第二章访问MP可以通过MP serial port 或者MP LAN port 登陆MP，默认的用户名/口令为：Admin/Admin 登陆过程：*************************************************************************This is a private system.Do not attempt to login unless you are an authorized user.Any authorized or unauthorized access or use may be monitored and canresult in criminal or civil prosecution under applicable law.**************************************************************************************************************************************************Only default users are configured.Use one of the following user/password pairs to login:Admin/AdminOper/Oper*************************************************************************MP login: AdminMP password: *****Hewlett-Packard Integrated Lights-Out HP Integrity and HP 9000(c) Copyright Hewlett-Packard Company 1999-2004. All Rights Reserved.MP Host Name: mp-rx2620Revision E.03.15************************************************************************* MP ACCESS IS NOT SECUREDefault MP users are currently configured and remote access is enabled.Modify default users passwords or delete default users (see UC command)ORDisable all types of remote access (see SA command)************************************************************************* ************************************************************************* Your Certificate is expired.Use the SO command to generate a new certificate.************************************************************************* MP MAIN MENU:CO: ConsoleVFP: Virtual Front PanelCM: Command MenuCL: Console LogSL: Show Event LogsCSP: Connect to Service ProcessorSE: Enter OS SessionHE: Main Help MenuX: Exit Connection2.1 serial port使用任意终端仿真软件通过主机专用的串口线连接，具体设置为2.2 MP LAN port通过网线连接，直接telnet MP LAN port 的IP 地址第三章常用命令注意：MP里的一些命令将对正在运行的系统造成破坏性影响，请不要随意操作，必须在响应中心工程师指导下进行。

Command DescriptionBO Boot a partitionDA TE Set the time and dateDF Display FRU Information of an entityMA Return to Main MenuPE Power entities on or offPWRGRD Allows user to configure the power gridRE Reset entityRR Reset partition for reconfigurationRS Reset a partitionSYSREV Returns all system revisionsTC Send a TOC signal to a partitionTE Broadcast a message to all users of the MP command handler WHO Display list of MP connected usersLOC Display and Set Locator LED statusCP Display partition cell assignmentsDE Display entity statusDU Display devices on busHE Display the list of available commandsLS Display LAN connected console statusPS Display detailed power and hardware configuration status CA Only displays local rs232 parametersCC Initiate a Complex ConfigurationUPS Set parameters for ups monitoring via SNMPSNMP Set SNMP daemon parametersCP Display partition cell assignmentsDC Reset parameters to default configurationDI Disconnect Remote or LAN consoleID Change certain stable complex configuration profile fields IF Display network interface informationIT Modify command interface inactivity time-outLC Configure LAN connectionsLS Display LAN connected console statusPARPERM Enable/Disable Interpartition SecurityPD Modify default Partition for this login sessionRL Re-key complex profile lockRU Reset MP bus deviceSA Display and set MP remote accessSO Configure security options and access controlXD MP Diagnostic and reboot3.1 检查系统log一般情况下，我们只需要关注错误级别为Warning 以上的LOG MP MAIN MENU:CO: ConsoleVFP: Virtual Front PanelCM: Command MenuCL: Console LogSL: Show Event LogsCSP: Connect to Service ProcessorSE: Enter OS SessionHE: Main Help MenuX: Exit Connection[mp-rx2620] MP> slEvent Log Viewer Menu:Log Name Entries % Full Latest Timestamped Entry---------------------------------------------------------------------------E - System Event 805 80 % 13 Aug 2008 00:47:27F - Forward Progress 4000 100 %B - Current Boot 78 26 %P - Previous Boot 2 0 % 09 Aug 2008 12:39:39C - Clear All LogsL - Live EventsEnter menu item or [Ctrl-B] to Quit: eLog Name Entries % Full Latest Timestamped Entry--------------------------------------------------------------------------- E - System Event 805 80 % 13 Aug 2008 00:47:27Event Log Navigation Help:+ View next block (forward in time, e.g. from 3 to 4)- View previous block (backward in time, e.g. from 3 to 2)<CR> Continue to the next or previous blockD Dump the entire logF First entryL Last entryJ Jump to entry numberH View mode configuration - HexK View mode configuration - KeywordT View mode configuration - TextA Alert Level Filter optionsU Alert Level Unfiltered? Display this Help menuQ Quit and return to the Event Log Viewer MenuCtrl-B Exit command, and return to the MP Main MenuMP:SL (+,-,<CR>,D, F, L, J, H, K, T, A, U, ? for Help, Q or Ctrl-B to Quit) >t MP:SL (+,-,<CR>,D, F, L, J, H, K, T, A, U, ? for Help, Q or Ctrl-B to Quit) >a Alert Level Threshold Filter:1 : Major Forward Progress2 : Informational3 : Warning5 : Critical7 : FatalEnter alert level threshold or [Q] to quit filter setup: 3-> Alert threshold level 3 filter will be applied.MP:SL (+,-,<CR>,D, F, L, J, H, K, T, A, U, ? for Help, Q or Ctrl-B to Quit) > 3.2 Dump 全部的logdump 就是将系统保存的日志全部显示出来出来。