最后的叶片长度：660mm
13Annular area of the last blade: 4.14 m2
14Cooling surface area of the condenser: 4000 m2
凝汽器冷却面积：4000 m2
15Points for non-controlling extraction: Behind stages No 5, 8, 11, 15, 17, 19
Force: 1 kgf = 9.8067 N Pressure: 1 kgf / cm2= 0.098067 MPa Heat:1 kcal = 4.1868 KJ
Note: definitions of "left" and "right" sides: Being viewed in the direction from the steam turbine towards the generator, the left hand side is defined as the "left" side whereas the right hand side is defined as the "right" side. Definitions of "front" and "rear" ends: the end close to the steam turbine is defined as the "front" whereas the end close to the generator is defined as "rear" end.
类型：冲动式、高压、高温、单缸、单轴冷凝汽轮机
3Guarantee output (TMCR condition): 60MW
保证输出（TMCR工况）：60 MW
4Maximum power (VWO condition): 64.5MW
最大功率(VWO工况)：64.5MW
5Rated condition (TMCR condition) parameters:额定工况参数
21 Executive standard of the product::GB 5578-85Specification for Stationary Steam Turbines Driving Generator.
1-2 Technical and Economic Target and Promise Conditions
*
1-1
1 Main Technical Specification and Economic Target
1-1 Main Technical Specification
1Model: N60-8.83
型号：N60-8.83
2Type.- impulse type, high pressure, high temperature, single cylinder, single shaft condensing steam turbine
e)Inlet temperature of the cooling water: 30°C冷却水进口温度30°C
f)Makeup water temperature: 235.4°C补给水温度235.4°C
6Maximum steam flow: 245t/h主蒸汽流量245t/h
7Rotation direction: clockwise when viewed in the direction from turbine to generator
Equip. Supplier
DONGFANG TURBINE Co., Ltd
Document No.: (WBK)D60F-000100BSMRev :A
Document Title :
N60-8. 83 M^miMiM^
N60-8.83 Turbine Instruction Manual
(Main Turbine)
In this instruction the pressures for the thermal system are presented in absolute pressure. The instruction uses legal measuring units system which can be converted .into engineering measuring units by means of the following:
a)Main steam pressure: 8.83MPa主蒸汽压力8.83MPa
b)Main steam temperature: 535°C主蒸汽温度535°C
c)Main steam flow: 225.8t/h主蒸汽流量225.8t/h
d)Back pressure: 8.5kPa背压8.5kPa
* The shaft critical speed of generator refers to the data provided by the manufacturing company of the generator.
10Number of stages: 21 stages in total, consisting of 1 governing stage +20 pressure stages
Cylinder
2
13
3-3
Steam Fairway Arrangement
2
14
3-4
Valves and Pipes
2
15
3-5
Slide Key System and Differential Expansion
2
16
3-6
Turning Gear
2
17
3-7
Insulation and Enclosure
The control system of this unit is low pressure electric regulation.
控制系统是低压电液控制
This instruction manual mainly describes the general design of the unit and the structure of the turbine proper. Please refer to related technical documents provided with the machine for detailed descriptions on related auxiliaries, governing, protection and safety systems, installation and maintenance, start-up and operation, and various systems. If the instruction conflicts with technical documents provided, the documents shall prevail.
1
18
3-8
Temperature and Pressure Monitoring
1
19
4
Manufacturer Name and Address
1
Page 1 of 1
Compilation Description
N60-8.83 type steam turbine is a 60 MW turbine model that is designed and manufactured based on the advanced technologies that are introduced domestically and internationally. It is a new kind of condensing turbine of impulse type, high temperature, pressure and single cylinder. It matches boiler of corresponding capacity and steam turbine generator to form thermal generation unit. It is of basic load in electricity grid, and can also regulate the peak.
17Weight of the steam turbine: ~141t, (including valves, steam pipes, frame and levelling parallels)
18Maximum lifting weight: ~25 tons(for lifting upper cylinder assembly during maintenance)
~38 tons(for lifting lower cylinder assembly during installation)
19Maximum lifting height : 6.36m (with respect to the operation floor) 20.Elevation of the operation floor: 8 m
2
8
2-3
Steam Contribution and Operation Modes
1
9
2-4
Water-spraying System for Rear Cylinder
1
10
3
Constructional Features of Turbine Proper