置于…
Locate on …
检验
Inspection
(Or: Check)
6.可制作性报告(DFM Report):
中文(Chinese)
英文(English)
中文(Chinese)
英文(English)
变形
Deform
(n. Deformation)
确认
Confirm
(n. Confirmation)
英文(English)
折弯内圆角
Internal Bend Radius
点焊
Spot welding
印字
Mark part NO.
(Stamp part NO.)
缝焊
Seam welding
按照制造说明安装…
Install… Per Manufacture’s instruction
氩焊
Argon welding
接地标志
Ground symbol
自攻牙
Self-tap
(Form thread or Swirl)
半剪
Half-shear
攻牙
Tap (thread)
压线
Score
工艺槽,狭缝
Relief
(Slot)
印字
Mark
(Stamp)
异形小折
Finger
抽桥
Draw bridge
标签定位压印
Label locator mark
折弯
Bending
毛刺面
Burr side
后定规
Back gauge
去毛刺
Deburr
折床
Press brake
模具,工具
Tooling
折弯线
Bending line
攻牙机
Tapping machine
铆钉机
Hardware insertion Machine
点焊机
Spot weld machine
Or. (Be) cracked
平行度
Parallelism
错位
Mismatch
倾斜的
Slant
偏离
Deviate
(n. Deviation)
太窄
Too narrow
太弱
Too weak
缩减
Reduce
刮伤
Scratch
对齐
Align
(n. Alignment)
制造
Fabricate
(n. Fabrication)
避位孔
Clearance
向上抽引,抽凸
Up draw forming
(Or: Up emboss)
段差
Offset
向下抽引,抽凸
Down draw, forming
(Or: Down emboss)
卡槽
Card guide
凸点
Bump
(Dimple)
抽芽孔
Threaded extrusion hole (or: Extrude and tap)
(Need washer)
组装
Assembly
轴肘式铆接
Toggle lock
冲头
Punch
冲裁方向
Punch direction
用螺丝实配来
检查色拉孔
C’sink to be measured using a mating screw as a gauge
螺丝头须与
装配面平齐
Head of screw must sit flush with mating surface
中文(Chinese)
英文(English)
中文(Chinese)
英文(English)
圆棒
Round Bar
弹簧螺钉
Captive screw
(Spring-loaded screw)
螺母
Nut
销钉
Pin
平头螺母
Nut flush
铍铜静电导片
Gasket, becu, EMI
自锁螺母
Nut self-clenching
工件不对称
Unsymmetrical part
折弯系数
Folding factor
折弯线共线
Same bending line
正(反)面印字
Mark from Nearside (Farside)
外径
Outside Diameter
(Abbr. OD)
代号
Mark
内径
Inside Diameter
(Abbr. ID)
Chromate
丝印
Silkscreen
(Or. Pad print)
镀镍
Nickel plating
拉丝
Line grinding
(Or: Brush)
钝化
Passivate
非电解镀
(化学镀)
Electroless plating
不烤漆区
Free of paint area
外观
Cosmetic
烤漆保护
青铜
Bronze
材料清单
Bill of material
(Abbr. BOM)
样品
Prototype
功能
Function
量产
Production
修改
Modify
像素
Feature
忽略…
Forget (to do) Sth.
(Ignore Sth)
缩短, (使)变短
Shorten
延长, (使)变长
Lengthen
缩短2mm
Shorten by 2mm
7.其他类(Miscellaneous):
不锈钢
Stainless Steel
(abbr. SUS or SS)
见放大图A
See detail A
冷轧钢板
Cool roll steel
(abbr. CRS)
外(内)表面
Exterior (Interior) surface
热浸镀锌钢板
Hot-dip zinc coated steel (or Galvanized Iron. Abbr. GI)
Button-head screw
垫片
Washer
拉钉
Rivet
弹簧
Spring
平头拉钉
Flat head rivet
标准件
Standard parts
圆头拉钉
Dome head rivet
(Or: closed-end rivet)
定位销
Dowel pin
散热器
Heat sink
3.表面处理类(Finish category):
孔离折线太近
The hole is too close to the bending line
生锈
Rust
(Or. Corrosion)
尺寸公差
Dimensional tolerance
间隙
Gap
平面度
Flatness
间隙过大
Excessive gap
垂直度
Straightness
断裂
(Be) broken,
剖视图A-A
Section A-A
高度
Height
局部视图A
Detail A
C向视图
View from C
比例4:1
SCAL 4:1
宽度
Width
数量
Quantity (Qty.)
Or. Amount
长度
Length
备注
Remark
打磨平齐
Grind Flush
规格大小
Specification
(Abbr. Spec.)
装…拉钉用
For rivet …
请用旧模具…
Please use old tooling…
装…螺丝用
For screw…
每片料下4个单件
4pcs/sheet
(4pcs per sheet)
抽铆用
For staking
毛刺面向上
Burr up
工件对称
Symmetrical part
未注明的
Unmarked
需开工艺槽
Need cutting relief
建义
Suggestion
折弯内尺寸太小
Inside bending dimension is too short
解决办法
Solution
抽形太高
Forming is too high
目前刀具规格
Current tooling spec.
Or available tooling
重点尺寸
Critical Dimension
抽铆
Staking
随制造日期变化
Date changes according to actual Manufacture date
拉铆
Riveting
压铆五金件
Press (install) hardware
机加工
Machining
下料
Blank (Blanking)
Painting masking
镀亮锡
Bright Tin Plating
镀锌
Zinc plating
喷沙
Sand blasting
4.图面注解类(Notes on drawing):
中文(Chinese)
英文(English)