毕业设计中英文翻译英文原文Hard gear processing[abstract ]uses in the power drive gear and the gear box, its size request smaller, the gear drive noise is lower, thus causes to the hard gear demand, also gave the gear manufacturer to propose explored the gear to process the new method the request OutlineUses in the power drive gear and the gear box, its size request smaller, the gear drive noise is lower, thus causes to the hard gear demand, also gave the gear manufacturer to propose explored the gear to process the new method the request. The gear in the hard heat treatment process, its material organization and the stress change, usually can cause the gear to have the distortion, namely tooth profile, tooth to and tooth pitch error. This this error will cause the tooth profile not correctly to mesh in the transmission time, thus has enlarged the load, will have the gear noise. Therefore, the hard gear after the heat treatment, should increase together the precision work working procedure generally.The hard gear precision work craft may divide into two kinds: A kind is uses non- formed the cutting edge, like the gear rubs truncates the processing; Another kind then is has formed the cutting edge like hard gear (HRC48 ~ 53) to roll truncates the processing.This article strongly will discuss will use in hardly rolling the hard alloy tools forming cutting edge precision work process which the tooth will process. The now hard alloy material, the cutting tool coating and the gear-hobbing machine technology development, has caused the hard gear to roll cuts the processing technology to have the remarkable enhancement, specially is smaller than in the processing or was equal to when 12DP center small modulus gear, may withstand the enormous cutting force which in the hard cutting process produces.Hard alloy hob selectionThe hard alloy hob has the very big progress in the material variety specification. Superfine, is thin, medium or the big pellet hard alloy now all has the product. In addition, the hard alloy hob semifinished materials formed craft technology also had the remarkable enhancement, like uses static pressure and so on heat (HIP) the craft, this craft under the high-pressured high temperature, increased the hard alloy semifinished materials intrinsic binding force, enhanced the hard alloy anti- curved intensity. According to the ISO stipulation, the entity hard alloy material may differently divide into certain kinds according to the application situation: The gear cutting tool divides into K kind and P kind, K kind of hard alloy has a higherresistance to wear, P kind then has the better high temperature red hardness. In the K trademark and in the P trademark hard alloy, each kind of trademark hard alloy granular structure is different, from medium pellet to superfine pellet. Each kind of trademark all has its application situation, this is and the granular structure is connected. Generally speaking, regarding softly rolls truncates, the K analogy P kind of performance is friends with, K kind of hard alloy can obtain a micron level the granular structure (granularity to be smaller than 0.5 mu m), but P kind then is not good. In abrasion aspect, K kind of toughness better, the life is longer.The hob resharpens and renovatesAfter the hob processing certain quantity work piece, its cutting edge failure, this time must resharpen. Sharpens the after hob to have to maintain the original geometry shape; The cutting edge must be sharp; The cutting tool golden phase structure cannot because rub truncates the heat but to destroy. Thus when sharpens the hard alloy hob should use one kind of oil base refrigerant, it does not get up to the chlorine and the sulfur the response. Regarding scrapes the hob, sharpens after the coating not likely to use in hob such which the entity semifinished materials hardly rolls being important again. After the hard alloy hob sharpens in front of the coating, suggested carries on the pretreatment to its cutting edge.The hob rewill sharpen can except the cutting surface original coating, this will be able to reduce the cutting tool life. The cutting tool is may again spread. Usually regarding the TiN coating, may spread 3 ~ 4; Says regarding TiCN and the TiALN coating, because coating itself has the very big internal stress, therefore on cutting edge with difficulty again again coating. After several spreading TiN coating, can have the height non-uniformity condition, and influentials the tendency which the level falls off, therefore the original coating must remove.At present has two methods to be possible to remove the cutting tool coating: Chemistry draws back spreads draws back with physics spreads. Draws back with chemistry spreads removes on the hard alloy tools the coating is one kind of fine craft, requests the operator to have the suitable level of expertise. The excessively chemistry draws back spreads not only removes the coating, moreover also will dissolve washes the cobalt cement, the damage hard alloy material microscopic structure. The cutting edge microscopic damage will produce the zigzag surface. In addition, when draws back spreads must to the hob pillow block, in the hole and the sign carries on the protection, in order to avoid damages. But physics spreads, then must carry on by the original cutting tool factory, it involves to puts in order rerubs the hob tooth profile truncates. Although draws back chemistry spreads must be much more expensive than, but obtains is a new hob, the quality and the life all can obtain the guarantee.To gear-hobbing machine requestIn order to fully displays the hard alloy and the coating craft merit, the gear-hobbing machine should do correspondingly improves. At present all advanced gear-hobbing machines all press high speed roll the tooth to carry on the design, its gear-hobbing machine hob rotational speed surpasses 3000r/Min, usually is5000r/Min, the work piece main axle rotational speed and the hob rotational speed match. In addition, the engine bed has very high moves the rigidity and the hot rigidity. The advanced gear-hobbing machine some main design characteristics are: Uses the compound epoxy resin lathe bed, by improves the engine bed the tendency and the static characteristic; Has the constant temperature installment the high speed hob headstock; High speed work piece main axle; May use does, the wet two kinds rolls truncates the craft; Belt electro-optical sensor digital actuation system; The straight line rolls the guide rail system; High speed automatic high-quality goods (2 ~ 3 seconds); The occupying a land area of is compact; According to man-machine engineering design; Services conveniently.Uses scrapes the craftRegardless of is the mechanical type the CNC gear-hobbing machine all can carry on scrapes, but the condition is the engine bed must equip has the work piece to the cutting tool selsyn train system. This may cause to scrape the craft economically, to has on the automatic yummy treats system the engine bed very to be also important. The electronic non- contact system depends on a simulation quantity sensor to send out the pulse to survey the cutting tool main axle, the work piece main axle and the gear position. The engine bed CNC controller carries on processing to these pulses, then is opposite to the work piece main axle in the cutting tool position carries on the adjustment, causes a work piece turn of tooth and the hob knife tooth relative position relations is correct.In scrapes in the craft to have very many merits with the refrigerant: In scrapes in the process, the refrigerant has provided the lubricating ability; Because scrapes produces is not the normal scrap, the temperature control is extremely important. Blows the scrap small is thin, does not look like normal knife filings such to be possible to carry off many quantity of heats, therefore scrapes time uses the refrigerant to be possible to control the cutting tool, the work piece and the engine bed system temperature; The refrigerant may washes away the scrap from the cutting tool and the work piece; Improved the work piece surface fine roughness; Enhanced the cutting tool life."Rolls in the green truncates" in the craft, correctly chooses the tooth thick remainder is very important. The recommendation choice down milling rolls the tooth, because it may obtain the thickest scrap, this is helpful to the control cutting process dynamic condition, enhances the cutting tool life. The experience proved that, the cutting speed may surpass 200m/Min, enters for the quantity choice is decided by the superficially attractive fineness which must achieve. The model enters for the scope is 0.5 ~ 1.25mm/R. The cutting tool shifts (flees knife) the method very to be also important, because scrapes time only then the rough machining section partial cutting edges only then undergo the attrition. On the contrary, in "the green cutting" in the process, the cutting tool precision work has partially undertaken the main process load. This meant when scraping flees the knife quantity to be supposed to be bigger, when like the gear is 12 ~ 48DP, each time flees the knife quantity is 0.3 ~ 0.4mm.Scrapes the hob the selectionScrapes the hard alloy hob to divide into two big kinds: Uses in 10DP or the bigger modulus hob, usually all designs has a negative rake front the cutting, when the cutting edge contacts to the hard tooth face, reduced to the hard alloy material impact; Regarding the small modulus gear, does not need to have the negative rake. The negative rake hob shortcoming is sharpens the difficulty. After the hob sharpens the outer diameter to reduce, in order to obtain the correct negative rake to be supposed to change the grinding wheel the bias quantity.When scrapes, the big modulus gear, its addendum, the outer annulus diameter and the tooth root spot all are usually not rolled truncates, and has a smooth transition a request turn of tooth to the tooth root. In order to obtain sinks cuts with the integrity transition circular arc radius, enhances the tooth root the anti- curved intensity, uses in the big modulus gear ideal scraping the hob to be supposed to have the flange. Regarding the small modulus gear processing, should use the standard hob. Uses the standard in front of the radial direction the angle hard alloy hob processing to be called "the hard alloy hob to roll again cuts", but is not "scrapes", latter referred has used a negative rake hob.Hardly rolls the specification which truncates and hardly scrapes the specification which, or the hard alloy hob rolls again truncates nearly same, similarity is uses the strategy which flees the knife to shift to be different. When hardly rolls, the scrap excision must spend the massive energies. This energy finally becomes the quantity of heat. Tries to carry off very important these thermal sending out. After the suggestion processes a work piece every time, the hob flees a position entire tooth pitch. When the hob will flee from beginning to end the position from now on, will be supposed to transfer to the hob to the initial position has a bias quantity the spot. This bias quantity is decided by the hob design and the application, its goal is for be helpful to the hob uniform wear. Another one similarity is the attire which uses clamps the system. As a result of the enormous cutting force, the jig must safely clamp the work piece. The processing result indicated that, the identical helical gear when hardly rolls again with the hard alloy hob, its gear quality is very high, the tooth profile approaches the AGMA10 level, the tooth to surpasses the AGMA12 level with the tooth pitch; The entire hard semifinished materials hardly roll cut the processing the helical gear, its gear precision extremely is also high, the tooth profile precision may reach the AGMA10 level, the tooth to may achieve the AGMA12 level with the tooth pitch. ConclusionAt present has explored many economies the method to process the hard gear, including the material choice, the soft processing method, the heat treatment craft and the hard precision work, enable the hard gear to obtain the popularization, has satisfied the high grade transmission device to the hard gear request.Carries on from entity entire hard work piece semifinished materials hardly rolls cuts the processing is one kind of new processing craft. Because has a rigid better engine bed and the high quality hard alloy tools material and performs coating processing, causes hardly to roll slivers is one effective processing method. Indicatedfrom the factory practical application result that, the hard gear rolls cuts (hardly rolls) the craft to have the broad application prospect.译文：淬硬齿轮的加工【摘要】用于动力传动的齿轮和齿轮箱，其尺寸要求更小，齿轮传动的噪音更低，从而导致对淬硬齿轮的需求，也给齿轮制造厂家提出了探索齿轮加工新方法的要求.概述用于动力传动的齿轮和齿轮箱，其尺寸要求更小，齿轮传动的噪音更低，从而导致对淬硬齿轮的需求，也给齿轮制造厂家提出了探索齿轮加工新方法的要求。