第一章炼钢连铸词汇1.1 AActive power 有功功率Agitate 搅拌Air cooled stopper 气冷塞杆Aluminum feeder 加铝器Ammonia still 蒸氨塔Amplitude 振幅Anode 阳极AOD(Argon-Oxygen Decarburization) 氩氧脱碳工艺Aperture 小孔Arbor 辊轴Armature 电枢Armour-plate 装甲板，防弹钢板Articulated spindle 铰接主轴Artificial neutral transformer 接地变压器1.2 BBack-pressure valve 止回阀Base metal 母材Basic converter steel 碱性转炉钢Basic lining 碱性炉衬Basic slag 碱性渣Batch cast 间歇浇铸Bath level 溶池液面Bearing area 支撑面积，承载面积Bearing steel 轴承钢Belt casting 带式连铸Bending radius 弯曲半径Bending stress 弯曲应力Bessemer converter 酸性转炉Bifurcated launder 分叉流槽Billet unscrambler 小方坯自动堆垛台Blast tuyere 风口Blast wheel 抛头Bleeding 铸坯缝漏钢Blister free steel 无气孔钢Blister 气孔Block mould 整体结晶器Bloom 大方坯BOF（basic oxygen furnace）氧气顶吹转炉Bogie/ buggy casting 台车浇铸Bogie/ buggy ladle 车载钢包 Boilings 溢出的钢渣Bonded metals 包层金属板BOS（basic oxygen steel plant）碱性氧气炼钢设备 Bottom blown oxygen converter 底吹氧气转炉Breaking load 断裂负载Breakout 漏钢Broad-flanged beam 宽缘工字钢Buffer 缓冲器，减震器Build-up mould 组合结晶器Bushing 轴衬，衬套Butt ingot 短锭，半截锭Butt joint 对接，平接1.3 CCalcinate 煅烧Cam throw 凸轮偏心度，凸轮行程Canopy and enclosure damper 屋顶罩和密闭罩挡板Capacitance 电容Carbide 硬质合金Carbon injection lance 碳枪Carbon penetration 渗碳Carburizer 渗碳剂Carry on device 上料机构Cascade 串连的布置Casting bay 浇铸跨Casting buggy 铸锭车Casting floor 浇铸场Casting speed 浇铸速度，拉速Casting stand 浇铸台Cathode 阴极，负极Caustic embrittlement 碱性脆化Cementation 渗碳Center line shrinkage 中心收缩孔Checked edge 裂边Chestnut 出铁口的栗铁Chipping 表面清理Circlip 簧环Clad steel 复合钢Clay mortar / fire-clay mortar 耐火灰浆，粘土火泥 Command variable 控制变量Conservator 保油箱Conveyor pallet mould system 台车式结晶连铸装置Cooling grid 冷床Corrosion inhibitor 减蚀剂Crank 曲轴Creep speed 蠕变速度Critical cooling rate 临界冷却速率Cross girder 主横梁Cross travelling trolley 横移小车Crucible steel 坩埚钢Curvature 曲率Curvemeter 曲率计Cushion 减震垫Cut lengths 定尺长度Cut-out switch 切断开关Cut-over 切换Cutter arbor 铣刀杆Cutter blade 刀片Cutter head 铣刀头Cutting nose 刀尖Cutting out 断路Cutting ring 环刀Cutting-off 停车Cybernetic control 计算机控制Cybernetic Model 控制论模型Cybernetics 控制论Cycle annealing 循环退火Cycle fatigue 周期疲劳Cycle counter / cymometer 频率计Cycle slipping 跳周Cycle slipping rate 周期平滑率Cycloidal pump 摆旋泵Cyclone collector 旋风集尘器Cyclone combustion chamber 旋风燃烧室Cyclone filter 旋风过滤器Cyclone scrubber 旋风洗涤器Cylinder 液压缸，汽缸Cylinder manifold 汇流排Cylinder valve 气缸阀Cylindrical roller thrust bearing 圆筒形滚柱止推轴承 Cylindrical surface 圆柱面Cyma 反曲线Cyrtolite 曲晶石1.4 DDaily mean 按日平均Daisy chain 菊花链Damper 调节挡板Damper gear 阻尼装置Damping capacity 吸湿能力Damping decrement 衰减率Damping circuit 衰减电路Deep groove ball bearing 深槽滚珠轴承Dependent variable 因变量Deseam 表面精整Direct strand reduction 直线串列式轧制 Directional solidification 定向凝固Distributing launder 布料槽Double slag 返回渣Down spout 出渣槽Doy-bar type conveyor 凸轮式输送机Drain sleeve 冷凝管Drum chart recorder 滚筒式图表纪录器Dry binder 干式粘合剂Ductility 可延展性1.5 EEffervescent steel 沸腾钢Electric potential 电位Extra lattens 热轧特薄板1.6 FFerritic steel 铁素体钢Ferroconcrete 钢筋混凝土Filling brick 塞头砖Fissure 龟裂Flux 熔剂Flux powder 造渣粉末Skull 结渣1.7 GGangway 过桥Gantry crane 龙门起重机Gaseous inclusion 内压气泡Goggle 护目镜1.8 HHard metal alloy 硬质合金Heat dissipation 热扩散，热耗散Heat transfer coefficient 热传导率Heat convection 热对流High vacuum melting furnace 高真空熔炼炉 Hollow cone 空心圆锥Homogeneous 均质的，均匀的Hopper funnel 漏斗Hot deseamer 热火焰清理机Hot scorching 热轧件的火焰清理Hysteresis 磁滞，滞后1.9 IIgnition loss 灼烧损失Implode 内爆Inclined conveyor type machine 斜送式连铸机Inert gas 惰性气体Ingate 内浇口Ingot butt 锭底，锭尾Ingot stripper 脱锭机Ingot tilter 翻锭机Ingot tongs 夹锭钳Insolvable anode plate 不溶性阳极板Introduction of dummy bar 引锭杆引入Inverse segregation 逆偏析1.10 KKey bar 键杆Key way 键槽Killed steel 镇静钢Kinetic energy 动能1.11 LLadle buggy 钢包台车Ladle chair 钢包支撑座Ladle lid 钢包盖Ladle lip 钢包嘴Ladle nozzle 钢包水口Ladle pouring time 钢包浇铸时间Ladle preheating plant 钢包预热装置Ladle shank 钢包转手Ladle skull 钢包残钢Ladle stopper 钢包塞杆Ladle tilter 钢包倾倒装置Ladle turret 钢包回转台Launder 出铁槽LD-AC Process 氧气顶吹和碳粉氧气顶吹法LD process 氧气顶吹转炉炼钢法Line frequency 工频Line frequency induction furnace 工频感应电炉Line voltage 线电压Loading bucket 加料斗Loss of temperature 温度损失Low carbon free cutting steel 低碳快速加工钢Low head continuous casting machine 低压头连铸机 1.12 MMain substation 总降变电站Make-up water 补给水Malleability 可塑性Mangle roll 矫正棍Manipulator 控制器Manometer pressure gauge 压力表Marshalling cabinet 编组柜Megger / megohmmeter 兆欧计，摇表Melting loss 熔炼损失Mitre gear 等径伞齿轮Mould cavity 结晶器型腔Mould cooling jacket 结晶器冷却套Mould reciprocation 结晶器往复运动Mould saddle 结晶器托台Mould wall 结晶器壁Multi stage mould 多联结晶器1.13 NNegative segregation 负偏析Non-metallic inclusion 非金属夹杂物Non-swirl nozzle 无旋流喷嘴Nozzle fouling 喷嘴堵塞1.14 OOccluded gases 内在气体Occlusion 封闭，阻塞Off-take 出口，排出口Oil bath 油浴Oil nipple 加油嘴OLP-converter ( oxygen lance powder ) 氧气石灰粉喷吹转炉 On-to-tap duration 通电开始到出钢时间Open mould 开式结晶器Oxide skin 氧化皮Oxygen converter steel 氧气转炉钢Oxygen core lance 单孔氧枪Oxygen enriched air blast 富氧鼓风1.15 PPacking ring 垫圈Peak load 峰值负载Pendant control panel 悬垂式控制器Peripheral speed 圆周速度Phase inversion 倒相Phase lag 相位滞后Phase lead 相位超前Phase shifter 移相器Phase to phase 相位间的Pick-up carbon 增碳Pitted surface 有凹痕的表面Pony ladle 小包Powder cutting 铁末氧切割Primary cooling zone 结晶器冷却区Pusher 推钢机Pyrometric cone equivalent 当量测温锥 1.16 QQuiet steel 全镇静钢1.17 RRadial stress 径向应力Rammed lining 捣实式炉衬Ramp generator 斜坡发生器Ratchet 棘轮Reaction roller 反力辊Reactive power 无功功率Reactive power compensation 无功补偿 Reactor 电抗器Reflectoscope 超声波探伤仪Rejected steel funnel 废钢料斗Resonance 共振Restrictor 杆式限制定位器Retainer ring 扣环Return roll 平回辊Reverberatory furnace 反射炉Rimming steel 沸腾钢Rocker 摇杆Rocking spout 移动式铁水溜槽Roller apron 导辊装置Runner gate 流钢闸门Running-in period 开始运转期Rupture stress 断裂应力1.18 SScattered value 离散值Scintillation counter 闪烁计数器Scoop sample 熔池取样Screen plate 成品筛板Screw die 板牙Seger cone 塞氏温度熔锥Shaft 轴，炉身Sheath tube 保护管Shunt 分路器，分流器Sieve 过筛，过滤Siphon ladle 虹吸式盛钢桶Skid bank 滑轨，冷床Skimmer 撇渣器，挡渣板Skull 炉瘤Skull correction 包底补正Slag dam 挡渣Slag inclusion 熔渣夹质Slag runner / launder spout 流渣沟Slag-free tapping 无渣出钢Soft free-cutting steel 易切削低碳钢Spirit level 气泡水准仪Spur track 接头钢轨Spur wheel 正齿轮Stopper brick 堵塞砖Stopper rod 堵塞杆Suction casting 真空铸造Surge 涌流Surge arrester 避雷器Surge current 冲击电流Susceptance 电纳SVC (static var compensation) 静态无功伏安补偿Swinging launder 流动出钢槽Swiveling tundish 旋转中间包1.19 TTap flap open 出钢口盖板打开Tap Hole 出钢口Tap-to-tap water 自来水Tapping spout 出钢槽Tapping view 出钢画面Thermal diffusivity 热扩散率Threshold value 临界值Throttle valve 节流阀Torsion strength 抗扭强度Tundish carriage 中间包小车Tundish turret 中间包回转台Turn over cooling bed 倾变冷却床1.20 VVacuum degassing 真空脱气Vertical type continuous casting machine 立式连铸机 Vessel 转炉炉身Vibrator motor 振动电机Vacuum oxygen degassing 真空脱氧1.21 WWater cooled roof 水冷炉盖Water cooled walls 水冷炉壁Water jacket 水套Withstand test 耐压试验Wormgear 涡轮减速机第二章宽厚板轧机词汇2.1 （机械部分）2.1.1 AAbort escape system 紧急逃逸系统Abort handle 应急把手Abrasion resistant 抗磨的,耐磨的Absorption of moisture 吸湿，吸潮Abrupt change 急剧[突然]变化Acceleration ramp 速度爬升，加速斜坡Accumulator 活套Acid resistant 耐酸的Acoustic baffle(damping; enclosure; panel; barrier) 声障板Actuator 执行机构Air inlet duct 空气入口管道Air knife 气刀Air pocket 气穴Air damper 节气门Air cushion 气垫Air cooler 空气冷却器Allen key 艾伦内六角扳手Amplification factors 放大系数Anti-flutter roll 防振辊Anti crimping roll 抗皱轴AOD process 氩氧脱碳法Application software 应用软件Approach roller table 输入辊道Arithmetic mean value 算术平均值Armour plate 护板Articulated dummy bar 铰链引锭杆As-built construction drawing 建设竣工图纸Asynchronous motor 异步电动机Axial runout 轴向跳动Accelerated plate cooling equipment 快速冷却装置（ACC）Adjustment system (wedges) for the top and bottom rolls including W edgecylinder 上下矫直机调整系统（斜锲）包括斜锲油缸Adjustment system for the entry and exit rolls 入口、出口矫直辊调整系统Agitator 搅拌器Air cylinder 气缸Air pressure tank 空气压力罐Antifriction bearing 防摩擦轴承Anti-rusting coat 防锈涂层Apron 挡板，裙板Automatic valves 自动阀Manual valves 手动阀Motorized valve 电动阀Roller bearing 滚柱轴承2.1.2 BBackpressure 背压Backlash compensation 间隙补偿Backstop 托架，止回器Backup rolls 支撑辊Backup roll assembly 支撑辊装配总成,Backup roll bending 支撑辊弯曲Backup roll change (dismantle) stool 支撑辊更换（分解）托架Backup roll cleaning device (extractor) 支撑辊清理装置（提取设备）Backwash water 反冲水,回洗水Baffle plate 隔板, 挡板Bag filter 袋式滤器Bag house 袋滤捕尘室Baling band 打包窄钢带Baling press 打包机Baling wire 打包钢丝铁丝Ball valve 球阀Bank of pumps 水泵机组排Bar coded label 条形码标签Bar mill 小型轧机Barrel hardness 辊身硬度Base line [测]基线Battery limit 界限，界区Battery power supply unit 电池供电机组Bayonet locking 卡口锁定Bearing chocks 轴承座Bearing clearance 轴承余隙Bearing extractor 轴承提取装置Bearing end play 轴承的轴向间隙Bearing thrust 轴承推力，轴承止推Belt wrapper 助卷皮带Belt wrapper tucking arm 助卷皮带压臂Bending stress 抗弯强度Bifurcated launder 分叉流槽Bleed port 泄放孔Block diagram 框图Block circuit 闭塞电路Bogie 小车Bolted connection 螺栓连接Booster pump 增压泵Booster fan 增压风机Bottom bending roller 下转向弯辊Bottom sump 废水坑Bottom-pour ladle 底流式钢包Bottom-tap ladle 底部放流钢包Bottom-roll motor 下轧辊马达Boundary friction 边缘摩擦Boundary lubrication 边缘润滑Clyburn spanner 活扳手Cock spanner 旋塞扳手Double spanner 双头螺丝扳Double-ended open-jawed spanner 双端开口爪形扳手 Double offset ring spanner 梅花扳手English spanner 活动扳手Hammering spanner 单头开口爪扳手Hose spanner 软管扳手Inner hexagon spanner 内六角扳手Ratchet spanner 棘轮扳手Brace nut 拉紧螺帽Breakout 漏钢，烧穿Breakout warning system 漏钢报警系统Breakout predication system 漏钢预报系统Brinell hardness test 布氏球印实验Bulk density 容积密度，单位容积重量Buried cable 直埋[埋地]电缆Butterfly valve 蝶形阀Bypass valve 旁通阀Back-up chocks 轴承座Back-up roll balancing 支撑辊平衡装置Back-up roll change rails 支撑辊换辊轨道Balancing cylinder & bracket 平衡缸及支架Bearing housing assembly 轴承组件Bed plates 地脚板Bending cylinders 弯辊缸Bending frame 弯辊框架Bottom knife table 下剪刃台Brackets for hydraulic cylinder 液压缸支架Breast rollers 机架辊Bridging table for roughing stand 粗轧机过桥辊道 Bucket car 废料斗小车Bumper 减震装置BUR balancing cylinder 支撑辊平衡油缸Bushing (spindle head holder) 轴瓦（扁头套保持架）Bushing and sliding liners 轴瓦和滑动衬板2.1.3 CCantilevered beam 悬臂Carryover moment 传递力矩Chain-type dummy bar 链式引锭杆Chock separator 轴承座分离器Chock tilter 轴承座翻转装置Chute roller table 滑行辊道Cobble bar kick-off device 废品钢筋清理装置Cooling header 冷却集管Cooling tower 冷却塔Crop shear 切头, 切尾剪Crop shear entry guide 切头剪进口导板Crow bar / Pry bar 撬杠Curb plate 侧板,转护板Curved apron plate 弧形挡板Cam 凸轮Carrier beam 框架梁Carry out table 过渡辊Center guides 对中导板Central gear lube oil filling system 集中齿轮润滑油加油系统Central filling system for MORGOIL-oil 摩戈伊尔铝硅锡合金轴承集中加油系统Central fresh oil filling and waste oil collecting system 集中加油和废油收集系统Chasing tool （车）螺纹工具Chainways 链轮轨道Clamping rolls 夹紧辊Cold plate leveller entry table 冷矫入口辊道Conditioning bed 精整台架Cooling bed entry table 冷床入口辊道Cooling bed walking beam type 冷床步进梁 (CB)Counterweight 配重，对重Cover for hydrostatic slide way 静压导轨盖Crank shafts 曲柄轴Crank shaft bushing 曲柄轴轴瓦Cross transfer device 横移装置Cross transfer run out table 横移装置输出辊道Cross type spindle 十字接轴Crowned tooth coupling 鼓形齿接手Cylinder piston 油缸活塞Cylinders for top work roll bending 上工作辊弯辊油缸 2.1.4 DDelay roller table 延时除鳞辊道Descaling box 除鳞箱Descaling spray header 除鳞箱喷淋水管喷淋头Descaling spray unit 除鳞箱喷水总成Double door air lock 双门气塞Door latch bolt 门碰簧销Downlooper 下活套Disappearing stop 升降挡板Disc roller 盘辊Distribution conveyor 分配运输装置Dividing shear depressing table 剖分剪摆动辊道Double side trimming shear proper 双边剪本体Drag chain 拖链，牵引链Drive base frame 传动底座框架Drive spindle 主传动轴Drying oven 烘干炉Dust collector 除尘收集装置2.1.5 EEdge buildup 边部形成Edge heating 边部加热Edge cracking 边裂Edger balance system 立辊平衡系统Edging passing 立辊轧过Edge masking 边部挡板Edger housing 立棍牌坊Edger roll bearings 立棍轴承Edger roll 立辊Emergency collapse 紧急收缩Emergency cutout 紧急切断Entry guide 进口导板Entry roller 入口辊子Entry trailer 进口拖车Embedded conduits 预埋电气管Embedded parts 预埋件End stop 末端挡板Exhaust duct 排气管道2.1.6 FFactory-calibrated 工厂校准的Factory- wired 工厂配线的Fault tracing 故障查寻Fault locating 故障定位Fault induction 故障感应Feedback system 反馈系统Finishing mill 精轧机Finishing pass 精轧道次Flattening press 压平机Flux powder 熔剂粉Fume exhaust 排烟Fume exhaust ductwork 排烟管道系统Furnace campaign 炉龄期Finishing stand 精轧机架Fire alarm system 火警报警系统Fire hazard area 火险区Fish tail 划伤Finned tube 片管Feed rollers 机架辊Film thickness gauge 涂膜厚度仪Flame cutting machine 火焰切割机Flatness gauge 平直度仪Flexible coupling 弹性［挠性］接手 Flowmeter 流量计Four-high finishing stand 四辊精轧机Frequency converter: 调频转换器2.1.7 GGas analyzer 气体分析仪Gas hazard indicator 有害气体显示器Gas sealing 气体密封Garter spring 卡紧弹簧Gauge pressure 表压Gauge run-up 厚度增加Guide rail 导轨Get out of round 脱圆Glareless light 不刺目的灯Go on stream 投入生产Going askew 跑偏Gothic pass 弧边菱形轧槽Gravity separation 重力分离Grease gun 注油枪Grouting compound 灌浆料Grouting concrete 灌浆料Grub screw 埋头螺钉Guard railing 栏杆，扶手Gusset plate 角撑板，加固板Guy rope 定绳Guyed 用牵索加固的Guide roller carrier 导辊托架Gear couplings 齿轮接手Gear rack and pinion 齿轮齿条Gear rack and sliding liners assembly 齿条和滑动衬板组件Gear rack drive 齿条传动装置Grease distribution valve for table 辊道干油分配阀Grease distributor 干油分配阀2.1.8 HHard chrome plated 硬镀铬的Head end spotting 头端确定准确位置Headstock 主轴箱Heat dissipation 热消散Heat loss 热损失Heat number 炉号（熔炼）Heat reclamation 热回收Heat recovery equipment 热回收设备Heat retaining panel 保温板Heat retention hood 保温板罩Heat transfer coefficient 传热系数Helical gear 斜齿轮Hidden defect 隐蔽瑕疵High purity water 高纯水Holding time 占用[吸着, 保留]时间Holding table 冷却辊道Holding furnace 保温炉High pressure water descaling 高压水除鳞Hold down roller 压紧辊Hot plate leveler (HPL) 热矫机Hydrostatic oil lube system for double side trimming shear and slit ting shear双边和剖分剪静压润滑系统Hydrostatic oil lubrication 静压润滑Hydrostatic plates 静压板2.1.9 IInsulating pit 保温坑 Insulating plate 绝缘板Insulating tube 绝缘管 Integral vertical edger 集合立辊Inter stand cooling 机架冷却 Idler shaft 惰轮轴Idling roll 惰辊 Idling speed 空转速度Immersion nozzle 浸渍喷嘴管 Immersion probe 浸渍探头Immersion thermocouple 浸液式热电偶 Impact load 冲击负载Impact test 冲击试验 Impact strength 冲击强度Impairment of quality 质量损害 Impervious to dust (sound) 无（声）Impingement angle 碰撞角 Impregnation tape 渍注量尺Inboard end sealing 内侧密封Inclination error of axes 轴的倾角误差Individual error 个别误差Indoor lighting 室内照明Inert gas 惰性气体Ingress of water 水的进入Inherent error 固有[内在]误差Inserted length 插入长度Inside micrometer caliper 内测千分卡尺Inspection procedure 检验程序Inspection declined 谢绝参观Instrument air 仪表气源Intake pressure 进气压Integrated circuit 集成电路Interface 交界面，离合面Interlock 联锁装置Intermediate roller table 中间辊道Isometric drawn picture 等角图Inserts for oil-air-lubrication 油气润滑用衬垫Interconnecting p iping 中间配管Intermediate cooling device 中间冷却装置2.1.10 JJacket tube 管套 Jack up 顶起Jaw chuck 齿卡盘 Job lot production 小批生产Jogging control 点动控制Jogging duty 点动负载 Journal 端轴颈，轴颈Journal rest 轴颈支承 Thrust journal 止推轴颈Junction box [电] 接线盒,分线箱Jib crane 悬臂吊车2.1.11 KKeyboard entry 键盘输入key seat gauge 键槽规Keyway键槽keyway slotting 键槽孔Kick plate 踢板Kinematic viscosity 动粘度Knife holder 刀架Knife shim 剪垫片Knuckle radius 封头过渡区半径Knife change car 剪刃更换小车Knife saddles 剪刃盒2.1.12 LLadle car 钢包车Ladle slide gate 钢包滑动水口Ladle skull 桶瘤Ladle furnace 钢包炉Ladle turret 大包旋转台Ladle turret with lift arm 带升降臂的大包旋转台Laminar flow 层流Laminar flow jet stream 层流喷水流Lap joint 接搭处Lateral thrust 侧向推力Launder 流槽Lifting arm 升降臂Light barrier 挡光板Limit switch 限位开关Load cell 压头Load profile 负载分布 Local tripping 局部跳闸Load diagram 荷载图Lock nut 锁紧螺母Locking pin 锁定销 Locking segment 锁闭片Longitudinal travel 纵向移动 Looper 活套Looper roll 活套辊Lower pinch roll 下夹送辊Lubrication chart 润滑系统图Lube oil 润滑油Luminous dial 发光度盘Length measuring rollers 测长辊Lifting crossbeam 升降框架Lifting cylinder 升降液压缸Light aligning equipment 激光对中装置LP–琱ydraulic system –Auxiliaries mill area LP—液压系统—辅助系统LP–hydraulic system –Servo-controls mill area LP—液压系统—伺服系统—轧机区Lubrication distributor 润滑分配器2.1.13 MMagnaflux testing method 磁通量考核法Main mandrel shaft 卷筒主轴Magnet clutch 电磁离合器 Main gear housing 主齿轮箱Maintenance platform 维修平台Malfunction indication 故障指示Malfunction time 故障时间Mandatory standard 法定标准Mandrel 卷筒Mandrel segment 卷筒扇形体Marking machine 喷印机Marking template 喷印模板Mass flow 物流Mass moment of inertia 质量惯性矩Master controller 主控制器Mating part 配合部件Measuring roller 测量辊Measuring head 测量头Measuring instrument 测量仪器Measuring kit 测量工具Micro alloyed structure steel 微合金结构钢Mill edge 轧制的(未经剪切的)边，热轧缘边Mill spindle carrier 轧机连接辊托架Mill spindle positioner 轧机连接辊定位器,定位装置Mirror image 镜像Mist eliminator 汽水分离器Mnemonic abbreviation 助记缩语Mobile crane 移动式起重机Moisture separator 脱湿器Molybdenum disulphide 二硫化钼Moment of torsion 扭（转力）矩Momentary overload 瞬时过载Motor actuator 电机执行机构Motor splashing guard 电机防溅板Mould oscillator system 结晶器振动系统Mould tackle 结晶器吊装工具Mounting tolerance 安装公差Multi-hole nozzle 多孔喷嘴Multi-step control 多步骤控制Mushroom head bolt 扁头螺栓Mechanical screw down system 机械压下系统Mill housing 牌坊Mill stand piping 机架配管Mix tank with agitator 搅拌罐Motor coupling 马达接手Moveable end stop 移动末端挡板Moveable grid 移动隔栅Moveable track 移动轨道2.1.14 NNatural gas 天然气NDT (Non Destructive Testing) 无损检验Nickel-chromium steel 镍铬钢Nipple plate 凸纹钢扳Nitrogen pressure reducer 氮气减压器No-load run (operation) 空载运行No-load test 无负荷测试Noise absorbing 吸音Noise insulating cover 隔音罩Non-contact measurement system 无接触测量系统 Non-cutting pass 无切割轧制Non-dazzling lighting 无耀眼照明Non-driven roller 非驱动辊Non-shrinking grout 不收缩灌浆Non-swirl nozzle 无漩涡喷嘴Non-thrust bearing 无止推轴承Normal backlash 正常间隙，齿间隙Normal wear and tear 正常磨损Nozzle erosion 喷嘴腐蚀Nozzle fastening 喷嘴固定Nozzle fouling 喷嘴污垢Needle roller bearing 滚针轴承2.1.15 OO-ring gland (seal) O形环密封Oblique position 倾斜位置Oblong hole 长圆孔，椭园孔Off-button 关闭按钮Off-load 卸载的Offset switch 偏移开关Oil atomizer 喷油器Oil baffle plate 挡油板Oil cellar 地下油库Oil collecting trough 油收集槽Oil cooler 油冷却器Oil drain hole 放油孔Oil flinger 抛油环Oil fume 油烟气Oil mist lubrication 油雾润滑Oil return flow 回油流量On-Off controller 开关控制器Ooze out 泄露Open pass 开放轧制Open water-cooling circuit 敞开水冷回路Open loop control 开环控制Operating characteristics 运行特性Operational chart 作业流程图Operation scheduling 作业计划Operator’s cab 值机室Operator’s platform 操作员平台Orifice plate 流量孔板OS (operating side) 操作侧Oscillating system 振动系统Oscillation mark 振痕Out of stock 已脱销Out of roundness 不圆度，椭圆度Outboard support bearing 外支撑轴承Outdoor Substation 室内配电变电所Outdoor switchgear 室外开关设备Outdoor storage area 室外存储区Outmost warp 最外面翘曲Outline drawing 外形图Output amplitude 输出信号振幅Output speed 输出速度Overhead traveling crane 桥式起重机Over speed trip 过速跳闸Overtime pay 加班费Overtime rates 加班费Oxide film 氧化膜Oxide layer 氧化层Oxygen torch slab scarfing machine 火焰表面清理 2.1.16 PPacking list 装箱单Paging system 传呼系统Pan for waste paint 废漆盘Pan head 全景云台，摇摄云台Partial view 局部视图Partition wall 隔断墙Parallel connection 并联Pass line 轧制线Passing contact 滑动接触Patching mortar 修补沙浆Pay-off reel 开卷机Peak stress 峰值应力Peak strain 峰值张力Peak torque 最大转矩Peel bar 推钢机的推杆Peeler knife 开皮刀Peeler knife holder 开皮刀夹具Percussion drill hammer 冲击钻机Perforated plate 多孔板, 冲孔板Performance test 性能考核试验Period for tendering 招标期Permeability to water 透水性Perpendicularity 垂直，直立Personal injury 人身事故Persuader roll 摇杆辊Photoelectric cell 光电管Pickling line 酸洗机组Pickup recess 收取凹坑Piling cradle 堆垛筐架 Pillow block 枕垫，枕座Pinch roll carrier arm 夹送辊托架臂 Pinch roll gap 夹送辊缝Pinch roll unit 夹送辊总成Pipe coupling 导管接头Pipe reducer 渐缩管Pipe stub end 管的大头端Pipe swivel joint 管的回转接头Pipe trench 管沟Piston rod 活塞杆Pivot 枢轴Pivot bearing 立式止推轴承Pivot journal 枢轴颈，轴节Pixel 像素Plain carbon steel 普通碳钢，碳素钢 Plain washer 平垫圈Plant fire brigade 工厂消防队 Plant safety rules 工厂安全条例Plasma arc cutting 等离子弧切割Plastic dowel 塑料榫钉Plastic wall anchor 塑料墙壁锚栓件 Plate mill 厚板轧机Plate piler 厚板堆垛机Plate turnover device 翻板装置 Platform weighing machine 台式称量机 Plumb bob 铅锤Pneumatic cylinder 气缸Pneumatic hammer 气锤Plywood 夹板Polar moment of inertia 极惯性矩 Porter bar 夹持工具Pressure accumulator 蓄压器Pressure gauge 压力计Pressure boosting station 增压站Pressurize 增压，密封，使...加压Prick punch 划线冲子，打标记冲子Probe cable 探头（探测器）电缆Probe well 探头井Process data 工艺数据Processor 处理器Procurement drawing 购置图Product liability 产品责任Product mix 产品大纲Product tracking 产品跟踪Production schedule 生产计划Propagation of crack 裂纹的扩展Proportional valve 比例阀Proximity switch 接近开关Pipe support and pipe clamp 管支架和管卡Plane shape gauge 板形测量仪表Planetary gear drive 行星齿轮箱Plate marking machine 喷印机Pneumatic brake to worm gear unit 涡轮减速箱用气动抱闸 Pneumatic system 气动系统Pusher arm 推杆2.1.17 QQuality appraisal 质量鉴定Quality control 质量控制Quality grade 质量等级Quality standard 质量标准Quench and temper 淬火与回火Quick disconnection coupling 快脱开接头2.1.18 RRadiant tube 辐射管Radius of curvature 曲率半径Radius of gyration 回转半径Ragging of roll barrel 轧辊辊身压花，滚花Rain gutter 雨水沟Rake-type cooling bed 倾斜式冷床Rapid return motion 快速返回Rapid traverses 快速横移Ratchet wheel 棘轮Rated flow 额定流量Rated load 额定负载Rating plate 定额牌Reactor 电抗器Readout 读数,读出Ready mixed concrete 预拌混凝土Rear flank 背面Rear view 后视图Reciprocating movement 往复运动Recoiler 卷取机Refractometer 折射计Regulex 电机调节器Reject slab 不合格板坯Reignition voltage 再引弧电压Release for shipment 启运许可证Reliability in operation 可靠操作值Relief valve 安全阀Repair stand 修理台Repeated usage 重复利用Replace at regular intervals 定期更换Replace in case of need 需要时更换Replenish 补充，补给Reproducibility 复现性Resistant to water 防水Resonance speed 共振转速Retaining block 垫块Retract distance 收缩距离Retractable downcoiler 伸缩地下卷取机Return travel 返回行程Reusability 可重复使用性Reversing roughner 可逆式粗轧机座Revision sheet 修正报告Revolution counter 转速计Ripple marks 波纹Rocker arm 摇臂Rockwell hardness test 洛氏硬度测试Roll barrel 辊身Roll bending 轧辊挠度Roll changing 换辊Roll chock 轧辊轴承座Roll clamp 辊夹具Rock crown 轧辊顶部凸面Roll end sleeve 轧辊终端套管Roll eccentricity 轧辊偏心Roll extracting device 辊抽拔设备Roll gap 辊缝Roll grinder 轧辊磨床Roll keeper 轧辊夹头Roll neck seals 辊颈密封Roll pass design 轧辊孔型设计Roller pass apron 轧制道次挡板Root diameter 内螺纹外径或外螺纹内径Roughing mill 粗轧机Rotary shear 圆盘剪Roughing strain 粗轧应变Roughing stand 粗轧机架Rubber lagging 包衬橡胶Rubber lining 橡皮衬里Rubber coated roll 橡胶辊Rule of thumb 经验法则Runback 回流管Running up to speed 提速到Runout roller table (ROT) 输出辊道Rust inhibiting agent 防锈剂Reciprocating unit with motor 带电机往复装置Roll gap adjustment cylinders assembly 辊缝调整液压缸 Roller table 辊道2.1.19 SSaddle 鞍形座Saddle type coil conveyer 鞍形带卷运输机Safety cage 安全升降机Safety goggle 防护眼镜Safety guard 安全防护设施Sample pieces conveyor 样品传送机Sampling cock 取样旋塞Sampling punch 取样冲Saponification factor 皂化系数Saturated steam 饱和蒸汽Scale buildup 氧化皮堆积Scale jacket 氧化皮壳Scale pit 氧化皮坑Scale water pump 水锈泵Scale breaker 破鳞机Scheduled maintenance 定修Schematic wiring diagram 接线原理图Scleroscope hardness 回跳硬度Scleroscope 硬度计Seal element 密封元件Seaming roll 卷边滚轮Sectional view 截面图Seep out 漏出，渗出Segment changer system 扇形段更换系统Segment retainer link 扇形段护圈隔栅Self-aligning ball bearing 自动定心滚珠轴承Self contained power pack 自带电源Self-locking 自动上锁的Self-retarding gear 自动减速机构Self-ventilated 自行通风的Semi gantry crane 单脚高架起重机Sequence cast 连包连铸Sequence chart 程序图表Sequence of operations 操作顺序Service life expectancy 使用寿命Service water supply 用水供应Servo valve 伺服阀Servomotor 伺服马达Set roll gap 设定辊缝Setpoint ramp up 设定值上升Setpoint ramp down 设定值下降Settling tank 沉淀池Shaft alignment error 轴的对中误差 Shaft deflection 轴的偏差Shaft displacement 轴的位移Shaft outboard bearing 轴的外置轴承 Shaft gland 轴封Shallow tank pickle line 浅槽酸洗线 Shear force 剪力Shock absorber 减震器Shroud 长水口Shrouded pushbuttons 有罩按钮Side trimming shear 修边剪Sight glass 窥镜，观察孔Side looper 侧活套挑Single acting cylinder 单作用缸Sinusoidal oscillation 正弦振荡Siphon pipe 虹吸管Skimmer 撇渣器Skin-pass mill 精整机Skid bank 冷床Slab conditioning area 板坯清理区Slab turnover device 板坯翻转装置Slab yard 板坯库Slag inclusion 夹渣Slag runner 炉渣沟Slewing crane 旋臂[回转式]起重机Slewing pillar crane 转柱式起重机Slide gate 滑动水口Slide gate mechanism 滑动水口机构Slide contact 滑动接点Slight seepage 轻度渗漏Slipper block 滑块Slipping clutch 安全摩擦离合器Slitting shear 纵切剪Sloping ramp 装料斜台Sloppy concrete 喷溅混凝土Sludge dewatering 污泥脱水Slurry pump 淤浆泵Slush compound 蚀润滑剂Snap hook 弹簧扣Snubber roll 缓冲辊Soaking time 均热时间Soaking-in 电容器充电Soaking furnace 热炉Solenoid 电磁阀Spare part inventory 备件存货 Spherical spindle end 球形主轴端 Spigoted joint 插管接头Splash guard 防溅板Spray overlap 交错喷水Spray header 喷嘴集管Spraying nozzle 喷嘴Spreader bar 布料器Spring barrel 弹簧锁定装置 Spun concrete 离心成型混凝土Spurious oscillation 寄生振荡 Spur gear 正齿轮Squeegee roll 挤干辊Squirrel cage motor 鼠笼式电动机 Stackable pallet 可堆放托板 Staggered arrangement 交错布置Stacking crane 码垛起重机 Standby generating set 备用发电设备 Standby power supply 应急供电Starwheel 星形轮Static control 静态控制Steam trap 疏水器Steel beam trammel 钢梁长臂规尺Step ladder 人字梯Stock requisition 领料单Stopper 塞棒，制动器Storage rack 带卷垛存台架Straight edged coil 直边卷Straightening segment 矫直段Strand 铸流Stressmeter 应力计Strip pass line 带钢轧制线Stud bolt 双头螺栓Submerged nozzle 浸入式水口Successful bidder 中标人Sulphur acid 硫酸Surface crack 表面裂纹Synthetic resin bond 合成树脂粘固Shuttering work 模板工程Sensor 传感器Shifting head (Operator side) 串动头（操作侧）Short stroke cylinder 短行程油缸Shot blasting machine 抛丸机Slitting shear (SS) 剖分剪（SS）Sprocket wheels (for chain, return wheel) 链轮（链条，反转链轮用） Stainless steel tubes and fittings 不锈钢管和接头Structure for reciprocating unit 往复装置框架Sump pumps 污水泵Supporting rollers 支撑辊道Entry side guides 入口侧导板Swiveling joints 旋转接头Synchronizing shaft 同步轴2.1.20 TTail end kick off device 切头剪推尾装置Take over point (TOP) 交接点Take-up speed 卷带速度Taper gauge 锥度规Taper plug gauge 锥体塞规Tapered trunnion 渐缩的耳轴Target value 目标值Telescoped coil 塔形钢卷Telescopic cover 伸缩罩Telescopic floor plate 伸缩地板Temper rolling 平整Temperature detector 检温器Temperature gradient 温度梯度Tensile strength 抗张强度Tension bridle 张紧装置Tensioning roller 张力辊Terms of acceptance 验收条件Terms of delivery 交货条件Test certificate 检验合格证书Testing procedure 检验程序Thermal conductivity 导热性Thermal flux 热通量。