七.塑料與咬花深度
1. 脫模度預留 0.5 度或 0.005 mm 深/安全量 2. tolerance is +/- 0.0025mm (Hommel Tester T1000 精密測試 測試
(0.005mm) 0.0002
(0.005mm) 0.0002
3. PS
ABS
PC
[ 黏度 (viscosity) / 流動長度 ]
NO:12
Hommer Tester T1000 C - 320 Dat:-------------Nr:---------------Lt = 15 mm Lc = 2.5 mm Ra = 04.53 Um Rz = 26.92 Um Rm = 32.16 Um Nr = 00057/cm
梨 地
NO:9
六. 咬 花 粗 度 比 較 / 精 密測 試
以下是使用德國 出 表面粗度, 深度及圖形, 藉此可 明白區分噴砂, 梨地,皮紋及寫真等類花 紋之不同. 主要符號說明如下: Ra: 算 術平 均 粗 度 值 Rz: 山 谷 平 均 值 Rm: 最 大 山 谷 深 度 值 噴 砂
4. exp: apple G-1 texture
minimum draft required:3.5度 for ABS & PC, 2.5度 for PVC
PLASTIC SPECIFICATION STEEL SPECIFICATION ===================================== DEPTH NR DEPTH NR (in/1000) pk/in (in/1000) pk/in (Microns) pk/cm (Microns) pk/cm
Hommer Tester T1000 C - 320 Dat:-------------Nr:---------------Lt = 15 mm Lc = 2.5 mm Ra = 09.81 Um Rz = 56.24 Um Rm = 64.32 Um Nr = 00032/cm
柄 NO:26
Hommer Tester T1000 C - 320 Dat:-------------Nr:---------------Lt = 15 mm Lc = 2.5 mm Ra = 23.79 Um Rz = 91/.16Um Rm = 92.64 Um Nr = 00012/cm
咬花製作參考資料
TEXTURE # MT-11400 MT-11405 MT-11410 MT-11415 MT-11420 MT-11425 MT-11430 MT-11435 MT-11440 MT-11445 MT-11450 MT-11455 MT-11460 MT-11465 MT-11470 MT-11475 MT-11480 DRAFT 3 4 5.5 3 4 5.5 10 15 1.5 2.5 4 4.5 5.5 7.5 3 3 4.5 ° DEEP. .002 .0025 .0035 .002 .0025 .0035 .007 .010 .0005 .0015 .0025 .003 .0035 .005 .002 .002 .003
MOLD-TECH
TEXTURE # MT-11300 MT-11305 MT-11310 MT-11315 MT-11320 MT-11325 MT-11330 MT-11335 MT-11340 MT-11345 MT-11350 MT-11355 MT-11360 MT-11365 MT-11370 MT-11375 MT-11380 DRAFT 3.5 ° 7.5 ° 7.5 ° 1.5 4 4.5 3 3 4.5 4.5 5.5 4 5.5 7 6 6 6 DEEP. .0025 .005 .005 .001 .0025 .003 .002 .002 .003 .003 .0035 .0025 .0035 .0045 .004 .004 .004
Hommer Tester T1000 C - 320 Dat:-------------Nr:---------------Lt = 15 mm Lc = 2.5 mm Ra = 12.18 Um Rz = 58.84 Um Rm = 64.88 Um Nr = 00023/cm
皮
紋
寫
真
NO:NH4044
咬花製作參考資料
TEXTURE # MT-11200 MT-11205 MT-11210 MT-11215 MT-11220 MT-11225 MT-11230 MT-11235 MT-11240 MT-11245 MT-11250 MT-11255 MT-11260 MT-11265 MT-11270 MT-11275 MT-11280 DRAFT 4.5 4 5.5 6.5 7.5 6.5 4 6 2.5 3 4 3 6 7 6 5 8 DEEP. .003 .0025 .0035 .0045 .005 .0045 .0025 .004 .0015 .002 .0025 .002 .004 .005 .004 .0035 .0055
GOAL 1.8 - 2.1 45 - 53 ACCEPTABLE 1.7 -2.2 43 - 56
>60 >24
2.2 - 2.5 55 - 64
>80 >31
>50 >20
2.1 -2.6 53 - 66
>70 >28
15 mm
15 mm
15 mm
15 mm
MOLD-TECH
TEXTURE # MT-11000 MT-11010 MT-11020 MT-11030 MT-11040 MT-11050 MT-11060 MT-11070 MT-11080 MT-11090 MT-11100 MT-11110 MT-11120 MT-11130 MT-11040 MT-11150 MT-11160 DRAFT 1°? MIN 1.5 2.5 3 4.5 6.5 4.5 4.5 3 5.5 9 4 3 4 4 4 6 DEEP. .0004 .001 .0015 .002 .003 .0045 .003 .003 .002 .0035 .006 .0025 .002 .0025 .0025 .00275 .004