LogosMarking of Vehicle PartsPrevious issuesVW 10514: 1966-01, 1973-01, 1974-03, 1998-09, 2001-01, 2002-06, 2002-11, 2006-03, 2007-06,2010-05ChangesThe following changes have been made compared with VW 10514: 2010-05:–Table 1, Škoda logo type M: Identification number in the engineering data management system(KVS) was LOG.000.008; KVS identification numbers for types R, N omitted, reference to VW 10522 omitted–Table 1, Audi logo type G: KVS identification number omitted–Section 3: Department abbreviation for the Product Definition Department changed –Section 5.2, Škoda logos: Types R and N omitted ContentsPageScope .........................................................................................................................2Requirements .............................................................................................................2Regulation ..................................................................................................................2Volkswagen AG and Audi logos .................................................................................3Other logos used in the Volkswagen Group ...............................................................4Seat S.A. logo as per VW 10517 ...............................................................................4ŠKODA AUTO a.s. logo .............................................................................................5Lamborghini logo ........................................................................................................5Bugatti logo ................................................................................................................5Bentley logo (6)The wordmark (Group logo) (6)123455.15.25.35.45.56Group StandardVW 10514Issue 2011-06Class. No.:01151Descriptors:vehicle part, logo, markingVerify that you have the latest issue of the Standard before relying on it.This electronically generated Standard is authentic and valid without signature.The English translation is believed to be accurate. In case of discrepancies, the German version is alone authoritative and controlling.Page 1 of 7Confidential. All rights reserved. No part of this document may be provided to third parties or reproduced without the prior consent of the Standards Department of a Volkswagen Group member.This Standard is available to contracting parties solely via the B2B supplier platform .© Volkswagen AktiengesellschaftVWNORM-2010-08f-patch1Other applicable documents ......................................................................................77ScopeVehicle parts, supply parts, and/or original parts of the Volkswagen Group must be marked with the corresponding logos in accordance with this Standard, provided that this is technically feasible.NOTE 1 The logos shown herein are solely of informative nature. The dimensions specified in the logo designations are examples. Dimensions and proportional data necessary for marking parts are available as data records in the KVS. The appropriate design engineering department will provide these data to the manufacturers.RequirementsParts must be marked in such a way that durability and legibility of the marking are ensured over the service life of the parts. The marking must be applied to the parts using suitable manufacturing meth‐ods such as, e.g., embossing, etching, or electric discharge machining.Downstream processing steps must not adversely affect the legibility of the marking.NOTE 2 Preferably, the marking is to be applied by incorporating it into the manufacturing tool. Labels,tags, and similar items must not be used for marking parts in accordance with this Standard.RegulationWhether or not a part must be marked is specified by the responsible design engineering department by using the standardized text macro (VW 01014, ID no. NO-E2) in the drawing.The logo type must always be specified in the drawing. If this specification is missing, type "S" must be used.The responsible engineering department may deviate from the necessity of marking parts only in consultation with K-VO-GL, the Product Definition Department, Quality Assurance, and the Standards Department.Parts which cannot be marked for design reasons such as, e.g., notch sensitivity (high notch stresses)or lack of space, are excluded from the marking requirement.Volkswagen and Audi are entitled to inspect the production facilities of vehicle parts bearing their respective logos and to take random samples from ongoing part production.If there is a lack of space, the logo marking takes precedence over the country of origin (VW 10550),the manufacturer´s code (VW 10540-1), the part number, the date marking (VW 10560), and the material designation (VDA 260).The fonts/symbols of the logos must be twice as large as all other markings on the part.Which logos are to be applied to vehicle parts of different brands must be determined as shown in Table 1 in accordance with their use in vehicles of the different brands.The type of application, i.e. cast, punched, etched, embossed, stamped, electric discharge machined,raised, or recessed, must be defined in the drawing. If this is not the case, the choice is left to the manufacturer.123Page 2VW 10514: 2011-06Table 1 – Overview of in-house Standards/data records for marking of vehicle partsa)Type G not to be used for new designsVolkswagen AG and Audi logosVehicle parts that are used exclusively in vehicles of the Volkswagen brand must be marked with the logo types C, Figure 1, and O, Figure 2.NOTE 3 Type C is to be used preferentially.NOTE 4 The letters V and W as well as the circle surrounding them (d1-2a) must be designed such as to appear raised from the perspective of a person looking at the marked component.Vehicle parts which are used exclusively in vehicles of the Audi brand must be marked with the logo type D, Figure 3.See VW 10500 as well as the Standards listed in Table 1 for further design rules.Figure 1 – Type CLogo for Volkswagen AG (Table 2)Figure 2 – Type OLogo for Volkswagen AG (Table 2)4Page 3VW 10514: 2011-06Figure 3 – Type DLogo for Audi AG (VW 10513)Figure 4 – Type G(Not to be used for new designs)Designation of a type C logo with a nominal diameter of d 1 = ∅ 10 mm:Logo VW 10514 – C 10Designation of a type D logo with a nominal length of L 1 = 20 mm:Logo VW 10514 – D 20Table 2 – Dimensions for types C and O (mm)Nomi‐nal di‐ame‐ter d 11,622,5345681012162025324050d 31,92,342,933,54,75,8579,311,61418,623,329,137,246,558,2a 0,140,170,210,260,340,430,510,680,851,021,361,72,132,723,44,25b 0,160,20,250,30,40,50,60,811,21,622,53,245c0,040,050,060,080,10,130,150,20,250,30,40,50,6250,811,25Definition of dimensions: d 3= 1,163 d 1; a = 0,085 d 1; b = 0,1 d 1; c = 0,025 d 1Other logos used in the Volkswagen Group Seat S.A. logo as per VW 10517Figure 5 – Type F Figure 6 – Type JDesignation of a type F logo with a nominal height of h = 10 mm:Logo VW 10514 – F 10Designation of a type J logo with a nominal length of l = 20 mm:Logo VW 10514 – J 205 5.1Page 4VW 10514: 2011-06ŠKODA AUTO a.s. logoFigure 7 – Type MKVS identification number LOG.000.015Designation of a type M logo with a nominal diameter of d = ∅ 16 mm:Logo VW 10514 – M 16Lamborghini logoFigure 8 – Type TKVS identification number LOG.000.010 dated 2002-02Designation example for a type T logo with a nominal height of h = 20 mm:Logo VW 10514 – T 20Bugatti logoFigure 9 – Type UKVS identification number LOG.000.011 dated 2002-03Designation example for a type U logo with a nominal length of l = 20 mm:Logo VW 10514 – U 205.2 5.35.4Page 5VW 10514: 2011-06Figure 10 – Type WKVS identification number LOG.000.014 dated 2002-11Designation example for a type W logo with a nominal length of l = 20 mm:Logo VW 10514 – W 20Bentley logoFigure 11 – Type VKVS identification number LOG.000.012 dated 2002-02Designation example for a type V logo with a nominal height of h = 10 mm:Logo VW 10514 – V 10The wordmark (Group logo)If identical vehicle parts are used in vehicles of several brands, the type S marking, Figure 12, mustbe used. Both the size and the position of the Group logo must be as inconspicuous as possible.Figure 12 – Type SIf technically possible, the font Thesis TheSans is to be used for the lettering.KVS identification number LOG.000.006Designation example for a type S logo with a nominal height of h = 5 mm:Logo VW 10514 – S 55.56Page 6VW 10514: 2011-06Other applicable documentsThe following documents cited in this Standard are necessary to its application.Some of the cited documents are translations from the German original. The translations of German terms in such documents may differ from those used in this Standard, resulting in terminological inconsistency.Standards whose titles are given in German may be available only in German. Editions in other languages may be available from the institution issuing the standard.VW 01014Engineering Drawings; Drawing Frames and Text Macros VW 10500Company Designation, Marking of Parts; Guidelines for Use VW 10513Audi Logo for Vehicle PartsVW 10517SEAT Symbol; Brand Logo for Vehicle Parts VW 10540-1Manufacturer's Code for Vehicle Parts VW 10550Country-of-Origin Marking; Vehicle Parts VW 10560Date Marking; Vehicle PartsVDA 260Components of motor vehicles; marking of material7 Page 7VW 10514: 2011-06。