砂流动性foundry sand铸砂膨(铸疵) sand drier铸砂强度试验strength test of sand铸砂强化strengthen the sand铸砂烧结(铸疵) sand burning铸砂烧贴(铸疵) sintering point铸砂油casting iol铸生铁机pig machine铸损foundry losses铸损,不良铸件waster,foundry losses铸铁cast iron铸铁工场iron foundry铸铁管cast iron pipe铸铁组织图cast iron diagram铸铁组织图structural diagram of cast iron 铸造founding铸造,铸件casting铸造场smith shop圆盘砂轮机disc grinder圆套筒round bush圆条测温法bar test圆筒式炉(回转炉) drum type furance圆筒形浇桶drum ladle圆头镘刀roound nose圆形砂rounded grain圆形砂粒rounded sand云母粉mica flour云母粉mica powder运轮,台车carriage运送箱tote box运原性蒙气reducing atmosphere运原状态reducing condition杂质impurities再炽,再辉recalescence再炽点,再辉点recalescent point再处理erpreparation再处理砂reconditioned sand再负载reloading再结晶recrystallization再结晶温度recrystallization temperature 再冷却系统recooling system再黏接砂rebonded sand再热炉reheating furnace再生砂reclamation sand再生铁remelted pig iron再生铁synthetic pig iron暂垫造模法mold on an oddside凿锤chipping hammer凿刀chipping chisel凿磨浇口shagging凿平chipping凿平问chipping room凿子,凿机chipper凿子,凿机chisel造模molding造模板mold board造模板molding board造模板molding plate造模板ramming plate造模材料molding materials造模材料添加剂molding material additive造模粗砂molding gravel造模地坑molding pit造模钉molding brad(pin)造模法molding method造模工具molder's tools模工作台molder's bench造模工作台molding bench造模机molding machine造模袷度molding allowance造模区molding bay造模设备molding apparatus造模性moldability造渣剂slag forming constituent造渣期slag forming period造渣石灰slag lime造渣作业slag practice增碳carbon pick-up增碳recarburization增碳剂recarburizer增碳剂recarburizing agent增碳焦recarburization coke增压冒口,威廉氏冒口atmospheric feeder(atmsopheric riser,William's riser) 增压冒口,威廉氏冒口William's riser,atmospheric riser增压砂心cracker core增压砂心pencil core增压砂心penetration core增压砂心,嵌入砂心insert core增压砂心,威廉氏砂心atmospheric core,William's core渣dirt渣比,碱度slag ratio渣阱dirt trap渣孔(铸疵) slag blowhole渣棉slag wool渣壳slag crust渣桶slag ladle渣位高slag level渣窝slag pocket轧辊,辊子roll轧屑roll[ing] scale闸喉,闸口choke闸喉式流道choked runner system闸喉作用choking粘土质耐火砖fire clay brick展性,可锻性malleability展性处理malleablising展性热处理铁矿malleable ore展性退火malleablising annealing展性铸铁(可锻铸铁) malleable cast iron展性铸铁(可锻铸铁) malleable iron展性铸铁用生铁malleable pig iron辗制硅砂artifical silica sand章鱼状石墨octopus graphite胀疤expansion scab胀模(铸疵) swell胀陷,上模剥砂(铸疵) pull down罩式炉lifting furnace遮蔽电弧熔接shielded-arc welding遮热板heat shield折旧amortization折旧depreciation折缘(黑心展性铸铁) picture frame锗(Ge) germanium真空除氧法vacuum degassing process真空精炼vacuum refining真空熔解vacuum melting真空造模法,V造模法V-process,vacuum-secaled process 真空铸造vacuum casting真离心铸造法true centrifugal casting砧anvil砧台式震实造模机anvil-jolter针对铸铁acicular cast iron针孔(铸疵),销孔pin-hole针状组织acicular structure针状组织铸铁bainite cast iron振动vibration振动捣砂vibration ramming振动分配器vibrating distributor振动器vibrator振动清箱mechanical knockout by vibration振动清箱,振动清砂处shake-out振动清箱机molding box shake-out device振动清箱机,振动清砂机shake-out machine振动清箱性能shake-out property振动清箱栅shake-out grid振动清箱栅shake-out screen振动筛jigging screen振动筛shaking screen振动筛vibrating sieve震捣jolt ramming震动jolt震动板jolting plate震动废黜模板造模机jolt molding machine with turnover plate震动机jarring machine震动清箱吊架jointing hanger震动压挤拔模造模机jolt squeeze stripper molding machine震动压挤造模机jolt squeeze moldng machine震动造模机jolt molding machine震动造模机jolter震箱清砂机flask shanker蒸馏器retort蒸馏碳retort carbon蒸气脱蜡autoclave dewaxing整流器rectifier整体模型solid pattern整体模型铸模solid pattern mold整温控制thermostat整缘trimming整缘模具trimming dies整缘压机trimming press正常化normalizing正常偏析normal segregation正常温度normal temperature正常折曲试验normal bend test支架(压铸),垫块packing block支台,置模台set-off bench支柱(熔铸炉) prop枝形进模口bracnch gate直尺staight edge直接电弧炉direct arc furnace直接浇口drop gate直接浇铸direct pouring直接浇铸法direct casting直接进模口direct gate直接进模口slot gate直接气压式热室压铸机(压缩空气直接压于熔液) direct pressure hot chamber machine 氧化硅基砂silica base sand氧化性蒙气oxidizing atomosphere氧化性溶解oxidizing melting氧皮铝alumite氧焰割oxycut氧乙炔熔接,气焊oxyacetylene welding样板,刮板,量具template,templet样规sizing peg摇动炉rocking furnace摇斗炉shaking lade摇台cradle窑炉kilnb 趸 ?anti-oxidant冶金焦metallurgical coke冶金术metal technology冶金学metallurgy液化liquefaction液面花纹break surface pattern液面花纹figure液面花纹play figure液态收缩liquid contraction液态收缩liquid shrinkage液体压力计manometer液相曲线liquidus curve液相线liquidus [line]液相线liquidus line液压气动砂箱升提机构hydropneumatic flasklifting mechanism 液压千斤顶hydraulic jack液压清砂铸件设备hydraulic cleaning equipment液压试验hydraulic pressure test叶轮式喷砂机turbine sand blaster一氧化碳carbon monoxide一氧化铁(FeO) iron protoxide铱(Ir) iridium移动吊车mobile crane移动皮带升降机mobile belt elevator移动式烘炉portable drying oven移动式烘模机portable mold dryer移动式可倾前炉removable clay matter移动式摔砂造模机motive type sand slinger移入shunting-in移位装置shifting facilities移装(外砂心) draw back移装砂心inset core遗传性heredity乙二醇glycol乙炔acetylene乙炔发生器acetylene generator乙炔墨acetylene black(acetylene smoke)乙炔墨acetylene smoke,acetylene black乙炔熔接acetylene welding抑制剂inhibitor易开砂箱easy off slip flask易燃物inflammable易熔合金fusible alloy异形管件specials意外防止条例accident prevention regulations溢放口flow off溢放口pop off溢放口run-off溢放口strain relief溢放冒口run-off riser溢流over flow溢流道flow through溢流口hot spruing溢流口(压铸) over flow well音波试验sonic testing阴极锈法cathodic protection阴极氧化anodic oxidation铟(In)(稀金属元素) Indium银(Ag) silver银砂(无铁质硅砂) silver sand引导顶出(压铸) guided ejection英高镍(镍铬合金) Inconel英国国家标准B.S.(British Standard)英国铸铁研究协会BCIRA(British Cast Iron Research Associatin)英国铸造工程师学会IBF(Institute of British Foundrymen,London) 英制热单位(B.T.U.) British Thermal Unit应变,变形(铸疵) strain应变计strain gage应力stress应力腐蚀裂痕stress corrosion cracking应力集中stress concen应力破坏强度stress upture strength应力消除stress relief应力应变特性stress-strain characteristics应力应变图stresss-strain diagram樱木cherry tree荧光采伤法zyglo荧光渗透剂zyglo penetrant荧光fluorescence荧光镜fluoroscope荧光探伤法fluorescent crack detection荧光透视法(检查),荧光镜试验fluorspar 萤石(CaF2) fluorite萤石(CaF2) flushing硬点hard spot硬度hardness硬度计hardness tester硬焊brazing硬化(壳模) curing硬化,淬火hardening硬化合金hardening alloy硬化剂hardening agent硬化剂,硬化合金hardener硬化加速剂hardening accelerator硬化能,淬火性hardenability硬化深度hardness penetration硬化时间curing time硬结setting硬结砂用油setting oil硬木hardwood硬砂模型板hard sand match硬质焦炭,煤焦hard coke永久模,金属(铸)模permanent mold用瓢装液(压铸) ladling用销抬起pin lift优尼造模法Unicast process优先方位(结晶) preferred orientation油淬火oil quenching油粉浸渗试验(裂痕检出试验) oil-chalk test 油炉oil furnace油泥砂浆oil loam油漆,涂料paint油砂oil sand油砂模oil sand mold油砂心oil bounded core油砂心oil core油砂心oil sand core油污金属切屑swarf油烟,烟灰soot油硬化oil hardening油质黏结剂oil biner柚木teak游标卡尺vernier calipers铀U) uranium有机粘结剂organic binder有孔砂心撑perforated chaplet有麻口冷硬层chill zone with mottle有箱造模法flask molding有效高度burden height有效高度effective height有效黏土含量effective clay content 釉,光滑glaze鱼油fish oil鱼嘴栅fishmouth gate榆木elm余留铁水heel余铁深度(炉) pool depth余隙,间隙clearance余液(低周波炉) liquid core雨段退火two-stage annealing雨淋式环浇口pencil ring gate雨淋式进模口pencil gate雨淋式进模口pop gate雨淋式进模口shower gate浴池式氮化法bath nitriding预热preheating预热带preheating zone预热空气preheated air预热器preheater预熔金属pre-melt原料raw materials原料工业primary graphite,G-graphite 原料金属primary industy原料生铁base iron原模型granular pearlite原砂,原产硅砂crude sand原砂透气度base permeability原生组织primary structure原油crude oil圆板塞(浇池) disc plug圆底提砂钩Yankee's lifter圆规compasses圆粒round sleeker圆抹镘trowel星形裂缝star shake星形铁(滚光用) jackstar,mill star,star星形铁(滚光用) mill star,jack star,star星形铁(滚光用) star,jackstar,mill star星形铁(滚光用) tumbling stars形象因子shape factor型砖shaped brick修补removable tilting forehearth修毂抹刀boss spatula修角刀corner tool修角抹刀angle spatula锈rust锈皮,比例尺,秤scale锈皮,轧钢鳞片mill scale锈蚀度degree of rustin虚表比重apparent specific gravity虚表孔率apparent porosity虚表密度apparent density虚表容积apparent volume表温度apparent temperature虚筋,挡块(砂模) stop off蓄热炉regenerating furnace蓄热能量heat-retaining capacity蓄热器,再生器regenerator蓄热系统regenerative system续制铸件repeated use of sand旋臂吊车jib crane旋风集尘器cyclone dust collector(cyclon) 旋风净尘器cyclone scrubber dust collector 旋刮[砂] sweeping旋刮板sweep旋刮板sweeping board旋刮板臂sweep arm旋刮板马架sweeping molder's horse旋刮板模型sweeping pattern旋刮板模型sweeping template pattern旋刮板砂心swept core旋刮板心砂心spindle core旋刮板心轴,心轴spindle旋刮板轴心承座sweeping plate旋刮砂模sweeping mold旋刮砂心sweeping core旋涡补给口whirl-gate feeder旋涡混合机whirl mixer旋涡集渣包whirl-gate dirt trap旋沿试验法(流动性) spiral test旋转给料盘rotary feeding plate旋转刮板turning strickle旋转模板造模机truning plate molding machine旋转器swirl旋转干燥器rotary drier旋转砂心线setting line,core setting line旋转筛rotary screen旋转筛砂机rotary sand screen旋转式集尘器spin dust collection旋转台,转盘turn table旋转喂槽swivelling tundish旋转轧碎机rotary crusher悬吊砂suspended core悬吊砂轮机suspended grinder悬吊输送机trolley conveyor悬浮物suspended matter悬拱suspended arch悬挂式清箱装置pendant shaking equipment选别废料selected scrap雪明碳铁,雪明碳体cementite循环处理砂system sand循环砂recirculation system sand循环砂return sand压边整缘press trimming压痕试验indentation test压痕嚣,压痕物indentor压痕硬度试验机indentation hardness tester压坏(砂模),粉碎crush压挤板squeeze plate压挤板squezze boad压挤捣砂squeeze ramming压挤机squeeze machine压挤式顶杆造模机squeeze pinlift molding maching 压挤头(造模机) squeeze head压挤造模机squeeze molding machine压挤铸造squeeze casting压紧废料packeted scrap压块briquet,briquette压块bundle压块废料baled scrap压块机briquetting machine压力pressure压力计pressure gage压力室添加法pressure chamber method压力通风follow board压力铸造pressure casting压漏(铸疵) leakers压漏试验leakage test压模印coining压膜式壳模机diaphragm shell molding machine 压膜式造模机diaphragm molding machine压实性compactability压实指数compactability index压碎机crusher压缩机compressor压缩机die casting machine压缩空气compressed air压缩空气缸compressed air cylinder压缩空气喷吵机compressed air sand blaster压缩空气软管compressed air hose压缩性compressibility压重,砝码weights压重板(震动压面) jointing plate压铸,刚模铸造de cast压铸储井shot well压铸储筒shot sleeve压铸法,刚模铸造法die casting压铸件die castings压铸模dies压铸模涂料,刚模涂料die coating压铸模块die cast assembly亚共晶合金hypoeutectic alloy亚共析合金hypoeutectoid alloy亚甲蓝试验methylene亚硫酸监稠浆(黏结剂) sulphur,sulfur亚铝美尔Alumel氩(Ar) argon氩净化器argon purifier烟囱chimney烟囱chimney stack烟囱,炉胴(熔铁炉) stable-equilibrium diagram 烟囱罩hood烟道chimney flue烟道气flue gas烟火bank,the cupola烟煤bituminous coal烟煤soft coal烟气(有害的) fume烟雾smog延性ductility延性材料断口ductile fracture延性铸铁(球状石墨铸铁) ductile cast iron,nodular cast iron 研究工程师research engineer研磨纸emery paper焰割gas cutting洋铜nickel silver阳极处理anodizing阳极铜anode copper扬尘量dust emission杨氏模数,杨氏[纵弹性]系数Young's moldulus氧(O) oxygen氧丙烷焰割oxy-L.P.gas cutting氧化oxidation氧化oxidizing氧化表皮oxide skin氧化带zone of ozidation氧化精炼oxidizing refining氧化精炼refining by oxidation氧化期oxidizing period氧化气孔(铸疵) oxidized blowhole氧化损耗oxidation loss氧化铁iron oxide氧化物oxide氧化硅(SiO2) silica物理变化physical change物理试验physical test物理性质physical properties物理冶金physical metallurgy雾化atomization西拉高硅铸铁Silal吸热反应endothermic reaction吸入输送机suction conveyor吸湿性试验(高湿状态) high humidity storage test吸收absorption吸收剂absorbent吸收器absorber析出,沈淀precipitation析出热处理precipitation heat treatment析出退火precipitation annealing析出硬化precipitation hardening硅(Si) silicon硅肥粒铁silico ferrite硅肺病,石米沉着病silicosis硅分析仪,砂计silicon meter硅钢板silicon steel plate硅化钙calcium silicide硅化钙calcium silicon硅黄铜silicon brass硅块silicon briquets硅铝钙合金calicum-aluminium-silicon硅铝明(铝硅合金) silumin硅锰钙合金calcium-manganesesilicon硅凝胶,硅胶吸湿剂silica gel硅青铜silicon bronze硅青铜soilzin bronze硅砂silica sand硅砂捣料silica ramming compound硅砂粉silica flour硅砂浆涂料silica wash硅砂石砖ganister brick硅树脂,硅酮silicone硅树脂滑脂silicone grease硅酸silicic acid硅酸监silicate硅酸钠,水玻璃sodium silicate硅酸四乙酯tetraethl silicate硅酸乙脂ethyl silicate硅铁ferro-silicon硅铜silicon copper硅线石砖(高铝氧(70Al2O5)硅质耐火砖) silimanite brick 硅岩轮辗硅砂impeller-breaker sand硅藻土diatomaceous earth硅藻土infusorial earth硅藻土kieselguhr硅质粘土silicious clay硅砖silica brick硒(Se)(化学元素) selinium稀土金属rare earth metal锡(Sn) tin锡汗珠(铸疵) tin sweat锡青铜tin bronze习用潜变限度conventional creep limit洗尘器,涤气机scrubber洗净器scrubbing liquid细锉刀finishing file细孔组织cell structure细裂痕(铸疵) hair crack细裂纹(铸疵) caplillary crack细密波来铁fine pearlite细泥砂浆finishing loam细砂,河海丘砂bank sand细土粉,细泥fine silt煅烧calcine煅烧白云石calcine煅烧窑calcining kiln瑕疵flaw瑕疵大小flaw size瑕疵位置flaw location揬工场,揬造炉fore-hearth forge揬铁锈皮forge scale揬造,揬件forging下降速率lowering speed下浇道,坚浇道down gate下浇道,坚浇道down sprue下模bottom part下模nowel下模,下砂箱,下模箱drag下砂箱,下模箱drag box下砂箱,下模箱drag flask夏比冲击试验charpy impact test夏比冲击试验机Charpy impact test machine 夏比冲击值Charp impact value纤维状滑石fibrous talc显热sensible heat显微镜microscope显微镜试验microscopic inspection显微镜学microscopy显微镜照像photomicrograph显微偏析micro-segregation显微缩孔(铸疵) micro-shrinkage显微像micrograph显微组织micro-structure限缩变形hindered contraction限外显微镜ultramicroscope相phase相对频率relative frequency相对湿度relative humidity相对硬度relative hardness相律phase rule相平衡phase equillibrium相图phase diagram响铜bell metal象皮皱纹(铸疵) elephant skin橡胶浇道棒(造模) rubber down gate橡胶浇道棒(造模) rubber pouring funnel橡胶输送带rubber conveyer belt橡木oak消除冷硬退火chill removing annealing消除应力开沟,防裂槽stress relieving grooving 消泡剂antifoaming agent消石灰,熟石灰slake-lime消退fading消退时限fading time硝酸浸蚀液nital硝酸浸蚀液nitric acid销pin销合pin closure销紧力locking force销孔试验片keyhole specimen销抬造模机pin-lift molding machine萧氏精密造模法Shaw process萧氏硬度Shore hardness小块料cobbing小胚billet小铸件small castings校准calibration校准块calibration block校准钮calibrating knob楔wedge楔表进模口wedge gate楔塞作用wedge action楔形进模口wedge runner bar楔形试片wedge test piece楔形试验wedge test楔形销wedge pin楔形压力试验wedge penetration test楔形砖key brick楔形砖wedge brick楔值wedge value斜导杆(压铸) cam finger斜度砂箱,滑脱砂箱slip flask斜方晶系(结晶) rhombic system卸斗skip卸斗吊车skip hoist心,心型,砂心core心材heart wood心骨core bar心骨core grid心骨core iron心骨core rod心骨管core barrel心骨矫直器core rod straightner心骨模core grid mold心骨模型core iron printer心骨切断器core rod cutter心骨轴core spindle心裂(木材) heart shake心砂core sand心砂混合机core sand mixer心形镘刀large heart trowel心型拔出装置(压铸) core pull assembly心型撑,砂心撑chaplet心型固定门(压铸) heel block心型滑板(压铸) core slide心型移装,砂心移装core draw-back心轴,心骨arbor心座core bedding frame辛浦森式混砂机Sympson type sand mill新炼金属virgin metal新砂new sand锌(Zn) zinc锌当量zinc equivalence,zinc equivalent factor 通气口air port通气蜡条vent wax通气蜡线wax vent通气砂心blind core通气筛嘴(砂心盒) screen vent通气性vent abi通气针vent former通气针vent wire同素异性allotropy同位素isotope同质多象polymorphism桐油China wood oil酮油tung oil铜(Cu) copper铜基合金cupro-metal铜绿green patina铜气脆性(铸疵) hydrogen brittleness of copper 铜缘patina铜缘Verdigris筒状浇口(压铸) end gate头等品质top grade quality透明片transparent cut透气性permeability透气性试验permeability test透气性试验器permeability tester"凸出块,突耳casting lug凸疵(铸疵)(模型粘砂) sticker凸肩导销shoulder guider pin凸块,突耳lug凸片,飞边fin凸片管finned tube凸片气缸finned cylinder凸缘flange凸缘抹片flange sleeker突出标志rising mark突耳孔lughole突起分模面undulating mold joint涂焊(表面硬化涂焊) surfacing涂黑blacking涂浆,洗涤washing涂沥表管tarred pipe涂料facing materials涂料wash material涂料,涂模剂coat涂料,涂模剂coating涂料疤(铸疵) blacking scab涂料孔(铸疵) blacking hole涂模浆mold wash涂模浆molding wash涂模料mold coating涂模料mold dressing涂模料mold facing涂模料接种法mold coating inoculation涂刷painting土状石墨amorphous graphite吐粒散铁,吐粒散体trosstite钍(Th) thorium推拔,斜度taper推拔砂箱taper flask推拔套箱taper case推车式浇桶buggy ladle推挤(压铸) squeezing退火annealing退火罐annealing pot退火炉annealing furance (oven)退火温度annealing temperature退火箱annealing box退火用填料,退火用矿粉annealing ore退货rejection托板pallet托板输送机pallet conveyor托板输送机plate conveyer托架bracket托运板carrying plate脱件销(压铸) sprue puller pin脱蜡burn-out脱蜡dewaxing脱蜡法lost wax process脱蜡造模法lost wax molding脱裂强度(模砂式模纵面压裂试验) splitting strength 脱硫,去硫desulphurization脱硫,去硫desulphurizing脱模pattern draw脱模式造模机pattern-draw molding machine脱湿剂(模砂用) humectant脱碳decarburization脱碳法展性处理malleablization by decarburizing 脱碳率rate of decarburization脱硅desiliconizing脱锌dezincification椭圆导套oval bush外观检查outer inspection外角抹镘square sleeker外卡钳outside calipers外冷激,外冷硬,外冷铁extenal chill外模破裂broken mold外伸砂心顾clearance print外伸砂心头over-hang外伸余度砂心头clearance taper print外缩(铸疵) draw外缩孔(铸疵) open cavity外缩孔(铸疵) surface shrinkage外缩孔,凹陷(铸疵) depression外缩窝shrinkage depression外烯式空气预热器externally fired hot blast heater 外因非金属杂物exogenous non-metallic inclusion 外因金属夹杂物exogenous metallic in clusion外因凝固exogenous solidification外圆角round弯曲负荷bending load弯曲试验bending test弯头抹刀bent spatula完工面finished surface完全冷激complete chill完全燃烧complete combustion完全退火full annealing完整模型comple。

相关主题