1. Scope :
This specification applies for the RL series of alloy film chip resistors made by TA-I.
2. Construction: Over Coat Conductor : (Lead-free )
Sn Plating
Ambient Temp.( Figure 1 6. Reliability Test:
Test Item
Temperature Coefficient of Resistance
)
Reference standard
IEC60115-1-4.8 JIS-C5201-1-4.8
Condition of Test
7.2 Type: 0603 7.2.1 E96: 1%
When the marking space is too small in such small-sized resistors as RL06, the marking can not made by 4 digits and may be made by two digits combined with one English capital. Significant figures of nominal resistance
Note* :RCWV : Rated continuous working voltage .
深圳捷比信－－高品质精密元件供应商
ｗｗｗ．ｊｅｐｓｕｎ．ｃｏｍ
Document No TRL-XX0S001N Issued date Page.
2013/06/04 4/9
Alloy Film Chip Resistors
Symbol 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Symbol for multipliers E24 10 11 12 13 15 16 18 20 22 24 27 30 33 36 39 43 47 51 56 62 68 75 82 91 E96 100 110 130 150
2.5 X rated voltage, 5s
Load Life
IEC60115-1-4.25.1 JIS-C5201-1-4.25.1
1%: (1%+0.001 ) 1000 hours at rated power , 70 , 1.5hours “ON “, 0.5hour “OFF” 2%,5%: (3%+0.001 ) Remark : 0402(3%+0.005 ) 1000 hours at rated power , 40 2 , 90~95% RH 1.5hours “ON “, 0.5hour “OFF” -55 (30 min. ) / +155 5 cycles (30 min.) 1%: (1%+0.001 ) 2%,5%: (3%+0.001 ) Remark : 0402(3%+0.005 ) 1%+0.005
270 5
solder , 10 1 sec dwell .
1%+0.005
At least 95% of surface area of electrode shall be covered with new solder.
Solderability Robustness of Termination (Bending Strength) Resistance to Dry Heat
深圳捷比信－－高品质精密元件供应商
ｗｗｗ．ｊｅｐｓｕｎ．ｃｏｍ
Document No TRL-XX0S001N Issued date Page.
2013/06/04 1/9
Alloy Film Chip Resistors
Low Resistห้องสมุดไป่ตู้nce (Standard) Halogen-Free
Low Resistance (Standard) Halogen-Free
7. Marking 7.1 Type: 0805,1206,2010,2512 7.1.1 E96: 1%
Resistance value is expressed by 4 digits, the first “R” means decimal point and the other digits represent for the normal resistance in . e.g., R100 =100 m
o o
Characteristics
1/16W
Measurement Method
1W JIS Code 3A / JIS Code 3D Refer to JIS C 5201-1-4.5
RL06 RL10 RL12 RL20 RL25 1/8W 1/4W 1/2W 3/4W
100 ~ 910
100~500m 501~910m : : 300 200
04-0402(1005) 1/16W 06-0603(1608) 1/8W 10-0805(2012) 1/4W 12-1206(3216) 1/2W 20-2010(5025) 3/4W 25-2512(6432) 1W
JGF-
5% 2% 1%
T-Paper Tape E-Embossed Tape N-Lead Free
245 5 solder, 2 0.5 sec dwell. Solder : Sn96.5 / Ag3.0 / Cu0.5 3mm deflection 2mm deflection (RL20,25) 155 5 for 96 4hrs
1%+0.005Ω 1%: (1%+0.005 ) 2%,5%: (2%+0.005 )
7.1.2
E24: 2%,5%
Resistance value is expressed by 3 digits, the first “R” means decimal point and the other digits represent for the normal resistance in . e.g., R10 =100 m
Alloy Film Chip Resistors
Low Resistance (Standard) Halogen-Free
4. Dimensions:
UNIT: mm
Type
RL04 RL06 RL10 RL12 RL20 RL25
L
1.00 -0.05 1.60 2.00 3.10 5.00 6.30 0.10 0.10 0.20 0.20 0.20
7.2.2 E24: 2%,5%
Resistance value is expressed by 3 digits, the first “0” means decimal point and the other digits represent for the normal resistance in . e.g., 010 =100 m
+0.10
W
0.50 0.80 1.25 1.55 2.50 3.20 0.05 0.10 0.10 0.10 0.20 0.20 0.20 0.30 0.40 0.50 0.60 0.60
C
0.10 0.20 0.20 0.30 0.30 0.30 0.25 0.35 0.35 0.40 0.50 0.50
深圳捷比信－－高品质精密元件供应商
ｗｗｗ．ｊｅｐｓｕｎ．ｃｏｍ
Document No TRL-XX0S001N Issued date Page.
2013/06/04 5/9
Alloy Film Chip Resistors
Low Resistance (Standard) Halogen-Free
Ni Plating Ceramic Substrate Resistive Element
3. Type Designation:
RL
Product Code RL : Chip Resistor
10
Size Power Rating
F
Tolerance
TN
Packaging
R100
Nominal Resistance
-55 ~ +125
Test Limits
Refer to paragraph 5 1%: (1%+0.005 ) 2%,5%: (3%+0.005 ) Remark : 0402(2%+0.005 )
Short Time Overload
IEC60115-1-4.13 JIS-C5201-1-4.13
d
0.10 0.20 0.20 0.20 0.25 0.25 0.35 0.45 0.50 0.55 0.55 0.55
t
0.05 0.10 0.10 0.10 0.10 0.10
5. Electrical characteristics :
Feature
RL04 Power Ratings (W) Resistance Value (m) T.C.R ( ppm / C ) Operation Temperature Range( C) Resistance Tolerance (%) Insulation Resistance (M) Maximum Working Voltage (V)
深圳捷比信－－高品质精密元件供应商
ｗｗｗ．ｊｅｐｓｕｎ．ｃｏｍ
Document No TRL-XX0S001N Issued date Page.