3. Features
1) Transfer Mold Package. 2) Wide Operating Supply voltage 2.7V ~ 5.5V 3) Supply Current : 3.0V(0.4mA), 5.0V(0.42mA) 4) Band pass filter center frequency : 20 ~ 60Khz 5) Epoxy IR filter characteristic : 810n~940nmm 6) Maximum interference safety against optical and electrical disturbance. 7) Internal filter for a high frequency lighting fluorescent lamp. 8) Internal Pull-Up output. 9) Operation with short burst possible. 10) Lead(Pb)-free component.
. Vcc
2.7
-
5.5
V
N/Signal (3.0V) 0.3 0.4 0.5
㎃
Icc
N/Signal (5.0V 0.35 0.42 0.6
㎃
Peak Wavelength (※1)
λp
-
940
-
㎚
B.P.F Center Frequency
fo
36
-
60
㎑
High Level Output Voltage (※1)
Future Technology of Optical Sensor
Miniature Infrared Remote Control Receiver
.
OS-OPTO TECHNOLOGY CO;LTD ADD:Bridge Wing Building 1008,Qiaotao,Fu Yong Town,Bao'an District, Shenzhen,Guangdogn,China TEL:755-27361616 MB:13556894958 FAX;755-33119977 Http:// Email:adam@
▶ Minimum Burst Length (tburst ) : 12pulses ▶ Minimum Gap Time Between the burst
(tburst gap) : 16pulses
Data word
tdata
tpause
Data word
▶ Minimum Gap Time between the data commands (tpause) : 23㎳
4. Absolute Maximum Ratings
.
1) Supply Voltage : 6.0V
2) Supply Current : 2.0mA
3) Operating Temperature : -20℃ ~ +85℃
4) Storage Temperature : -30℃ ~ +90℃
Ta=+121℃ 100%RH, P=1atm, t=4hr
. Ta=+350±5℃, 3s
Consumption current ICC < 1.0mA D (Vcc=5.0V)
C=0 / n=22 C=0 / n=11
satisfies the standard (fig.2, fig3) under the conditions below against the standard transmitter.
ON/OFF pulse width is to be satisfied within 0.3m~ arrival distance length.
4) Carrier Frequency
Type
OS-○○ 32○○ OS-○○ 36○○ OS-○○38○○ OS-○○40○○ OS-○○ 56○○
Carrier Frequency
32.7 ㎑ 36.0 ㎑ 37.9 ㎑ 40.0 ㎑ 56.7 ㎑
3
SHENZHEN OS-OPTO TECHNOLOGY CO;LTD
Ta=-20℃, Vcc=5.0V t=500hr
High level output voltage C=0 / n=22
VOH > 4.5V
High Temp./ High Hum. 5
Bias (※1,※2)
Ta=+85℃, 85%RH VCC=5.0V, t=500hr
VOL (Vcc=5.0V) C=0 / n=22
Low level output voltage
Temperature Cycle 6
(※2, ※3)
Ta=-20℃(0.5h) to +85℃(0.5h) 20cycle
VOL < 0.4V ICC (Vcc=5.0V)
C=0 / n=22
7 P.C.T (※2) 8 Solder Heat (※2)
① Confidence level : 90% ② LTPD : 10% / 20%
No.
Test Item
Test Conditions
Judgment Standard
Fail(c) / Samples(n)
1 High Temp. Storage (※2) Ta=+90℃, t=500hr
C=0 / n=22
GND
2
SHENZHEN OS-OPTO TECHNOLOGY CO;LTD

OS - Series
6. Electro-Optical Characteristics
1) Absolute Maximum Ratings
Parameter
Symbol
Supply Voltage
(at 25℃ Unless otherwise note)
Ratings
Unit
6.0
V
2.0
㎃
-20 ~ +85
℃
-30 ~ +90
℃
260, t<10sec
℃
2) Recommended Operating Conditions
Parameter
Operating Voltage Input Frequency
tWH
Period = 1.2㎳

400
-
800 ㎲
Internal Pull_up Resistance
Rout
94
㏀
Arrival Distance (※1)
±0˚
-
13
-
m
D
±30˚
-
11
-
m
Output Form
Active Low Output
※1. Distance between emitter and detector specifies maximum distance that output wave form
Rev3.0 (100101)
OS - Series
1. Application This Specification is applied to inspection and approval of the IR Receiver Module for Infrared Remote Control Application.
2. Description
The OS-Series are miniaturized r eceiver for infrared remote control system. The Pin Photodiode and preamplifier are assembled on lead frame. The epoxy package is designed as IR filter. The module has excellent performance even in disturbed ambient light application and provides protection against uncontrolled output pulses.
Symbol
Vcc fin
Ratings
2.7 ~ 5.5 20 ~ 60
Unit
V ㎑
3) Electro-Optical Characteristics
(Ta=25℃)
Parameter
Supply Voltage
Supply Current
Symbol Conditions Min Typ Max Unit
0˚
20˚
40˚
100
60˚
V
90
H
80˚
80 60 40 20 0 Relative Sensitivity(%)
4
SHENZHEN OS-OPTO TECHNOLOGY CO;LTD

OS - Series
7. Reliability Test Item and Standard. 1) All output products shall satisfy below Reliability test items. 2) Related sampling quantity and acceptance/failure judgment standard accordance with MIL standard MIL-STD-883 is as listed below.
5. Functional Block Diagram