印度IL&FS Cuddalore烟气脱硫工程安全滑触线技术规范书中国大唐科技工程有限公司2015年7月批准：审核：校核：编写：目录1．总则2．技术要求3．规范及数量4．供货范围5．技术服务6．需方工作7．工作安排8．备品备件及专用工具9．质量保证和试验10.包装、运输和储存1 总则1.0.l本技术规范书适用于印度IL&FS Cuddalore烟气脱硫工程安全滑触线。
它提出了安全滑触线的功能设计、结构、性能、安装和试验等方面的技术要求。
1.0.2本技术规范书提出的是最低限度的技术要求，并未对一切技术细节作出规定，也未充分引述有关标准和规范的条文，供方应提供符合工业标准和本规范书的优质产品。
1.0.3如果供方没有以书面形式对本规范书的条文提出异议，则意味着供方提供的材料（或系统）完全符合本规范书的要求。
如有异议，不管是多么微小，都应在投标书中以“对规范书的意见和同规范书的差异”为标题的专门章节中加以详细描述。
1.0.4本技术规范书所使用的标准如遇与供方所执行的标准不一致时，按较高标准执行。
1.0.5本技术规范书经供、需双方确认后作为订货合同的技术附件，与合同正文具有同等的法律效力。
1.0.6本技术规范书未尽事宜，由供需双方协商确定。
2 技术要求2.l应遵循的主要现行标准，均应为最新的国家或行业标准。
2.2 环境条件2.2.1工程概况The plant location details are as follows:Country : IndiaState : Tamil NaduAdministrative district : CuddaloreNext big cities to site : Cuddalore (approx.25 kms from site)Road access : National Highway (NH – 45A) (approx.2 kms from site)Nearest Railway Station : Alapakam ( approx.9 kms from site)Nearest Airport : Pondicherry (approx.50 kms from site)Chennai((approx.200 kms from site)Nearest Harbour : Cuddalore port (minor port)The proposed power plant will be located at Cuddalore in Tamil Nadu. The proposed power plant site is located at about 25km South of Cuddalore and about 5 km north of Porto Novo. The Land proposed falls invillages Kottattai, Ariyaghoshti Villiayannalur and Silambimangalam and bounded by Parangipettai on the south side. The proposed marine facilities for the power plant will be built on the coast adjoining the power plant. The site is accessible by well developed roads. Railway lines are also located adjacent to the western side of site boundary.The town of Cuddalore has all infrastructural facilities and has number of Industries. Cuddalore is well connected by both state highways, National highways and has direct rail link with Chennai. National Highway NH-45A (Villupuram-Puducherry-Cuddalore-Chidambaram-Nagapattinam Highway) passes through Cuddalore. Three state highways connect Cuddalore with other parts of Tamil Nadu are SH-9, SH-10 and SH-68.2.2.2 气象及使用环境条件2.2.2.1 Geological Conditions2.2.2.1.1 Soil ProfileA Preliminary geotechnical investigation is furnished as Part-III of this Tender Document.The Detailed geotechnical Investigation and Setting out survey may be performed by the contractor, if required, for the detailed engineering for the project. The geotechnical report will contain recommendations for foundation design during detailed engineering.2.2.2.1.2 Seismic intensitySeismic Intensity : As per IS : 1893 2005Zone : IIIIntensity : As per IS:1893-20052.2.2.1.3 Tide LevelsThe recorded tide levels with respect to the Chart Datum (CD) near the identified intake point are as follows:Mean high water-Spring : CD + 1.1 mMean high Water-Neap : CD + 0.9 mMean low Water-Neap : CD + 0.6 mMean low water-Spring: CD + 0.3mMean sea level: CD + 0.7 m2.2.2.2 Meteorological ConditionsAmbient Air TemperatureMaximum dry bulb temperature : 40°CMinimum dry bulb temperature : 19°CRelative humidityMean Maximum humidity(Summer): 90%Mean Minimum humidity(Summer): 65%RainfallAnnual rainfall (Maximum) : 280.2 mmWindWind Speed (max) : 180 km/hWind Speed annual mean : 11.8 km/h2.2.2.3 Site conditions:• Design Ambient DataDesign Ambient Wet bulb temperature : 28°CDesign Ambient Dry bulb temperature : 33°CThe maximum rainfall in a year to be considered for design is 280 mm in 24 hours and the hourly intensity to be considered is 40 mm./h.• Design ambient conditions for Steam Generator, fansDesign ambient temperature : 32°CDesign ambient air relative humidity : 67%• Design ambient Conditions for Electrical equipments sizing• For transformer : 50°C (as Per IS)• All other electrical equipment : 45°C• Relative Humidity Mean Maximum : 90%• Relative Humidity Mean Minimum : 65%2.2.2.4. Wind dataWind loads to be considered for design of structures shall be based on the design wind speeds arrived at based on IS : 875– Latest Edition The parameters for calculationof design wind speed as per IS : 875.2.2.2.5. Seismic DataSeismic loads to be considered for design of structures shall be as per as per IS : 1893.2.3 安全滑触线技术规格2.3.1 概述本次招标的安全滑触线用于印度IL&FS Cuddalore烟气脱硫工程电动葫芦的供电，安全滑触线必须是全新的采用先进技术设计制造，具有良好的安全性、可靠性，满足招标要求的全套产品。
2.3.2 生产厂资格认证及产品标准要求。
2.3.2.1 企业应具有GB9001-2000《质量管理体系认证》，国家3C强制认证。
2.3.2.2 产品执行JB/T6391《起重机滑接输电装置形式和基本要求》。
2.3.2.3 生产厂年销售滑触线40万米以上，生产滑触线十年以上，提供供货合同复印件等有效证明文件。
经有关审计部门认证盖章的年财务报表。
2.3.2.4 投标方需提供近2年的主要用户名单及供货量、联系人及电话。