E M C V P L E X安装实施方案-标准化文件发布号：（9456-EUATWK-MWUB-WUNN-INNUL-DDQTY-KIIVPLEX-LOCAL的硬件配置信息此次安装的VPLEX-Local有单台台VPLEX组成，VPLEX的硬件配置如下：1)1个Engine2)2个Director，每个Engine由两个Director组成3)8个8Gb前端FC端口，每个Director包含一块前端FC卡，共4个8Gb的前端FC端口，由于交换机端口限制，本次使用4个前端FC端口（每个Directo上两个）。

4)8个8Gb后端FC端口，每个Director包含一块后端FC卡，共4个8Gb的后端FC端口。

本次使用4个前端FC端口（每个Directo上两个）5)4个可用的8Gb的VPLEX-Local级联FC端口，每个Director包含一块VPLEX-Local级联FC卡，共4个8Gb的级联FC端口，但是只有两个可用VPLEX-LOCAL的硬件介绍单台VPLEX的硬件布局VPLEX的ENGINE的硬件布局拓扑结构VPLEX-LOCAL的FABRIC拓扑图Fabric Switch Engine power supplyManagement serverFabric SwitchVNX VNXVPLEX Host HostVPLEX-LOCAL 后端存储系统的配置META VOLUME 的配置请注意每台VNX 必须使用两个RG ，每个RG 各提供两个80G LUN 。

Mirror 和backup 的meta volume LUN 需分开RG 存放。

不推荐mirror 和 backup 放在同一个RG 里。

LOGGING VOLUME的配置安装配置流程VPLEX-LOCAL安装配置详细步骤在VPLEX-Local的安装配置过程中，有些命令在Manager Server上运行，有些命令在VPLEX上运行，以下标志代表命令的运行场所：【MS_CLUSTER_1】: VPLEX_01的Manager Server的shell环境下运行【VPLEXCLI_CLUSTER_1】: VPLEX_01的VPlex的CLI环境下运行，在Manager Server的shell环境下，运行“vplexcli”命令进入该环境【MS_CLUSTER_2】: VPLEX_02的Manager Server的shell环境下运行【VPLEXCLI_CLUSTER_2】: VPLEX_02的VPlex的CLI环境下运行，在Manager Server的shell环境下，运行“vplexcli”命令进入该环境CLUSTER_1的安装配置CLUSTER_1的初始化配置1.将配置用的笔记本电脑的网卡设置为通过DHCP获取IP2.配置用的笔记本电脑通过网线连接到VPLEX_01的Manager Server的eth1网口3.通过或SecureCRT软件登陆到VPLEX_01的Manager Server上，Host IP：，Connect type：SSH，用户名：service，密码：Mi@Dim7T4.设置Manager Server的主机名【MS_CLUSTER_1】# sudo /opt/emc/VPlex/tools/ipconfig/ -n VPLEX-015.重新登陆Manager Server，查看提示符或/etc/HOSTNAME文件内容，确认主机名更改成功【MS_CLUSTER_1】# cat /etc/HOSTNAME6.运行vplexcli命令登陆到VPLEX_01，用户名为service，密码为Mi@Dim7T【MS_CLUSTER_1】# vplexcli7.配置Manager Server的管理公用IP地址【VPLEXCLI_CLUSTER_1】# management-server set-ip -i VPLEX_01_IP:VPLEX_NETMASK -g VPLEX_GATEWAY eth3【VPLEXCLI_CLUSTER_1】# ll /management-server/ports/eth38.运行exit命令，退出VPLEX_01到Manager Server，检查公用管理网络的连通性【VPLEXCLI_CLUSTER_1】# exit【MS_CLUSTER_1】# ping VPLEX_GATEWAY9.配置NTP时钟服务器，同步时间【MS_CLUSTER_1】# vi /etc/ ; 设置外部server为NTP_IP【MS_CLUSTER_1】# sudo /etc/ntp restart【MS_CLUSTER_1】# date10.运行exit命令，退出VPLEX_01的Manager Server【MS_CLUSTER_1】# exit11.通过或SecureCRT软件登陆到VPLEX_01的Manager Server上，用户名为service，密码为Mi@Dim7T12.运行vplexcli命令登陆到VPLEX_01，用户名为service，密码为Mi@Dim7T【MS_CLUSTER_1】# vplexcli13.启动VPLEX的Director，确认显示的director数量正确（2个director）【VPLEXCLI_CLUSTER_1】# configuration connect-local-directors【VPLEXCLI_CLUSTER_1】# ll /engines/**/directors14.检查VPLEX及每个Director的版本，确认符合版本控制要求【VPLEXCLI_CLUSTER_1】# version【VPLEXCLI_CLUSTER_1】# exit15.检查VPLEX及每个Director的版本，确认符合版本控制要求【MS_CLUSTER_1】VPlexPlatformHealthCheck确认检查结果符合下表：运行EZ-SETUP配置向导16.运行EZ-Setup配置向导，完成以下方面的配置：【MS_CLUSTER_1】# vplexcli【VPLEXCLI_CLUSTER_1】# configuration system-setup提示选择2What would you like to configure1. Configure a VPLEX Local (single cluster).2. Configure a VPLEX Metro (synchronous, 2 clusters).3. Configure a VPLEX Geo (asynchronous, 2 clusters).Select your configuration choice. (1-3)What would you like to configure11. Configure the first or only cluster.2. Configure the second cluster of a VPLEX Metro implementation.Select your configuration choice. (1,2)Are you sure you want to configure the first or only cluster (yes/no): yesWould you like to configure the login banner (yes/no): noWould you like to configure an authentication service provider to authenticate VPLEX users (yes/no) [no]: noWould you like to configure this cluster to send event notifications to EMC (yes/no) [yes]: noWould you like to configure this cluster to send system reports to EMC (yes/no) [yes]: noWould you like to configure the cluster to run the SNMP Agent Service (yes/no) [no]: noHow many years should the CA certificate remain valid before expiring EMC recommends 5 years (maximum5is 5 years). [5]:2How many years should the host certificate remain valid before expiring EMC recommends 2 years(maximum is 2 years). [2]:Would you like to run the setup process now (yes/no): yesguizhou_sfdx Please create a passphrase (at least 8 characters) for the Certificate Authority Key. Make a note of thispassphrase as you will need it to configure a second cluster of a VPLEX Metro or Geo. Certificate Authoritypassphrase:Re-enter the passphrase for the Certificate Authority Key: guizhou_sfdxguizhou_sfdx Please create a passphrase (at least 8 characters) for the Local Host Certificate Key. Make a note of thispassphrase as you will need it later. Host Certificate passphrase:Re-enter the passphrase for the Certificate Key: guizhou_sfdx 配置CLUSTER_1与后端存储系统之间的ZONE17.获取VPLEX_01端口的WWN【VPLEXCLI_CLUSTER_1】# ll /engines/**/ports18.登陆到SAN Switch，运行“switchshow”命令，检查VPLEX_01后端端口在SAN Switch上的连接是否符合规划，否则根据规划进行调整19.登陆到SAN Switch，创建与Metadata Volume和Logging Volume相关的VPLEX_01后端端口与后端存储系统前端端口之间的zoneVPLEX注册到后端存储系统及磁盘分配VPLEX_01的后端端口注册到VNXVPLEX_01的后端端口在VNX上的注册配置建议如下：Host name: VPLEX_01Host IP: VPLEX_01_IPInitiator type: CLARiiON OpenFailover Mode: 4VNX上创建STORAGE GROUPStorage Group: SG_ VPLEX_01Host: VPLEX_01_1LUN: 2个78GB的Metadata Volume（800、801）和一个10GB的Logging Volume（802），以及其他数据LUN识别后端存储系统的METADATA VOLUME和LOGGING VOLUME20.识别后端存储系统和相应的磁盘设备【VPLEXCLI_CLUSTER_1】# configuration continue-system-setup创建METADATA VOLUME21.获取适合创建Metadata Volume的磁盘设备，比较VPLEX的VPD名字与VNX LUN的VPD名字，确认VNX5400的LUN 800的VPD名字和VNX5400的LUN 800的VPD名字【VPLEXCLI_CLUSTER_1】# configuration show-meta-volume-candidates22.创建Metadata Volume【VPLEXCLI_CLUSTER_1】# meta-volume create -n VPLEX_01_META -d < VXN5700的LUN 800的VPD名字>,< VNX5400的LUN 800的VPD名字>23.查看Metadata Volume的状态，确认active属性列显示为true【VPLEXCLI_CLUSTER_1】# ll /clusters/cluster-1/system-volumes/ VPLEX_01_META24.查看cluster的状态，确认cluster status和operational-status显示为ok【VPLEXCLI_CLUSTER_1】# cluster status25.获取适合创建Metadata Volume Backup的磁盘设备，比较VPLEX的VPD名字与VNX LUN的VPD名字，确认VNX5400的LUN 801的VPD名字和VNX5400的LUN 801的VPD名字【VPLEXCLI_CLUSTER_1】# ll /clusters/cluster-1/storage-elements/storage-volumes26.选择Metadata Volume的备份设备为：VNX5400的LUN 801的VPD名字>,< VNX5400的LUN 801的VPD名字>。