#include <REG51.H>#include <intrins.h>#define uint unsigned int#define uchar unsigned charvoid Stopwatch(); //声明秒表函数void Clock(); //声明闹钟函数void Output(); //声明输出函数void important(); //声明重要函数（相当于mian()函数）void TLimit(); //声明调节温度上下限函数sbit DS1302_CLK = P1^7; //实时时钟时钟线引脚sbit DS1302_IO = P1^6; //实时时钟数据线引脚sbit DS1302_RST = P1^5; //实时时钟复位线引脚sbit wireless_1 = P3^0; //温度过上限标志sbit wireless_2 = P3^1; //温度适中标志sbit wireless_3 = P3^2; //温度过下限标志sbit fan = P3^4; //开风扇标志sbit clock=P3^5; //开关闹钟sbit setclock = P3^6; //闹钟开启控制sbit stopwatch = P3^7; //秒表开启控制sbit ACC0 = ACC^0;sbit ACC7 = ACC^7;char hide_sec,hide_min,hide_hour,hide_day,hide_week,hide_month,hide_year; //秒,分,时到日,月,年位闪的计数sbit Set = P2^0; //模式切换键sbit Up = P2^1; //加法按钮sbit Down = P2^2; //减法按钮sbit out = P2^3; //立刻跳出调整模式按钮sbit DQ = P1^0; //温度传送数据IO口char c3,c2=0;char c=0,LowerBonud=20,UpperLimit=30;char a1=0,a2=0,a3=0,a4=0;char k[8]={'0','0',':','0','0',':','0','0'};void InitTimer0(void)//产生10ms时间间隔{TMOD = (TMOD & 0XF0) | 0X01; //定时器0工作在模式1，16Bit定时器模式TH0 = (65536 - 8000)/256;TL0 = (65536 - 8000)%256;TR0 =1; ET0 =1;//开启定时器和中断EA = 1;}char done,count,temp,flag,up_flag,down_flag; //uchar temp_value; //温度值uchar TempBuffer[5],week_value[2],h[8]; //unsigned char NL[5];void show_time(); //液晶显示程序/***********1602液晶显示部分子程序****************///Port Definitions**********************************************************sbit LcdRs = P2^5;sbit LcdRw = P2^6;sbit LcdEn = P2^7;sfr DBPort = 0x80; //P0=0x80,P1=0x90,P2=0xA0,P3=0xB0.数据端口//内部等待函数************************************************************************** unsigned char LCD_Wait(void){LcdRs=0;LcdRw=1; _nop_();LcdEn=1; _nop_();LcdEn=0;return DBPort;}//向LCD写入命令或数据************************************************************#define LCD_COMMAND 0 // Command#define LCD_DATA 1 // Data#define LCD_CLEAR_SCREEN 0x01 // 清屏#define LCD_HOMING 0x02 // 光标返回原点void LCD_Write(bit style, unsigned char input){LcdEn=0;LcdRs=style;LcdRw=0; _nop_();DBPort=input; _nop_();//注意顺序LcdEn=1; _nop_();//注意顺序LcdEn=0; _nop_();LCD_Wait();}//设置显示模式************************************************************#define LCD_SHOW 0x04 //显示开#define LCD_HIDE 0x00 //显示关#define LCD_CURSOR 0x02 //显示光标#define LCD_NO_CURSOR 0x00 //无光标#define LCD_FLASH 0x01 //光标闪动#define LCD_NO_FLASH 0x00 //光标不闪动void LCD_SetDisplay(unsigned char DisplayMode){LCD_Write(LCD_COMMAND, 0x08|DisplayMode);}//设置输入模式************************************************************ #define LCD_AC_UP 0x02#define LCD_AC_DOWN 0x00 // default#define LCD_MOVE 0x01 // 画面可平移#define LCD_NO_MOVE 0x00 //defaultvoid LCD_SetInput(unsigned char InputMode){LCD_Write(LCD_COMMAND, 0x04|InputMode);}//初始化LCD************************************************************ void LCD_Initial(){LcdEn=0;LCD_Write(LCD_COMMAND,0x38); //8位数据端口,2行显示,5*7点阵LCD_Write(LCD_COMMAND,0x38);LCD_SetDisplay(LCD_SHOW|LCD_NO_CURSOR); //开启显示, 无光标LCD_Write(LCD_COMMAND,LCD_CLEAR_SCREEN); //清屏LCD_SetInput(LCD_AC_UP|LCD_NO_MOVE); //AC递增, 画面不动}//液晶字符输入的位置************************void GotoXY(unsigned char x, unsigned char y){if(y==0)LCD_Write(LCD_COMMAND,0x80|x);if(y==1)LCD_Write(LCD_COMMAND,0x80|(x-0x40));}//将字符输出到液晶显示void Print(unsigned char *str){while(*str!='\0')//while(*str!='\0'){LCD_Write(LCD_DATA,*str);str++;}}/***********DS1302时钟部分子程序******************/typedef struct SYSTEMTIME{unsigned char Second;unsigned char Minute;unsigned char Hour;unsigned char Week;unsigned char Day;unsigned char Month;unsigned char Year;unsigned char YearH;unsigned char YearL;unsigned char day;unsigned char month;unsigned char year;unsigned char DateString[11];unsigned char NLDateString[12];unsigned char TimeString[9];}SYSTEMTIME; //定义的时间类型SYSTEMTIME CurrentTime; //#define AM(X) X#define PM(X) (X+12) // 转成24小时制#define DS1302_SECOND 0x80 //时钟芯片的寄存器位置,存放时间#define DS1302_MINUTE 0x82#define DS1302_HOUR 0x84#define DS1302_WEEK 0x8A#define DS1302_DAY 0x86#define DS1302_MONTH 0x88#define DS1302_YEAR 0x8C#define DS1302_YEARH 0xC0void DS1302InputByte(unsigned char d) //实时时钟写入一字节(内部函数) {unsigned char i;ACC = d;for(i=8; i>0; i--){DS1302_IO = ACC0; //相当于汇编中的RRCDS1302_CLK = 1;DS1302_CLK = 0;ACC = ACC >> 1;}}unsigned char DS1302OutputByte(void) //实时时钟读取一字节(内部函数){unsigned char i;for(i=8; i>0; i--){ACC = ACC >>1; //相当于汇编中的RRCACC7 = DS1302_IO;DS1302_CLK = 1;DS1302_CLK = 0;}return(ACC);}void Write1302(unsigned char ucAddr, unsigned char ucDa) //ucAddr: DS1302地址, ucData: 要写的数据{DS1302_RST = 0;DS1302_CLK = 0;DS1302_RST = 1;DS1302InputByte(ucAddr); // 地址，命令DS1302InputByte(ucDa); // 写1Byte数据DS1302_CLK = 1;DS1302_RST = 0;}unsigned char Read1302(unsigned char ucAddr) //读取DS1302某地址的数据{unsigned char ucData;DS1302_RST = 0;DS1302_CLK = 0;DS1302_RST = 1;DS1302InputByte(ucAddr|0x01); // 地址，命令ucData = DS1302OutputByte(); // 读1Byte数据DS1302_CLK = 1;DS1302_RST = 0;return(ucData);}void DS1302_GetTime(SYSTEMTIME *Time) //获取时钟芯片的时钟数据到自定义的结构型数组{unsigned char ReadV alue;ReadValue = Read1302(DS1302_SECOND);Time->Second = ((ReadValue&0x70)>>4)*10 + (ReadValue&0x0F);ReadValue = Read1302(DS1302_MINUTE);Time->Minute = ((ReadV alue&0x70)>>4)*10 + (ReadValue&0x0F);ReadValue = Read1302(DS1302_HOUR);Time->Hour = ((ReadV alue&0x70)>>4)*10 + (ReadV alue&0x0F);ReadValue = Read1302(DS1302_DAY);Time->Day = ((ReadV alue&0x70)>>4)*10 + (ReadV alue&0x0F);ReadValue = Read1302(DS1302_WEEK);Time->Week = ((ReadValue&0x70)>>4)*10 + (ReadV alue&0x0F);ReadValue = Read1302(DS1302_MONTH);Time->Month = ((ReadValue&0x70)>>4)*10 + (ReadValue&0x0F);ReadValue = Read1302(DS1302_YEAR);Time->Year = ((ReadValue&0x70)>>4)*10 + (ReadV alue&0x0F);Time->YearH = 20;}void DateToStr(SYSTEMTIME *Time) //将时间年,月,日,星期数据转换成液晶显示字符串,放到数组里DateString[]{ if(hide_year<2) //这里的if,else语句都是判断位闪烁,<2显示数据,>2就不显示,输出字符串为2007/07/22{Time->DateString[0] = Time->YearH/10 + '0';Time->DateString[1] = Time->YearH%10 + '0';Time->DateString[2] = Time->Year/10 + '0';Time->DateString[3] = Time->Year%10 + '0';}else{Time->DateString[0] = ' ';Time->DateString[1] = ' ';Time->DateString[2] = ' ';Time->DateString[3] = ' ';}Time->DateString[4] = '/';if(hide_month<2){Time->DateString[5] = Time->Month/10 + '0';Time->DateString[6] = Time->Month%10 + '0';}else{Time->DateString[5] = ' ';Time->DateString[6] = ' ';}Time->DateString[7] = '/';if(hide_day<2){Time->DateString[8] = Time->Day/10 + '0';Time->DateString[9] = Time->Day%10 + '0';}else{Time->DateString[8] = ' ';Time->DateString[9] = ' ';}if(hide_week<2){week_value[0] = Time->Week%10 + '0'; //星期的数据另外放到week_value[]数组里,跟年,月,日的分开存放,因为等一下要在最后显示}else{week_value[0] = ' ';}week_value[1] = '\0';Time->DateString[10] = '\0'; //字符串末尾加'\0' ,判断结束字符}void TimeToStr(SYSTEMTIME *Time) //将时,分,秒数据转换成液晶显示字符放到数组TimeString[];{ if(hide_hour<2){Time->TimeString[0] = Time->Hour/10 + '0';Time->TimeString[1] = Time->Hour%10 + '0';h[0]=Time->TimeString[0];h[1]=Time->TimeString[1];}else{Time->TimeString[0] = ' ';Time->TimeString[1] = ' ';}Time->TimeString[2] = ':';h[2]=Time->TimeString[2];if(hide_min<2){Time->TimeString[3] = Time->Minute/10 + '0';Time->TimeString[4] = Time->Minute%10 + '0';h[3]=Time->TimeString[3];h[4]=Time->TimeString[4];}else{Time->TimeString[3] = ' ';Time->TimeString[4] = ' ';}Time->TimeString[5] = ':';h[5]=Time->TimeString[5];if(hide_sec<2){Time->TimeString[6] = Time->Second/10 + '0';Time->TimeString[7] = Time->Second%10 + '0';h[6]=Time->TimeString[6];h[7]=Time->TimeString[7];}else{Time->TimeString[6] = ' ';Time->TimeString[7] = ' ';}Time->DateString[8] = '\0';if ((a1==h[4])&&(a2==h[3])&&(a3<=h[7])&&((a4==h[6])||(a4==h[6]-1))) {clock=0;c=10;}}void Initial_DS1302(void) //时钟芯片初始化{unsigned char Second=Read1302(DS1302_SECOND);if(Second&0x80) //判断时钟芯片是否关闭{Write1302(0x8e,0x00); //写入允许Write1302(0xC0,0x20);Write1302(0x8c,0x09); //以下写入初始化时间日期:2007/07/25.星期: 3. 时间: 23:59:55 Write1302(0x88,0x06);Write1302(0x86,0x05);Write1302(0x8a,0x07); //xingqiWrite1302(0x84,0x23);Write1302(0x82,0x59);Write1302(0x80,0x55);Write1302(0x8e,0x80); //禁止写入}}/***********ds18b20子程序*************************//***********ds18b20延迟子函数（晶振12MHz ）*******/void delay_18B20(unsigned int i){while(i--);}/**********ds18b20初始化函数**********************/void Init_DS18B20(void){unsigned char x=0;DQ = 1; //DQ复位delay_18B20(8); //稍做延时DQ = 0; //单片机将DQ拉低delay_18B20(80); //精确延时大于480usDQ = 1; //拉高总线delay_18B20(14);x=DQ; //稍做延时后如果x=0则初始化成功x=1则初始化失败delay_18B20(20);}/***********ds18b20读一个字节**************/unsigned char ReadOneChar(void){uchar i=0;uchar dat = 0;for (i=8;i>0;i--){DQ = 0; // 给脉冲信号dat>>=1; //数据右移一位DQ = 1; // 给脉冲信号if(DQ)dat|=0x80; //按位或，取最高位delay_18B20(4);}return(dat);}/*************ds18b20写一个字节****************/void WriteOneChar(uchar dat){unsigned char i=0;for (i=8; i>0; i--){DQ = 0;DQ = dat&0x01; //取最低位delay_18B20(5);DQ = 1; //上升沿将数据送入dat>>=1;}}/**************读取ds18b20当前温度************/void ReadTemp(void){unsigned char a=0;unsigned char b=0;unsigned char t=0;Init_DS18B20();WriteOneChar(0xCC); // 跳过读序号列号的操作WriteOneChar(0x44); // 启动温度转换delay_18B20(100); // this message is wery importantInit_DS18B20();WriteOneChar(0xCC); //跳过读序号列号的操作WriteOneChar(0xBE); //读取温度寄存器等（共可读9个寄存器）前两个就是温度delay_18B20(100);a=ReadOneChar(); //读取温度值低位b=ReadOneChar(); //读取温度值高位temp_value=b<<4; //左移四位，扩大16倍，变为一个字节的高四位temp_value+=(a&0xf0)>>4;//取温度值的地位的高四位，右移四位后与温度的高四位相加得到温度值if (temp_value>=UpperLimit) {wireless_1 =0;fan=1;}else {wireless_1 =1;fan=0;}if ((temp_value>LowerBonud)&&(temp_value<UpperLimit)) wireless_2 =0;else wireless_2 =1;if (temp_value<=LowerBonud) wireless_3 =0;else wireless_3 =1;}void temp_to_str() //温度数据转换成液晶字符显示{TempBuffer[0]=temp_value/10+'0'; //十位TempBuffer[1]=temp_value%10+'0'; //个位TempBuffer[2]=0xdf; //温度符号TempBuffer[3]='C';TempBuffer[4]='\0';}void Delay1ms(unsigned int count){unsigned int i,j;for(i=0;i<count;i++)for(j=0;j<120;j++){if (!stopwatch) {c++;Stopwatch();}if (!setclock) {c2++;Clock();}if ((!out)&&(!Set)) {TLimit();}if (!out) clock=1; //关闭闹钟}}/*延时子程序*/void mdelay(uint delay){ uint i;for(;delay>0;delay--)for(i=0;i<32;i++); //1ms延时.}/*****************************阳历转换阴历***********************************/ code unsigned char year_code[597]={0x04,0xAe,0x53, //1901 00x0A,0x57,0x48, //1902 30x55,0x26,0xBd, //1903 60x0d,0x26,0x50, //1904 90x0d,0x95,0x44, //1905 120x46,0xAA,0xB9, //1906 150x05,0x6A,0x4d, //1907 180x09,0xAd,0x42, //1908 210x24,0xAe,0xB6, //19090x04,0xAe,0x4A, //19100x6A,0x4d,0xBe, //19110x0A,0x4d,0x52, //19120x0d,0x25,0x46, //19130x5d,0x52,0xBA, //19140x0B,0x54,0x4e, //19150x0d,0x6A,0x43, //19160x29,0x6d,0x37, //19170x09,0x5B,0x4B, //19180x74,0x9B,0xC1, //19190x04,0x97,0x54, //19200x0A,0x4B,0x48, //19210x5B,0x25,0xBC, //19220x06,0xA5,0x50, //19230x06,0xd4,0x45, //19240x4A,0xdA,0xB8, //19250x02,0xB6,0x4d, //19260x09,0x57,0x42, //19270x24,0x97,0xB7, //19280x04,0x97,0x4A, //19290x66,0x4B,0x3e, //19300x0d,0x4A,0x51, //19310x0e,0xA5,0x46, //19320x56,0xd4,0xBA, //19330x05,0xAd,0x4e, //19340x02,0xB6,0x44, //19350x39,0x37,0x38, //19360x09,0x2e,0x4B, //19370x0C,0x95,0x53, //1939 0x0d,0x4A,0x48, //1940 0x6d,0xA5,0x3B, //1941 0x0B,0x55,0x4f, //1942 0x05,0x6A,0x45, //1943 0x4A,0xAd,0xB9, //1944 0x02,0x5d,0x4d, //1945 0x09,0x2d,0x42, //1946 0x2C,0x95,0xB6, //1947 0x0A,0x95,0x4A, //1948 0x7B,0x4A,0xBd, //1949 0x06,0xCA,0x51, //1950 0x0B,0x55,0x46, //1951 0x55,0x5A,0xBB, //1952 0x04,0xdA,0x4e, //1953 0x0A,0x5B,0x43, //1954 0x35,0x2B,0xB8, //1955 0x05,0x2B,0x4C, //1956 0x8A,0x95,0x3f, //1957 0x0e,0x95,0x52, //1958 0x06,0xAA,0x48, //1959 0x7A,0xd5,0x3C, //1960 0x0A,0xB5,0x4f, //1961 0x04,0xB6,0x45, //1962 0x4A,0x57,0x39, //1963 0x0A,0x57,0x4d, //1964 0x05,0x26,0x42, //1965 0x3e,0x93,0x35, //1966 0x0d,0x95,0x49, //1967 0x75,0xAA,0xBe, //1968 0x05,0x6A,0x51, //1969 0x09,0x6d,0x46, //1970 0x54,0xAe,0xBB, //1971 0x04,0xAd,0x4f, //1972 0x0A,0x4d,0x43, //1973 0x4d,0x26,0xB7, //1974 0x0d,0x25,0x4B, //1975 0x8d,0x52,0xBf, //1976 0x0B,0x54,0x52, //1977 0x0B,0x6A,0x47, //1978 0x69,0x6d,0x3C, //1979 0x09,0x5B,0x50, //1980 0x04,0x9B,0x45, //19810x0A,0x4B,0x4d, //19830xAB,0x25,0xC2, //19840x06,0xA5,0x54, //19850x06,0xd4,0x49, //19860x6A,0xdA,0x3d, //19870x0A,0xB6,0x51, //19880x09,0x37,0x46, //19890x54,0x97,0xBB, //19900x04,0x97,0x4f, //19910x06,0x4B,0x44, //19920x36,0xA5,0x37, //19930x0e,0xA5,0x4A, //19940x86,0xB2,0xBf, //19950x05,0xAC,0x53, //19960x0A,0xB6,0x47, //19970x59,0x36,0xBC, //19980x09,0x2e,0x50, //1999 294 0x0C,0x96,0x45, //2000 297 0x4d,0x4A,0xB8, //20010x0d,0x4A,0x4C, //20020x0d,0xA5,0x41, //20030x25,0xAA,0xB6, //20040x05,0x6A,0x49, //20050x7A,0xAd,0xBd, //20060x02,0x5d,0x52, //20070x09,0x2d,0x47, //20080x5C,0x95,0xBA, //20090x0A,0x95,0x4e, //20100x0B,0x4A,0x43, //20110x4B,0x55,0x37, //20120x0A,0xd5,0x4A, //20130x95,0x5A,0xBf, //20140x04,0xBA,0x53, //20150x0A,0x5B,0x48, //20160x65,0x2B,0xBC, //20170x05,0x2B,0x50, //20180x0A,0x93,0x45, //20190x47,0x4A,0xB9, //20200x06,0xAA,0x4C, //20210x0A,0xd5,0x41, //20220x24,0xdA,0xB6, //20230x04,0xB6,0x4A, //20240x69,0x57,0x3d, //20250x0d,0x26,0x46, //2027 0x5e,0x93,0x3A, //2028 0x0d,0x53,0x4d, //2029 0x05,0xAA,0x43, //2030 0x36,0xB5,0x37, //2031 0x09,0x6d,0x4B, //2032 0xB4,0xAe,0xBf, //2033 0x04,0xAd,0x53, //2034 0x0A,0x4d,0x48, //2035 0x6d,0x25,0xBC, //2036 0x0d,0x25,0x4f, //2037 0x0d,0x52,0x44, //2038 0x5d,0xAA,0x38, //2039 0x0B,0x5A,0x4C, //2040 0x05,0x6d,0x41, //2041 0x24,0xAd,0xB6, //2042 0x04,0x9B,0x4A, //2043 0x7A,0x4B,0xBe, //2044 0x0A,0x4B,0x51, //2045 0x0A,0xA5,0x46, //2046 0x5B,0x52,0xBA, //2047 0x06,0xd2,0x4e, //2048 0x0A,0xdA,0x42, //2049 0x35,0x5B,0x37, //2050 0x09,0x37,0x4B, //2051 0x84,0x97,0xC1, //2052 0x04,0x97,0x53, //2053 0x06,0x4B,0x48, //2054 0x66,0xA5,0x3C, //2055 0x0e,0xA5,0x4f, //2056 0x06,0xB2,0x44, //2057 0x4A,0xB6,0x38, //2058 0x0A,0xAe,0x4C, //2059 0x09,0x2e,0x42, //2060 0x3C,0x97,0x35, //2061 0x0C,0x96,0x49, //2062 0x7d,0x4A,0xBd, //2063 0x0d,0x4A,0x51, //2064 0x0d,0xA5,0x45, //2065 0x55,0xAA,0xBA, //2066 0x05,0x6A,0x4e, //2067 0x0A,0x6d,0x43, //2068 0x45,0x2e,0xB7, //20690x8A,0x95,0xBf, //20710x0A,0x95,0x53, //20720x0B,0x4A,0x47, //20730x6B,0x55,0x3B, //20740x0A,0xd5,0x4f, //20750x05,0x5A,0x45, //20760x4A,0x5d,0x38, //20770x0A,0x5B,0x4C, //20780x05,0x2B,0x42, //20790x3A,0x93,0xB6, //20800x06,0x93,0x49, //20810x77,0x29,0xBd, //20820x06,0xAA,0x51, //20830x0A,0xd5,0x46, //20840x54,0xdA,0xBA, //20850x04,0xB6,0x4e, //20860x0A,0x57,0x43, //20870x45,0x27,0x38, //20880x0d,0x26,0x4A, //20890x8e,0x93,0x3e, //20900x0d,0x52,0x52, //20910x0d,0xAA,0x47, //20920x66,0xB5,0x3B, //20930x05,0x6d,0x4f, //20940x04,0xAe,0x45, //20950x4A,0x4e,0xB9, //20960x0A,0x4d,0x4C, //20970x0d,0x15,0x41, //20980x2d,0x92,0xB5, //2099};//月份数据表code unsigned char day_code1[9]={0x0,0x1f,0x3b,0x5a,0x78,0x97,0xb5,0xd4,0xf3};code unsigned int day_code2[3]={0x111,0x130,0x14e};/**************************************************************************** * 子函数,用于读取数据表中农历月的大月或小月,如果该月为大返回1,为小返回0****************************************************************************/ bit GetMoonDay(unsigned char month_p,unsigned short table_addr){switch (month_p){case 1:if((year_code[table_addr]&0x08)==0) return(0);else return(1);case 2:if((year_code[table_addr]&0x04)==0) return(0);else return(1);case 3:if((year_code[table_addr]&0x02)==0) return(0);else return(1);case 4:if((year_code[table_addr]&0x01)==0) return(0);else return(1);case 5:if((year_code[table_addr+1]&0x80)==0) return(0);else return(1);case 6:if((year_code[table_addr+1]&0x40)==0) return(0);else return(1);case 7:if((year_code[table_addr+1]&0x20)==0) return(0);else return(1);case 8:if((year_code[table_addr+1]&0x10)==0) return(0);else return(1);case 9:if((year_code[table_addr+1]&0x08)==0) return(0);else return(1);case 10:if((year_code[table_addr+1]&0x04)==0) return(0);else return(1);case 11:if((year_code[table_addr+1]&0x02)==0) return(0);else return(1);case 12:if((year_code[table_addr+1]&0x01)==0) return(0);else return(1);case 13:if((year_code[table_addr+2]&0x80)==0) return(0);else return(1);}return(0);}/****************************************************************************** ***************************** 函数名称:GetChinaCalendar** 功能描述:公农历转换(只允许1901-2099年)** 输入: year 公历年** month 公历月** day 公历日** p 储存农历日期地址** 输出: 1 成功** 0 失败** 作者: Campo** 修改: 赖皮** 日期: 2007年02月06日**-------------------------------------------------------------------------------------------------------** 修改人:** 日期:**------------------------------------------------------------------------------------------------------******************************************************************************* *************************/unsigned char GetChinaCalendar(unsigned int year,unsigned char month,unsigned char day){unsigned char temp1,temp2,temp3,month_p,yearH,yearL;unsigned char flag_y;unsigned short temp4,table_addr;yearH=year/100; yearL=year%100;if((yearH!=19)&&(yearH!=20)) return(0);// 定位数据表地址if(yearH==20) table_addr=(yearL+100-1)*3;else table_addr=(yearL-1)*3;// 取当年春节所在的公历月份temp1=year_code[table_addr+2]&0x60;temp1>>=5;// 取当年春节所在的公历日temp2=year_code[table_addr+2]&31;// 计算当年春年离当年元旦的天数,春节只会在公历1月或2月if(temp1==1) t emp3=temp2-1;else temp3=temp2+31-1;// 计算公历日离当年元旦的天数if (month<10) temp4=day_code1[month-1]+day-1;else temp4=day_code2[month-10]+day-1;// 如果公历月大于2月并且该年的2月为闰月,天数加1if ((month>2)&&(yearL%4==0)) temp4++;// 判断公历日在春节前还是春节后if (temp4>=temp3){temp4-=temp3;month=1;month_p=1;flag_y=0;if(GetMoonDay(month_p,table_addr)==0) temp1=29; //小月29天else temp1=30; //大小30天// 从数据表中取该年的闰月月份,如为0则该年无闰月temp2=year_code[table_addr]/16;while(temp4>=temp1){temp4-=temp1;month_p++;if(month==temp2){NL[4]='R';flag_y=~flag_y;if(flag_y==0) {month++;NL[4]=' ';}}else {month++;NL[4]=' ';}if(GetMoonDay(month_p,table_addr)==0) temp1=29;else temp1=30;}day=temp4+1;}// 公历日在春节前使用下面代码进行运算else{temp3-=temp4;if (yearL==0){yearL=100-1;yearH=19;}else yearL--;table_addr-=3;month=12;temp2=year_code[table_addr]/16;if (temp2==0) {month_p=12;NL[4]=' ';}else {month_p=13;NL[4]='R';}flag_y=0;if(GetMoonDay(month_p,table_addr)==0) temp1=29;else temp1=30;while(temp3>temp1){temp3-=temp1;month_p--;if(flag_y==0) month--;if(month==temp2) flag_y=~flag_y;if(GetMoonDay(month_p,table_addr)==0) temp1=29;else temp1=30;}day=temp1-temp3+1;}/////////////////////////NL[0]=yearH;NL[1]=yearL;NL[2]=month;NL[3]=day;return(1);}void zhuan(SYSTEMTIME *Time){GetChinaCalendar(Time->YearH*100+Time->Year,Time->Month,Time->Day);Time->day = NL[3];Time->month =NL[2];//将时间年,月,日,星期数据转换成液晶显示字符串,放到数组里DateString[]if(hide_year<2) //这里的if,else语句都是判断位闪烁,<2显示数据,>2就不显示,输出字符串为2007/07/22{Time->NLDateString[0] = NL[0]/10 + '0';Time->NLDateString[1] = NL[0]%10 + '0';Time->NLDateString[2] = NL[1]/10 + '0';Time->NLDateString[3] = NL[1]%10 + '0';}else{Time->NLDateString[0] = ' ';Time->NLDateString[1] = ' ';Time->NLDateString[2] = ' ';Time->NLDateString[3] = ' ';}Time->NLDateString[4] = '/';if(hide_month<2){Time->NLDateString[5] =NL[4] ;Time->NLDateString[6] = Time->month/10 + '0';Time->NLDateString[7] = Time->month%10 + '0';}else{Time->NLDateString[6] = ' ';Time->NLDateString[7] = ' ';}Time->NLDateString[8] = '/';if(hide_day<2){Time->NLDateString[9] = Time->day/10 + '0';Time->NLDateString[10] = Time->day%10 + '0';}else{Time->NLDateString[9] = ' ';Time->NLDateString[10] = ' ';}Time->NLDateString[11] = '\0'; //字符串末尾加'\0' ,判断结束字符//////////////////////}//显示天干生肖void lcd_digan(){temp = NL[1]%12;switch(temp){case 0: GotoXY(3,0); Print("Chen LongYear");//龙break;case 1: GotoXY(3,0); Print("Si She ear");//蛇break;case 2: GotoXY(3,0); Print("Wu Ma Year");//马break;case 3: GotoXY(3,0); Print("Wei YangYear"); //羊break;case 4: GotoXY(3,0); Print("Chen Hou Year"); //猴break;case 5: GotoXY(3,0); Print("You Ji Year"); //鸡break;case 6: GotoXY(3,0); Print("Xu Gou Year"); //狗break;case 7: GotoXY(3,0); Print("Hai Zhu Year"); //猪break;case 8: GotoXY(3,0); Print("Zi Shu Year"); //鼠break;case 9: GotoXY(3,0); Print("Chou Niu Year"); //牛break;case 10:GotoXY(3,0); Print("Yin Hu Year"); //虎break;case 11:GotoXY(3,0); Print("Mao Tu Year"); //兔break;}}//显示天支void lcd_tianzhi(){temp = NL[1]%10;switch(temp){case 0: GotoXY(0,0); Print("Gen");//庚break;case 1: GotoXY(0,0); Print("Xin");//辛break;case 2: GotoXY(0,0); Print("Ren");//壬break;case 3: GotoXY(0,0); Print("Gui"); //癸?break;case 4: GotoXY(0,0); Print("Jia"); //甲break;case 5: GotoXY(0,0); Print("Yi"); //乙break;case 6: GotoXY(0,0); Print("Bin"); //丙break;case 7: GotoXY(0,0); Print("Din"); //丁break;case 8: GotoXY(0,0); Print("Wu"); //戊break;case 9: GotoXY(0,0); Print("Ji");//己break;}}void outkey() //跳出调整模式,返回默认显示{ uchar Second;if(out==0)//if(out==0||wireless_1==1) //{ mdelay(4);count=0;hide_sec=0,hide_min=0,hide_hour=0,hide_day=0,hide_week=0,hide_month=0,hide_year=0;Second=Read1302(DS1302_SECOND);Write1302(0x8e,0x00); //写入允许Write1302(0x80,Second&0x7f);Write1302(0x8E,0x80); //禁止写入done=0;while(out==0);//while(wireless_1==1);}}////////////////////////////////////////////////////////////////////////////////////////////////////////////void Upkey()//升序按键{Up=1;if(Up==0)//if(Up==0||wireless_2==1){mdelay(4);switch(count){case 1:temp=Read1302(DS1302_SECOND); //读取秒数temp=temp+1; //秒数加1up_flag=1; //数据调整后更新标志if((temp&0x7f)>0x59) //超过59秒,清零temp=0;break;case 2:temp=Read1302(DS1302_MINUTE); //读取分数temp=temp+1; //分数加1up_flag=1;if(temp>0x59) //超过59分,清零temp=0;break;case 3:temp=Read1302(DS1302_HOUR); //读取小时数temp=temp+1; //小时数加1up_flag=1;if(temp>0x23) //超过23小时,清零temp=0;break;case 4:temp=Read1302(DS1302_WEEK); //读取星期数temp=temp+1; //星期数加1up_flag=1;if(temp>0x7)temp=1;break;case 5:temp=Read1302(DS1302_DAY); //读取日数temp=temp+1; //日数加1up_flag=1;if(temp>0x31)temp=1;break;case 6:temp=Read1302(DS1302_MONTH); //读取月数temp=temp+1; //月数加1up_flag=1;if(temp>0x12)temp=1;break;case 7:temp=Read1302(DS1302_YEAR); //读取年数temp=temp+1; //年数加1up_flag=1;if(temp>0x85)temp=0;break;default:break;}while(Up==0);//while(wireless_2==1);}}////////////////////////////////////////////////////////////////////////////////////////////////////////////void Downkey()//降序按键{Down=1;if(Down==0)//if(Down==0||wireless_3==1){mdelay(4);switch(count){case 1:temp=Read1302(DS1302_SECOND); //读取秒数temp=temp-1; //秒数减1down_flag=1; //数据调整后更新标志if(temp==0x7f) //小于0秒,返回59秒temp=0x59;break;case 2:temp=Read1302(DS1302_MINUTE); //读取分数temp=temp-1; //分数减1down_flag=1;if(temp==-1)temp=0x59; //小于0秒,返回59秒break;case 3:temp=Read1302(DS1302_HOUR); //读取小时数temp=temp-1; //小时数减1down_flag=1;if(temp==-1)temp=0x23;break;case 4:temp=Read1302(DS1302_WEEK); //读取星期数temp=temp-1; //星期数减1down_flag=1;if(temp==0)temp=0x7;;break;case 5:temp=Read1302(DS1302_DAY); //读取日数temp=temp-1; //日数减1down_flag=1;if(temp==0)temp=31;break;case 6:temp=Read1302(DS1302_MONTH); //读取月数temp=temp-1; //月数减1down_flag=1;if(temp==0)temp=12;break;case 7:temp=Read1302(DS1302_YEAR); //读取年数temp=temp-1; //年数减1down_flag=1;if(temp==-1)temp=0x85;break;default:break;}while(Down==0);//while(wireless_3==1);}}void Setkey()//模式选择按键{Set=1;if(Set==0)//if(Set==0||wireless_4==1){mdelay(4);count=count+1; //Setkey按一次,count就加1done=1; //进入调整模式while(Set==0);//while(wireless_4==1);}}void keydone()//按键功能执行{ uchar Second;if(flag==0) //关闭时钟,停止计时{ Write1302(0x8e,0x00); //写入允许temp=Read1302(0x80);Write1302(0x80,temp|0x80);Write1302(0x8e,0x80); //禁止写入flag=1;。